Cooper Lighting VNLW-P-1001-MV-N-W Installation guide

Brand: Cooper Lighting

Model: VNLW-P-1001-MV-N-W

Type: Installation guide

This manual is also suitable for

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Installation Instructions

Model # VNLW-P-1001-MV-N-W

Model # VNLW-P-1001-MV-N-V

Model # VNLW-P-1001-MV-N-LA

NeoSwitch Passive Infrared (PIR) Single Relay

Vacancy Sensing Wall Switch with Night Light

(Neutral Required)

• Readallinstructionsonbothsidesofthis

sheetfirst

• InstallinaccordancewithALLlocalcodes

• Forindooruseonly

General Information

Technology:PassiveInfrared(PIR)

Electrical Ratings:

120VAC:

• Incandescent/Tungsten–Max.load:6.7amps,

800W,50/60Hz

• Fluorescent/Ballast–Max.load:10amps,1200W,

50/60Hz

MotorLoad:¼HP@125VAC

277VAC:

• Fluorescent/Ballast–Max.load:9.8amps,

2700W,50/60Hz

Ballast Compatibility:Compatiblewithmagneticand

electronicballasts

No Minimum Load Requirement

Time Delays:Self-Adjusting,15seconds/test,1,5,15,

20,30minutes,1hour,2hours

Coverage:Majormotion–1000sq.ft.

 Minormotion–300sq.ft.

Operating Environment:

• Temperature:32°F–104°F(0°C–40°C)

• RelativeHumidity:20%to90%Non-condensing

Housing:Durable,injectionmoldedhousing.

PolycarbonateresincomplieswithUL94VO.

Size:

• MountingPlate/StrapDimensions:

4.195"Hx1.732"W(106.553mmx44mm)

• ProductHousingDimensions:2.618"Hx1.752"

Wx1.9"D(66.5mmx44.5mmx48.26mm)

LED Indicators:RedLEDindicatesPIRdetection;

AmberLEDnightlight.

Speciﬁcations

Description

ThePassiveInfrared(PIR)SingleRelayVacancySensingWallSwitchwithNightLightisalightingcontrolandWall

Switchall-in-onethatisusedforenergysavingsandconvenience.

PIR Technology

ThePassiveInfrared(PIR)SingleRelayVacancySensingWallSwitchwithNightLightusesPassiveInfrared(PIR)

sensortechnologiestomonitoraroomforoccupancy.

TheVNLW-P-1001-MV-Nallowsthecontrolofoneloadwithonevacancysensorswitch.

ThelightsareturnedONbypressingtheuniversallyrecognizedlighticonPushbutton.ThelightsstayONaslong

asthesensordetectsmotionintheroom.Whentheroomisvacated,thelightsturnOFFautomaticallyafterapreset

TimeDelayinterval.

A30secondgraceperiodisaddedafterthelightsshutOFFtogivetheoccupanttimetomoveagainincasethe

lightsshutOFF.Thispreventstheoccupantfromhavingtowalk-uptopressthePushbuttontoreactivatethesensor.

ThenightlightactivateswhensensorturnslightsOFF.Thisfeaturecanbedisabled,seeDIPSwitchSettings.

Thesensorincludesself-adaptivetechnologythatcontinuallyadjuststoconditionsbyadjustingsensitivityand

TimeDelayinReal-time.ByadjustingsensitivityandTimeDelayautomatically,thesensorismaximizingthepotential

energysavingsthatareavailableintheparticularapplication.

Location

WheninstallingtheVNLW-P-1001-MV-Ninanewjunctionbox,choosetheswitchlocationcarefullytoprovide

optimumcoverageoftheoccupiedarea.WhenreplacinganexistingWallSwitch,bearinmindthattheremustbeaclear

Line-of-sightbetweenthesensorandtheareatobecovered.AvoidpointingtheVNLW-P-1001-MV-Ndirectlyintothe

hallwaywhereitmaydetectpassers-by.

Installation

TheVNLW-P-1001-MV-Ncanbeinstalledinanystandardsingle

gangbox.Itmaybeinstalledinthesamemannerasanordinary

WallSwitch.

• WiretheVNLW-P-1001-MV-Nasdescribedinthewiringsection.

• MounttheVNLW-P-1001-MV-Ninthejunctionbox.

Wiring

CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned OFF

at the branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used as the main

switch for a fluorescent lighting circuit, the circuit breaker should be marked “SWD.” All installations should be

in compliance with the National Electric Code and all state and local codes.

NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact fluorescent lamps (CFLs) is

shortened by frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the

effects of cycling.

1.MakesurepoweristurnedOFFatthebranchcircuitbreaker.

2.Wireunitsasshowninwiringdiagramsperapplicablevoltagerequirements.

3.MountunittoWallBox.

4.TurnpowerbackONatthebranchcircuitbreakerandwait2minutesfortheunittostabilize.

5.Makenecessaryadjustments.(SeeCheckoutandAdjustmentssection)

6.InstallWallSwitchplate.

LOAD

120/277 VAC

BLACK

BLUE

NEUTRAL

GROUND

GREEN

WHITE

Wiring Diagram 1: 120/277 VAC single level single circuit wiring diagram

Maximum coverage area may

vary somewhat according to room

shape and the presence of obstacles.

Minor Motion, IR

Major Motion, IR

Coverage

TheVNLW-P-1001-MV-Nisdesignedforofficesupto300squarefeet.

P/N 9850-000353-01

LOAD 1

BLACK

BLUE

NEUTRAL

GROUND

GREEN

WHITE

120/277 VAC

BLACK

BLUE

GROUND

GREEN

WHITE

TRAVELER

WIRES

THREE-WAY WIRING DIAGRAM:

LIGHTS WILL TURN OFF, WHEN UNIT THAT WAS TURNED

ON LAST AND/OR DETECTED MOTION LAST TIMES-OUT.

Wiring Diagram 2: 120/277 VAC single level single circuit three-way wiring diagram

CAUTION: If a room is wired for two circuits using two separate hot leads, it is very important to connect only one circuit per

relay. Both circuits must be fed from the same phase.

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Printed in Malaysia

Time Delay Adjustments

PeoplewhoremainverystillforlongperiodsoftimemayneedalongerTimeDelaythanthedefaultsettingof10

minutes.Aslongastheself-adjustingfeatureisenabled,theswitchwillrespondtoeachpairofFalse-offswithnonormal

OFFinbetweenbyalternatelymakingslightadjustmentstoeitherTimeDelay(by2minuteincrements)orsensitivity,so

thereshouldbenoneedformanualadjustment.Ifmanualadjustmentisdesired,refertoTimeDelaysettingsinDIP

Switchlegend.

ResetsensorTimeDelaytofactorysettingsbymovingDIPSwitches1,2,and3down.(IfDIPSwitches1,2,and3are

alreadydown,toggleDIPSwitch1outofitscurrentposition,wait3seconds,andthenbacktoitsoriginalposition)

Night Light

UnitisshippedwithNightLightfeaturedenabled.WhensensorturnsthelightsOFF,NightLightisactivated.Todisablethis

featuremoveDIPSwitch7up.

Override

TheOverridesettingallowsthesensortooperateasaserviceswitchintheunlikelyeventoffailure.

1. MoveDIPSwitch8up.

2.ThePushbuttoncanbeusedtomanuallyturnlightsONorOFF.

PIR Sensitivity

1. PressthePushbuttontoactivatesensor.

. Standindifferentareasoftheroomandwaveyour

hands.

3. IftheRedLEDdoesnotturnON,checkforany

obstructions.

4. Standstillthreetofourfeetawayfromsensorforfive

seconds.LEDshouldnotturnON.

5. IfRedLEDturnsONwithoutmotionorisconstantly

ONadjustPIRsensitivityto50%bymovingDIP

Switch5up.

Field-of-view outside the space

1. AdjustPIRsensitivityto50%bymovingDIPSwitch

5up.

2. Usenon-reflectivetapestripstocovertheportionsof

thesensorlensthatviewoutsidethespace.

