For Product Info
Savant® Five Shade Power Module with Serial Distribution
Quick Reference Guide
SHA-PMOD5G-00 | 009-1844-00 | 190521
Copyright 2019 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
1 of 2
Front View
The shade power module can power and control up to five
shade motors. Each port (Motor 1 - 5) on the front panel can
be wired to a dierent shade motor. Up to three shade pow-
er modules per enclosure is supported.
Serial IN
– When the shade module is the first module in the chain,
connect the J Geiger Wired Controller to the Serial IN
Connection.
Serial OUT
– Connect the Serial OUT port to the Serial IN port of the
shade module that is next in the chain.
See the following sections for more information:
Serial Control Connections
J Geiger Wired Controller to Serial Connection
Connect the 24V DC port to the 24V DC IN port on the J
Geiger Wired Controller (SHA-MGEIGCTRL-00). Refer to the
Shades Installation and Wiring Guide on the Savant Custom-
er Community for wiring information.
NOTE: A PWM-PENC3-00 enclosure is required upon instal-
lation.
When installing a shade power module into the PWM-
PENC3-00 enclosure, use these tabs to align the module into
position. See the Install Shade Modules section.
Box Contents
(1) Five Shade Power Module (SHA-PMOD5G)
(5) 5-pin Screw Down Plug-in Connector (028-0765-xx)
(1) 2-pin Screw Down Plug-in Connector (028-0767-xx)
(1)
/ inch knockout bushing (015-0216-xx)
(1) Shade Motor PS to 120/240V AC Cable (064-0420-30)
(1) Quick Reference Guide (this document)
Specifications
Shade Power Module to Shade Motor Connections
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Power
Input Power 120-240V AC 50/60 Hz
Output Power 24V DC 2A (each motor)
24V DC Port 24V DC 2A
Maximum Wiring Distance (power panel to shade motor)
#14 AWG Max = 200 ft (60.96 m)
#16 AWG Max = 150 ft (45.72 m)
#18 AWG Max = 100 ft (30.48 m)
Minimum Supported Release
Savant OS da Vinci 9.1
Regulatory
RoHS Compliant
Dimensions and Weights
Height 12.35 (31.37 cm)
Width 3.43 in (8.71 cm)
Depth 2.25 in (5.72 cm) - including connectors
Weight
Net: 2.30 lbs (1.04 kg)
Shipping: 3.30 lbs (1.50 kg)
Use the diagram below to connect a shade motor to a Motor <x> port
on each shade module.
B
-
-
A
+
+
G
SHA-W1000 Cable
+
To red wire on shade motor.
— To back wire on shade motor.
A+
To yellow wire on shade motor.
B-
To blue wire on shade motor.
G
No Connection
– For reference purposes, the SHA-W1000 cable available from Sa-
vant is shown in diagram above.
– Dolphin Super B Crimp connectors are recommended when splic-
ing wires.
– Additional wiring diagrams are available in the Shades Installation
and Wiring Guide (009-1532-00) on the Savant Customer Commu-
nity.
SERIAL IN SERIAL OUT
24V DC
End of Bus
Motor 1
Motor 2
Motor 3
Motor 4
Motor 5
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
+
+
A+
B-
G
-
-
B
A
C
D
A
B
C
D
SHA-PMOD5G-00 | 009-1844-00 | 190521
Copyright 2019 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
2 of 2
J Geiger Shade controllers communicate with the shade modules using
a serial protocol. The diagram below shows the pin-out for the cable
that transports the signaling. The image below shows a CAT 5E/6/7
cable and follows the T1/E1 568B standard.
All AC voltage connections should be to a 15 amp circuit breaker.
ELECTRIC SHOCK! The 120/240V AC source power poses an
electrical shock hazard that has the potential to cause serious injury to
installers and end users.
IMPORTANT!
– A licensed electrician is required to make AC electrical connec-
tions to the shade modules. Isolate and turn o power at the main
breaker panel prior to installing any electrical devices.
– For supply, neutral, and ground connections, use only #14 AWG or
larger solid copper wire.
With all shade modules installed, connect the white (neutral), black
(hot), and green (gnd) wires from each module to a 120/240V AC
circuit. Use the diagram for reference.
Each module requires serial signaling from a controller to function.
To get the serial signaling to each shade module, the signaling is
daisy-chained through each module. Refer to diagram below when
making connections.
1. Verify the 120/240V AC feed from circuit breaker is o.
2. Strip approximately 10 inches of the outer jacketing from the elec-
trical cable and insert wires through the electrical clamp installed
in step 6 of the Prep Enclosure section. Tighten clamp.
3. Using the 6-position WAGO connector already mounted to the
green ground wire screwed to the enclosure, connect all the
ground wires together.
4. Using one of the WAGO 6-position push connectors included with
the enclosure, connect all the neutral wires together.
5. Using one of the WAGO 6-position push connectors supplied with
the enclosure, connect all the hot wires together.
6. Position all wires into the AC compartment neatly and reinstall the
AC compartment cover.
7. Apply power by switching the breaker at the circuit breaker box to
the On position.
Prep Enclosure
Refer to the diagram just below these instruction for reference
1. Remove power at the circuit breaker.
2. Remove the lid from enclosure if one is installed.
3. Turn the captive screw on the AC compartment panel counter-
clockwise (CCW) until the screw pops up.
4. Slide the cover up and out away from the enclosure. Put aside.
5. Remove the two WAGO 6 position push connectors that were
shipped in the AC compartment and set aside.
6. Remove one of the electrical knockouts at the bottom of the en-
closure and install a 1/2 inch electrical cable clamp.
7. If not already completed, remove the electrical knockout from
shade module slot 1 and snap a 1/2 inch nylon insulating bushing
in place of knockout. If installing more than one shade module,
repeat step 7 for slots 2 and 3 as required.
J Geiger Wired Controller to Serial Connection
Connect Power
Serial Control Connections
Install Shade Modules
Making Connections
Shade
Module
Slot 1
Slide up and
then out
Shade
Module
Slot 2
Shade
Module
Slot 3
4
3
6
7
1. Remove the shade module(s) and corresponding Shade Motor PS
to 120/240V AC cable(s) from shipping box.
2. Flip shade module over so the power supply is accessible.
3. Plug the Shade Motor PS to 120/240V AC cable into the 2 pin
connector located on the bottom edge of the power supply board.
The connector is keyed to aid installation. See diagram below.
4. Position shade module over the knockout removed in step 7.
5. Insert the wires through the insulated bushing installed in step 7.
6. Slide the tabs on the bottom of the shade module into the slots to
the left and right of the electrical knockout hole.
7. To secure shade module to enclosure, turn the captive screw on
opposite side of shade module clockwise (CW) into the insert in
the chassis.
8. Repeat steps 1 - 8 and install any additional shade modules.
Shade Module Power Supply
Neutral (White)
Hot (Black)
Green (Gnd)
Module
Slot 1
Module
Slot 2
Module
Slot 3
BUSHING
GND
ON PS
GND
ON PS
GND
ON PS
WAG O
CONNECTORS
BUSHING BUSHING
FROM 15 AMP BREAKER
GND
RS485 IN
RS485 OUT
End of Bus
Motor 1
Motor 2
Motor 3
Motor 4
Motor 5
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
RS485 IN
RS485 OUT
End of Bus
Motor 1
Motor 2
Motor 3
Motor 4
Motor 5
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
RS485 IN
RS485 OUT
End of Bus
Motor 1
Motor 2
Motor 3
Motor 4
Motor 5
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
+
A+
B-
G
-
From Controller
– Up to 15 shade motors per controller is supported.
– Use a standard Cat 5E/6/7 cable when making connections be-
tween the Serial IN and OUT ports.
– The End of Bus LED indicates which module is last in the chain.
PIN
PIN
2
1
PIN 3
PIN 4
L (Connector #22)
H (Connector #21)
NC
NC
NC
NC
PIN 5
PIN 6
PIN 7 GND
PIN 8 GND
RJ-45 CONNECTOR
(Gold pins facing up)
PIN 1 PIN 8
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Savant SHA-PMOD5G-00 Reference guide
-
-
-
-
Savant PWM-PENC3-00 Deployment Guide
-
-
-
Savant QP1R30240 Installation guide
-
-
