MULTIPLEX Bottle C02 Controls Bag-In-Box Kit - EI206788 Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Bottle C02 Controls Bag-In-Box Kit - EI206788
Type
Installation guide

This manual is also suitable for

MULTIPLEX Bottle C02 Controls Bag-In-Box Kit - EI206788 The MULTIPLEX Bottle CO2 Controls Bag-In-Box Kit - EI206788 is a versatile and easy-to-use device that can help you to carbonate your beverages quickly and efficiently. With its high-pressure regulator assembly, it can be used with both domestic and international CO2 tanks, making it a great choice for businesses of all sizes.

The kit includes everything you need to get started, including a CO2 control panel, high-pressure regulator assembly, and CO2 gas lines. It is also compatible with the optional CO2 alarm, which can help you to monitor the CO2 pressure and ensure that your beverages are always carbonated to perfection.

MULTIPLEX Bottle C02 Controls Bag-In-Box Kit - EI206788 The MULTIPLEX Bottle CO2 Controls Bag-In-Box Kit - EI206788 is a versatile and easy-to-use device that can help you to carbonate your beverages quickly and efficiently. With its high-pressure regulator assembly, it can be used with both domestic and international CO2 tanks, making it a great choice for businesses of all sizes.

The kit includes everything you need to get started, including a CO2 control panel, high-pressure regulator assembly, and CO2 gas lines. It is also compatible with the optional CO2 alarm, which can help you to monitor the CO2 pressure and ensure that your beverages are always carbonated to perfection.

In accordance with our policy of continuous product development and improvement,
this information is subject to change at any time without notice.
EI206788 Revision A (ARR/SLS) 11/18/96
Manitowoc Beverage Equipment
2100 Future Drive Sellersburg, IN 47172-1868
Tel: 812.246.7000, 800.367.4233 Fax: 812.246.9922
www.manitowocbeverage.com
Foodservice Group
CO2 Gas Line (2) High Pressure
W/Swivel Nut Fittings Regulator Assembly (2)
Control Panel
Equipment Installation Instructions for
CO2 Control Kit
for P.N. 00206788 (Domestic), P.N. 00215757 and P.N.
00217141 (International)
2
EI206788 Revision A (ARR/SLS) 11/18/96
Equipment Installation Instructions
Caution
DO Adhere to all National and Local Plumbing and Electrical Safety Codes.
DO Turn “off” incoming electrical service switches when servicing, installing, or
repairing equipment.
DO Check that all flare fittings on the carbonation tank(s) are tight. This check should be
performed with a wrench to ensure a quality seal.
DO Inspect pressure on Regulators before starting up equipment.
DO Protect eyes when working around refrigerants.
DO Use caution when handling metal surface edges of all equipment.
DO Handle CO2 cylinders and gauges with care — secure cylinders properly against
abrasion.
DO Store CO2 cylinders in well ventilated areas.
DO NOT Store CO2 cylinders in temperature above 125°F (51.7°C) near furnaces, radiator or
sources of heat.
DO NOT Release CO2 gas from old cylinder.
DO NOT Touch Refrigeration lines inside units, some may exceed temperatures of 200°F
(93.3°C).
3
EI206788 Revision A (ARR/SLS) 11/18/96
Equipment Installation Instructions
Installation (see cover illustrations and Figure
1 below)
1. For P.N. 206788, position the CO2 Control Panel on
front of unit or an appropriate mounting surface about
5 ft. (1.5 m) from the beverage syrup supply. Mark the
mounting holes at top and bottom of the panel and
secure the panel with appropriate fasteners.
For P.N. 215757, mount pressure regulator and
changeover valve on unit using four (4) #10-32 x
1
/2
screws. If there is not a place for acceptable mounting
on unit, place components on a mounting surface
about 5 ft. (1.5 m) from syrup supply using template
for hole location.
2. For P.N. 215757, a copper tube must now be attached
from the regulator to the CO2 changeover valve.
3. Route the 20 ft. (6.1 m) line from the pressure regulator
and attach it to the Bag-In-Box pumps.
4. Install the high pressure regulators on the CO2 tanks.
Connect the CO2 gas lines to the high pressure regula-
tors. Attach the opposite ends of these lines to the CO2
changeover valve (see figure 1). Do not turn “on” CO2
tank regulators at this time.
5. Connect the CO2 gas supply line from carbonator tank
to the cross fitting on the control panel changeover
valve assembly.
6. Test the system for leaks by opening the CO
2 tanks
shut-off valves. Allow the system to pressurize. Adjust
the regulators at the CO2 tanks to 90 psi (6.2 bar). Set
the pressure regulator to 60 psi (4.1 bar). Now turn the
CO2 tank valves to the “off” position. The CO2 tank
gauge should remain constant, no drop in pressure. If
the pressure drops, locate the leak and repair it.
7. For export units only connect power cord as follows
(Power cord not supplied):
a. Attach ring terminal supplied to green/yellow
conductor and attach to ground screw pro-
vided (6-32 self threading).
b. Attach 0.250 quick connect to brown wire
and attach to open terminal on pressure switch.
c. Attach blue wire to transformer lead with wire
nut provided.
8. On P.N. 206788 connect CO
2 alarm power cord into
120 volt outlet or connect P.N. 217141 to 220 volt
supply.
Note: The CO2 alarm will sound and illuminate the lamp
when the CO2 pressure drops below 70 psi (4.8 bar) and
shut-off when the pressure is returned to 90 psi (6.2 bar).
Figure 1
To Bag-In-Box
Gas Line to #2
CO2 Tank
Copper Tube
Gas Line
to #1
CO2 Tank
Alarm
(Optional with
P.N. 215757)
Mounting Panel
(Optional with
P.N. 215757)
Pressure
Regulator
CO2 to
Carbonator
(Not supplied
with kits)
Power Cord
(Not furnished
with P.N. 217141)
  • Page 1 1
  • Page 2 2
  • Page 3 3

MULTIPLEX Bottle C02 Controls Bag-In-Box Kit - EI206788 Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Bottle C02 Controls Bag-In-Box Kit - EI206788
Type
Installation guide
This manual is also suitable for

MULTIPLEX Bottle C02 Controls Bag-In-Box Kit - EI206788 The MULTIPLEX Bottle CO2 Controls Bag-In-Box Kit - EI206788 is a versatile and easy-to-use device that can help you to carbonate your beverages quickly and efficiently. With its high-pressure regulator assembly, it can be used with both domestic and international CO2 tanks, making it a great choice for businesses of all sizes.

The kit includes everything you need to get started, including a CO2 control panel, high-pressure regulator assembly, and CO2 gas lines. It is also compatible with the optional CO2 alarm, which can help you to monitor the CO2 pressure and ensure that your beverages are always carbonated to perfection.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents