For more information, contact us at 1 877-778-5733.
1
Each Fence Panel Box Includes:
• Post Cap (1)
•
1.25in. Stainless Steel Screws (4)
• Post (1)
• Top Rail (1)
• Picket Caps (13)
•
Pickets
(13)
• Tube of Glue (1)
•
3.5in. Stainless Steel Screws (4)
• Bottom Rail (1)
Sold Separately:
• Post & Cap
.090in. wall thickness
.055in. wall thickness
This Post & Cap
Not Included
(See note on left)
Classic Vinyl Picket Fence
BOX CONTENTS
Discover the Benefits of WamBam Traditional Vinyl Fence
• Made of durable, low-maintenance white vinyl
• Post design offers architectural character and flexibility when installing fence
• Post design also offers 4-way universal directional capabilities
(you do not need to order end, line, corner or specialized gate posts)
• Innovative locking pickets and rails for increased long-term performance
• Symmetrical appearance; same look on each side of the panel
• Limited Lifetime Warranty
7/8in.
3in.
PLEASE NOTE:
YOU WILL NEED TO PURCHASE ONE
EXTRA POST & CAP TO COMPLETE
EACH OF YOUR FENCE RUNS
(Extra posts are sold as 2-packs)
For more information, contact us at 1 877-778-5733.
2
Classic Vinyl Picket Fence
PRODUCT SPECIFICATIONS
This fence can be trimmed down both in width and
height to accommodate custom applications.
2in.
32in.
3.5in.
6in.
3in.
2.9in.
48in.
72in.
79.5in.
22.5in.
4.5in.
1.5in.
3.5in.
1.5in.
.090in. Wall Thickness
4.5in.
Ground
.090in. Wall Thickness
2in.
36in.
10in.
Concrete Footing
Top View
4.5in.
4.5in.
3.5in. Screw
For more information, contact us at 1 877-778-5733.
3
Classic Vinyl Picket Fence
QUICKIE OVERVIEW
• Prior to construction, check with your regulatory agency for special code requirements in your area.
• Contact your utility supplier to locate and mark underground lines before excavation.
• Sketch out the layout of your fence and calculate the number of panels, gates and posts required (order one
extra post & cap to finish each fence run).
•
Careful planning & measuring of your fence is essential, as moving posts after the concrete sets is extremely difficult.
A
B
10in.
36in.
1 -
Add approximately 18in. of concrete to the bottom of the hole.
2 - Install posts straight and level.
3 - Add more concrete to within 2in. of ground level.
After stringing your fence line, dig your first post hole 10in.
diameter x 36in. deep. Dig your second hole 84in. on center to
your first hole, and so on. Dig only three or four holes at a time
to ensure proper spacing.
Slide the bottom rail through the channel
in the post into approximate position
(about 2in. above the ground).
84in. o.c.
Picket end withTABS
are inserted first.
Warning: Pickets once inserted into
bottom rail cannot be removed.
D
Slide the top rail through the channel
in the post into approximate position.
C
Temporary Spacers
Slide pickets through holes in rails.
E
79.5in.
For more information, contact us at 1 877-778-5733.
4
Classic Vinyl Picket Fence
Ground
Most yards are relatively level and will allow for a fairly simple installation.
If your yard is steeply pitched or is very uneven you may need to stair step your panels as illustrated below.
Post heights can be trimmed down as necessary.
F
Slide pickets through holes in rails and fasten four 1.25 inch screws through the middle
of the top rail/pickets (2), and upper cavity of the bottom rail (2) as indicated.
Picket end withTABS
are inserted first.
Warning: Pickets once
inserted into bottom rail
cannot be removed.
Screws must be inserted
into the correct area of the
rails/pickets as indicated.
Glue picket caps onto top of pickets and adjust the height of the fence as necessary.
G
Being able to moderately adjust the height of your fence
to level at this stage is another perk that a WamBam vinyl
fence offers that most traditional vinyl fences do not.
For more information, contact us at 1 877-778-5733.
5
Classic Vinyl Picket Fence
INSTALL PICKET CAPS
For more information, contact us at 1 877-778-5733.
6
Classic Vinyl Picket Fence
Screws must be inserted straight and
into
the correct area of the post/rail as indicated.
Fasten a 3.5 inch screw through the posts into the rails.
G
H
Repeat in each corner for a total of four per panel.
This will ensure that your
fence rails will never fall out
of your posts like traditional
vinyl fence rails sometimes do.
Do not overtighten
screws as it will cause
the vinyl to dimple.
VERY IMPORTANT
SCREW PANELS TO POSTS
Line up and insert screws
along edge of rounded
corner radius as shown.
TOP
VIEW
WRONG
WRONG
CORRECT
Screw has not been lined up nor inserted into the
post correctly and has missed the rail entirely.
For more information, contact us at 1 877-778-5733.
7
Classic Vinyl Picket Fence
CUSTOMIZE YOUR FENCE DESIGN
Use the cutting guide below to trim pickets
to create a custom fence design.
This fence can also be trimmed down both in width
and height to accomodate custom applications.
B
A
C
D
E
F
E
D
C
B
A
A
B
C
D
E
F
44 1/4 in.
42 3/8 in.
40 7/8 in.
39 3/4 in.
38 7/8 in.
38 3/8 in.
A
B
C
D
E
F
38 1/4 in.
40 in.
41 1/2 in.
42 3/4 in.
43 1/2 in.
44 in.
G
38 1/4 in.
G
44 1/4 in.
G
F
B
A
C
D
E
F
E
D
C
B
A
G
F
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WamBam Fence VF13002 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Zippity Outdoor Products ZP19008 Dimensions Guide
-
Weatherables WTR-THDVA42-S6 Operating instructions
-
-
-
-
-
-
-
Weatherables WKR-THDV42-S8 User manual
-
New England Arbors VA20234 Installation guide
