Technical User Guide 3
DA 174 Winch Motor
Product and Documentation Revision
SKOV A/S reserves the right to change this document and the product herein described without further notice.
In case of doubt, please contact SKOV A/S.
Date of change appears from the back of this manual.
Note
• All rights reserved SKOV A/S. No part of this manual may be reproduced in any manner
whatsoever without the express written permission from SKOV A/S.
• SKOV A/S has made all reasonable efforts to ensure the accuracy of the information contained in
this manual. Should any mistakes or imprecise information occur in spite of this, SKOV A/S would
appreciate being notified thereof.
• Irrespective of the above, SKOV A/S shall not accept any liability with regard to loss or damage
caused or alleged to be caused by reliance on any information contained herein.
• Copyright 2016 by SKOV A/S.
When you start using the product, you should check it for defects or damage (e.g. transport damage). In case of
a defect or damage, please contact SKOV A/S or the nearest distributor.
4 Technical User Guide
DA 174 Winch Motor
1 Product Description................................................................................................. 5
2 Mounting Guide ....................................................................................................... 6
2.1 Positioning the control box ................................................................................................ 6
2.2 Pay attention to scratches .................................................................................................. 6
2.3 Possibilities of installation ................................................................................................. 6
2.4 Centre distance from wall 40mm ....................................................................................... 6
2.5 Centre distance from wall 80mm ....................................................................................... 6
2.6 Straight pull ......................................................................................................................... 7
2.7 Safety ................................................................................................................................... 7
3 Interlinking ............................................................................................................... 7
3.1 DA 1500 ceiling inlet - DA 174/380 mm stepless ............................................................... 7
3.2 DA 1211B wall inlet in ceiling as Combi-Diffuse inlet – DA 174/380 mm ......................... 7
3.3 DA 1200 wall inlet – DA 174/380 mm stepless ................................................................... 7
3.4 Windows – DA 174/380 mm ................................................................................................ 8
3.5 Shutter in outlet – DA 174/380 mm stepless ..................................................................... 8
3.6 Vertical installation ............................................................................................................. 8
3.7 Mechanical reduction of the pulling / slacking length ...................................................... 9
4 Cleaning .................................................................................................................... 9
5 Installation Guide ....................................................................................................10
5.1 Stepless Type - Opens at pull .......................................................................................... 10
5.2 Stepless Type - Opens at Slack ....................................................................................... 11
5.3 ON/OFF Type - Opens at Slack ......................................................................................... 12
6 Technical Data ........................................................................................................13
Technical User Guide 5
DA 174 Winch Motor
1 Product Description
DA 174 is a linear 24 V winch motor for regulation of wall and ceiling inlets in livestock house ventilation
systems.
The typical application is in houses, where it is possible to connect several units to the same winch motor via a
mechanical connection in the form of a pull rod or wire.
DA 174 is mounted directly on the wall and is available in a stepless version.
The control box can be placed as required within 1.8m from the winch motor
DA 174 winch motor complete
Wall fitting
Winch motor
Length of stroke
Eye bolt with
disc and nut
Eye bolt with
discs and nuts
Fitting bolt with
bush and discs
Control box with
wire for motor
Switch
auto/manual
Switch
Forward-0-back
Cable connection
for computer
D
6 Technical User Guide
DA 174 Winch Motor
2 Mounting Guide
Before installation, check the following:
A. Check the house according to drawings as regards positioning
B. Check the part delivery according to order/parts list
2.1 Positioning the control box
Place the control box in appropriate height for
operation and the installed cable.
Mount the cables in the box according to the
wiring chart.
2.2 Pay attention to scratches
Lance and piston are made of anodized
aluminium. Scratches in the surface will result in
corrosion damages.
Retain the piston on the outermost part when
counter tightening.
2.3 Possibilities of installation
The piston/motor must not turn upwards as dirt
and water can penetrate and damage the winch
motor.
2.4 Centre distance from wall 40mm
This installation is e.g. used for operation of
built-in inlets.
2.5 Centre distance from wall 80mm
At operation of flange inlets, more distance is
required.
D
40 mm
80 mm
Technical User Guide 7
DA 174 Winch Motor
2.6 Straight pull
It must be ensured that the winch motor pulls
straight, i.e. equal distance to the centre line.
2.7 Safety
Pull rod and winch motor are connected by
means of a piece of wire of approx. 300 mm.
This must be done to ensure that the inlet can
be opened manually in an emergency situation,
without using tools.
3 Interlinking
When mounting all types of inlets the piston in the winch motor must be pulled completely back.
The inlet must be completely closed when inlets/windows, which open at slack, are connected to
pull rod or wire.
Inlets and flaps, which open at pull, must be completely open when they are connected to pull
rod or wire.
3.1 DA 1500 ceiling inlet - DA 174/380 mm
stepless
Opens at pull.
The piston of the winch motor must be pressed back and
the inlet completely open when they are connected.
Ensure space for max. length of stroke of 380 mm.
Subsequently, the climate computer must be set to open
the inlet 31 cm corresponding to max. opening.
3.2 DA 1211B wall inlet in ceiling as Combi-
Diffuse inlet – DA 174/380 mm
Opens at pull.
The piston of the winch motor must be pressed back and
the inlet completely open when they are connected.
Ensure space for max. length of stroke of 380 mm.
3.3 DA 1200 wall inlet – DA 174/380 mm
stepless
Opens at pull.
The piston of the winch motor must be pressed back and
the inlet completely open when they are connected.
Ensure space for max. length of stroke of 380 mm.
38 cm
31 cm
38cm
38cm
8 Technical User Guide
DA 174 Winch Motor
3.4 Windows – DA 174/380 mm
Opens at slack.
The piston of the winch motor must be pressed back and
the window completely closed when they are connected.
