WamBam Fence VF13001 Installation guide

Type
Installation guide
For more information, contact us at 1 877-778-5733.
1
Each Fence Panel Box
Includes:
This Post & Cap
Not Included
(See note below)
3-Rail Vinyl Ranch Fence (2 Pack)
BOX CONTENTS
Discover the Benefits of WamBam Traditional Vinyl Fence
• Made of durable, low-maintenance white vinyl
• Post design offers architectural character and flexibility when installing fence
• Post design also offers 4-way universal directional capabilities
(you do not need to order end, line, corner or specialized gate posts)
• Limited Lifetime Warranty
PLEASE NOTE:
YOU WILL NEED TO PURCHASE ONE
EXTRA POST & CAP TO COMPLETE
EACH OF YOUR FENCE RUNS
(Extra posts are sold as 2-packs)
• Post Caps (2)
• Rails (6)
3.5in. Stainless Steel Screws (12)
• Posts (2)
.090in. wall thickness
For more information, contact us at 1 877-778-5733.
2
3-Rail Vinyl Ranch Fence (2 Pack)
PRODUCT SPECIFICATIONS
This fence can be trimmed down both in width and
height to accommodate custom applications.
4.5in.
1.5in.
.090in. Wall Thickness
Top View
4.5in.
4.5in.
3.5in. Screw
Ground
2in.
79.5in.
84in.
20.5in.
8in.
8in.
19.5in.
51.5in.
50in.
Horizontal rail spacing can be
adjusted freely to lower heights.
72in.
10in.
Concrete Footing
36in.
For more information, contact us at 1 877-778-5733.
3
3-Rail Vinyl Ranch Fence (2 Pack)
QUICKIE OVERVIEW
• Prior to construction, check with your regulatory agency for special code requirements in your area.
• Contact your utility supplier to locate and mark underground lines before excavation.
• Sketch out the layout of your fence and calculate the number of panels, gates and posts required (order one
extra post & cap to finish each fence run).
Careful planning & measuring of your fence is essential, as moving posts after the concrete sets is extremely difficult.
A
B
10in.
36in.
1 -
Add approximately 18in. of concrete to the bottom of the hole.
2 - Install posts straight and level.
3 - Add more concrete to within 2in. of ground level.
After stringing your fence line, dig your first post hole 10in.
diameter x 36in. deep. Dig your second hole 84in. on center to
your first hole, and so on. Dig only three or four holes at a time
to ensure proper spacing.
In the first fence section, slide 3 rails down
the groove in your posts to the approximate
position as illustrated on page 2
(rail spacing is flexible).
84in. o.c.
D
In the second fence section, slide 3 rails down the groove in your posts to
the approximate position and repeat with any remaining fence sections.
C
79.5in.
Do not overtighten
screws as it will cause
the vinyl to dimple.
E
For more information, contact us at 1 877-778-5733.
4
3-Rail Vinyl Ranch Fence (2 Pack)
Screws must be inserted straight and
into
the correct area of the post/rail as indicated.
Fasten a 3.5 inch screw through the posts into the rails.
F
Repeat in each rail for a total of six per panel.
This will ensure that your
fence rails will never fall out
of your posts like traditional
vinyl fence rails sometimes do.
VERY IMPORTANT
SCREW RAILS TO POSTS
Line up and insert screws
along edge of rounded
corner radius as shown.
TOP
VIEW
WRONG
WRONG
CORRECT
Screw has not been lined up nor inserted into the
post correctly and has missed the rail entirely.
1 - Put a small bead of vinyl glue or weld (purchased separately at hardware store) along the inside of the cap.
2 - Place the glued cap on the vinyl post and allow to set for 5-10 minutes.
For more information, contact us at 1 877-778-5733.
5
3-Rail Vinyl Ranch Fence (2 Pack)
Most yards are relatively level and will allow for a fairly simple installation. If your
yard is steeply pitched, or is very uneven, you may need to either slope, or stair-step
your panels as illustrated below. Post height can be trimmed down as necessary.
GLUE CAPS ON POSTS
Ground
G
Ground
SLOPED
STAIR-STEPPED
Vinyl Weld
21
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

WamBam Fence VF13001 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI