Cree IG Series Installation guide

Brand: Cree

Model: IG Series

Category: Decorative lighting

Type: Installation guide

IG Series

LED Parking Luminaire

Junction Box and Pendant Mount

INSTALLATION INSTRUCTIONS

1 of 2 LPN00305X0001A0_A

TO INSTALL:

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed

including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l’alimentation avant l’installation.

2. This luminaire must be installed in accordance with the NEC or your local

electrical code. If you are not familiar with these codes and requirements, consult

a qualied electrician.

Ce produit doit être installé conformément à NEC ou votre code électrique local.

Si vous n’êtes pas familier avec ces codes et ces exigences, veuillez contacter un

électricien qualié.

3. DO NOT lift luminaire by the power leads.

4. DO NOT carry or lift luminaire by wireform. Wireform is only for supporting luminaire while

making wiring connections.

SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE

JUNCTION BOX MOUNTING

STEP 1:

Attach mounting plate to customer

supplied junction box with the clips on the

Mounting Plate directed parallel to vehicle

traffic as shown in Figure 2. Torque to

20 in-lbs. See Figure 1 and 2.

STEP 2:

For hands-free wiring locate the wireform

on luminaire and attach it to the clip on

the Mounting Plate. See Figure 3.

STEP 3:

Make wiring connections per “Electrical

Connections” section.

STEP 4:

After wiring connections have been made,

tuck all wires into junction box ensuring

that no wires are pinched. Remove

wireform on luminaire from the clip on the

mounting plate. Fold the wireform back

down onto the luminaire.

STEP 5:

Attach luminaire to the Mounting Plate

by pressing up on the luminaire until the

slots on the luminaire engage with the

clips on the Mounting Plate and rotate

until clips lock securely. To secure install

a minimum of (2) supplied screws across

from each other into the mounting plate

clips on the underside of the luminaire.

See Figure 4.

NOTE: May require extra pressure on

luminaire to engage clips into slots. Only

apply pressure on housing body NOT on

the luminaire lens.

NOTE: If the mounting plate clips

become deformed during installation,

slightly reopen the clips back up using a

screwdriver to ensure proper install of

luminaire.

(4) Luminaire Slots

(4) Clips

Mounting

Plate

Mounting Plate

Wireform

Mounting

Plate Clip

View of Underneath

Luminaire

(4) Mounting

Plate Clips

Luminaire

Slots

(2) Screws

Mounting Plate

Wireform

Clips

Mounting Plate

NOTE:

• During installation and maintenance handle

the luminaire only by the housing NOT by the

lens.

2 of 2 LPN00305X0001A0_A

www.cree.com/lighting

See www.cree.com/lighting/products/warranty for warranty and specifications. Cree® is a registered trademark, and the Cree

logo is a trademark of Cree, Inc.

STEP 6:

Lightly pull on the luminaire to verify

luminaire is securely mounted.

FIXTURE SERVICING AND

MAINTENANCE

STEP 1:

If supply wiring splices need to be inspected

or if luminaire needs to be removed, fully

loosen the (2) screws and rotate luminaire to

disengage from Mounting Plate.

STEP 2:

To re-install luminaire, when finished with

servicing or maintenance follow Step 2-6 in

“Junction Box Mounting” section above.

PENDANT MOUNTING (OPTIONAL)

STEP 1:

Attach Pendant Mount Plate to customer

supplied pendant kit.

NOTE: Not recommended for use with a

hang straight pendant. Cree does not provide

a counterbalance system.

STEP 2:

Feed customer supplied leads through

customer supplied pendant kit and the

Pendant Mount Plate. See Figure 5.

STEP 3:

For hands-free wiring locate the wireform

on luminaire and attach it to the clip on the

Pendant Mounting Plate. See Figure 5.

STEP 4:

Make wiring connections per “Electrical

Connections” section. Once wire

connections have been made remove

wireform on luminaire from the clip on the

mounting plate. Fold the wireform back

down onto the luminaire.

STEP 3:

Attach luminaire to the Pendant Mounting

Plate by pressing up on the luminaire until

the slots on the luminaire engage with the

clips on the Pendant Mounting Plate and

rotate until clips lock securely. To secure

install a minimum of (2) supplied screws

across from each other into the pendant

mounting plate clips on the underside of the

luminaire. See Figure 5.

NOTE: May require extra pressure on

luminaire to engage clips into slots. Only

apply pressure on housing body NOT on the

luminaire lens.

NOTE: If the pendant mounting plate clips

become deformed during installation,

slightly reopen the clips back up using a

screwdriver to ensure proper install of

luminaire.

LED LUMINAIRE MAINTENANCE

CLEANING INSTRUCTIONS:

Regular cleaning of the light LED luminaire

is required to keep the LED luminaire

operating optimal optical performance.

• Cleaning intervals to be no more than

twelve months for IESNA Clean category

environments and more frequently for

dirtier conditions.

• Care should be taken as to not damage

the lens and/or the interior reflective

surface as these components are critical

for optimal performance.

• Do not use any type of cleaners or stiff

brushes on the LED luminaire. Use

water with mild detergent and soft cloth.

ELECTRICAL CONNECTIONS

STEP 1:

Make the following Electrical Connections for products rated 120V, 277V,

or 347V (Line-Neutral), or rated 208V, or 240V (Line-Line):

a. For products rated 120V, 277V or 347V, connect the Black lead

from the luminaire to the LINE supply wiring inside the junction

box or for products rated 208V, or 240V, connect to the HOT 1

supply wiring.

b. For products rated 120V, 277V or 347V, connect the White lead

from the luminaire to the NEUTRAL supply wiring inside the

junction box or for products rated 208V, or 240V, connect to the

HOT 2 supply wiring.

c. Connect the Green or Green/Yellow lead from the luminaire to the

GROUND supply wiring inside the junction box.

LINE

OR HOT 1

GROUND

LINE-BLACK

GROUND-GREEN

NEUTRAL-WHITE

NEUTRAL

OR HOT 2

SUPPLY WIRING

LUMINAIRE

JUNCTION

BOX

5View of Underneath

Luminaire

(4) Pendant

Mounting

Plate Clips

Luminaire

Slots

(2) Screws

(4) Luminaire Slots

(4) Clips

Pendant

Mounting Plate

Wireform

Cree IG Series Installation guide

Brand: Cree

Model: IG Series

Category: Decorative lighting

Type: Installation guide

Download PDF

report

Cree IG Series Installation guide

Cree IG Series Installation guide

Related papers

Other documents