Ensure space for max. length of stroke of 380 mm.
C.f. 3.8 mechanical reduction, if necessary.
3.5 Shutter in outlet – DA 174/380 mm stepless
Opens at pull.
The piston of the winch motor must be pressed home and the
shutters completely open when they are connected.
See item 3.8 mechanical reduction, if necessary.
3.6 Vertical installation
The best positio is a high and vertical position with the
piston downwards as shown. Thus depositing of water and
dirt on the piston is avoided.
380mm
38cm
Technical User Guide 9
DA 174 Winch Motor
3.7 Mechanical reduction of the pulling / slacking length
The length of stroke of the winch motor is sometimes longer than required, i.e. that when the inlets are closed,
the piston can continue further to limit switch e.g. at manual operation. For some inlets, it may be unfavourable
and result in the string falling off the pulleys.
The solution is to mount a safety wire around a mounting bolt including disc. The other end must be fixed on
e.g. the pull rod, so the inlet is just closed.
A corresponding solution with the application of a stop unit mounted directly on wire in connection with the
application of pulleys.
4 Cleaning
Clean the product with water and a brush without using:
high-pressure cleaner
solvents
corrosive/caustic agents
10 Technical User Guide
DA 174 Winch Motor
5 Installation Guide
Installation, service and troubleshooting of electrical equipment must be carried out by expert
staff in compliance with applicable national regulations – in Europe, this would be the EN 60204-
1 or other current EU regulations.
A supply isolator must be installed for each motor and power supply to facilitate voltage-free
work on the electrical equipment. The supply isolator is not supplied by SKOV A/S.
5.1 Stepless Type - Opens at pull
The winch motor DA 174 is mounted with a 5-core cable, which is mounted in the terminals R1 and J6 of the
climate computer.
The terminals Y1-8 of the control box must be connected to the terminals of the computer by means of a 7-core
cable according to the set-up of the computer (Show installation).
Check that the 24 V power supply is sufficient, minimum 1.6 A.
Conductor cross section
Cable length metre
Cross section mm2
0 - 69
70 - 99
100 – 164
165 – 265
1.0
1.5
2.5
4.0
J6
6 7 8
1
2
R1
Y
Fig. 01
Collour code
BK---Black
BN---Brown
RD---Red
GN---Green
BU---Blue
VT---purple
WH---White
D
W2
W1
Computer
Control box
DA 174 stepless
NB Please note colour code of the 5-core cable
Technical User Guide 11
DA 174 Winch Motor
5.2 Stepless Type - Opens at Slack
The winch motor DA 174 is mounted with a 5-core cable, which is mounted in the terminals R1 and J6 of the
climate computer.
The terminals Y1-8 of the control box must be connected to the terminals of the computer by means of a 7-core
cable according to the set-up of the computer (Show installation).
Check that the 24 V power supply is sufficient, minimum 1.6 A.
Conductor cross section
Cable length metre
Cross section mm2
0 - 69
70 - 99
100 – 164
165 – 265
1.0
1.5
2.5
4.0
J6
6 7 8
1
2
R1
Y
Fig. 01
Collour code
BK---Black
BN---Brown
RD---Red
GN---Green
BU---Blue
VT---purple
WH---White
D
W2
W1
Computer
Control box
DA 174 stepless
NB Please note colour code of the 5-core cable
12 Technical User Guide
DA 174 Winch Motor
5.3 ON/OFF Type - Opens at Slack
The winch motor DA 174 is mounted with a 2-core cable, which must be mounted in terminal J6 of the control
box.
The terminals Y1-5 of the control box must be connected to the terminals of the computer by means of a 5-core
cable according to the set-up of the computer (Show installation).
Check that the 24 V power supply is sufficient, minimum 1.6 A.
Conductor cross section
Cable length metre
Cross section mm2
0 - 69
70 - 99
100 – 164
165 – 265
1.0
1.5
2.5
4.0
Collour code
BK---Black
BN---Brown
RD---Red
GN---Green
BU---Blue
VT---purple
WH--White
J6
6 7 8
1
2
R1
Y
D
W2
W1
Computer
Control box
DA 174 ON/OFF
Exchange the
two wires if it
must open at
pull.
Technical User Guide 13
DA 174 Winch Motor
6 Technical Data
Winch motor DA 174 24V
380 mm stepless
Operating voltage
24V DC ± 15%
Power consumption
1.6 A
Intermittence
25%
Max. tensile force
100 kg
Temperature, operation
-10 – 55 °C
Running time between limit switches
108 sec.
Pulling length
380mm
Total length, minimum
646mm
Total length, maximum
1066mm
Protection class*
IP X6
Control signal
Stepless
Potentiometer
0-10 k ohm
Control box
Dimensions
H × W × L 260 × 160 × 140
Protection class*
IP X5
*It is assumed that the base is level, i.e. ≤ 1.5 mm difference of height and that the screws of the cover are tightened with min. 200 Ncm.
14 Technical User Guide
DA 174 Winch Motor
EU - Declaration of Conformity
Manufacturer: SKOV A/S
Address: Hedelund 4, DK-7870 Roslev, Denmark
Telephone: +45 72 17 55 55
This declaration of conformity is issued under the sole responsibility of the manufacturer.
Product: DA 174
Type, model: Winch Motor
EU directives: 2014/35/EU (Low Voltage Directive (LVD))
2014/30/EU (Electromagnetic Compatibility (EMC))
2006/42/EC (Directive on Machinery)
Standards: EN 61000-6-2:2005 + AC:2005
EN 61000-6-4:2007 + A1:2011
We declare as manufacturer
that the products meet the requirements of the listed directives and standards.
Location: Hedelund 4, DK-7870 Roslev
Date: 2016.06.08
Jesper Mogensen
CTO
/