Warranties and Limitation of Liability

DIP Switch Settings Troubleshooting

Pleaserefertowww.coopercontrol.comundertheLegalsectionforourtermsandconditions.

Checkout and Adjustment

1 Minute

Auto*

*Self-Adjusts to

10 min. user mode

Time Delay

DIP Switch

Not Used

PIR Sensitivity OverrideNight Light

Not Used

Default =

15 Minutes

20 Minutes

30 Minutes

5 Minutes

DIP Switch Legend

643



















Full

50%







Enable

Disable

Enable

1 Hour

2 Hours

12345678

AdjustmentsshouldbemadewiththeHVACsystemonsothattheinstallerwillbeabletodetecttheeffectof

airflowontheoperationoftheVNLW-P-1001-MV-N.Useonlyinsulatedtoolstomakeadjustments.

Immediatelyafterapplyingpowertothelightingcircuit,waitapproximatelytwominutesfortheswitchtopowerup

andstabilize.



Self-Adjust

Sensorisshippedinself-adjustmode.ThisappliestoTimeDelayandPIRsensitivity.Inpreparationforthe

InstallerTest,theTimeDelayissetto15seconds,afterthesensorisinstalled,poweredONandhasstabilizedthe

unitwillTime-out15secondsafterthelastmotiondetected.Coverageandsensitivitycanbeconfirmedbywatching

theRed(PIR)indicatorLEDonthefrontofthesensor,whilemovingaroundtheroom.

1.WalkaroundtheroomandmonitorLED.

2.Standindifferentpartsoftheroomandwaveyourhands.LEDshouldonlyturnONforonesecondwitheach

motion.(IfLEDdoesnotturnON,gotoInstallerAdjustments–SensitivityAdjustmentSection)

3.Standstillthreetofourfeetawayfromthesensorforfiveseconds.LEDshouldnotturnON.(IfLEDturnsON,

gotoInstallerAdjustments–SensitivityAdjustmentSection)

. Walkoutsidetheroomandwait30secondsforthelightstoturnOFF.(IflightsdonotturnOFFgotoInstaller

AdjustmentsSection)

5.Re-entertheroomandmanuallyactivatethesensor.(IflightsdonotturnONgotoTroubleshootingSection)

6.AtthispointyoucanexittheroomandletthesensorTime-out.WhenthesensorTimes-outandisinactivefor

fiveminutes,theunitwillgotoa10minuteTimeDelayusermodesetting.

Note:

ToplaceintoTestMode,toggleDIPSwitch8outofitscurrentposition,wait3seconds,andthenbackintoitsoriginalposition.

ON/OFF Button

PIR Lens

DIP Switches

Red (PIR) LED

Lens glows amber

when night light is

activated

1, 2, and 3

3 45678

7 and 8

3 456 78

Installer Adjustments

Issue Possible Causes Suggestions

Lights

Will Not

Turn ON

automatically

SensorisinManualONmode

PressPushbutton.IfAutoMode

isdesiredchangeActivationModetoAuto.

SensorwasturnedOFFmanually.IftheSensor

wasturnedOFFmanuallybeforetheTimeDelay

expired,lightswillremainOFFfortheremainder

oftheTimeDelay.

CheckEcoMeterLED,ifLEDisONthisis

anindicationthatthelightswereturnedOFFmanually.

PressthePushbuttontoturnthelightsbackON.

Powerinterruption Checkincomingvoltageand/orwiring.

Lights

Will Not

Turn ON

manually

Powerinterruption Checkincomingvoltageand/orwiring.

If lights will still not turn ON, set sensor to override mode and call Technical Services at 1-800-553-3879

Lights

Will Not

Turn OFF

automatically

Override

MakesuresensorisnotinOverrideMode.

CheckDIPSwitch8tomakesureitisdown.

SelfAdjust

IfsensorisinSelf-AdjustMode.Itmaybe

possiblefortheunittohaveincreasedtheTimeDelayto

a30minutedelay.Ifthelightsdonot

turnOFFafter30minutesfollownextstep.

2hourDelay

MaximumTimeDelayis2hours.CheckDIPSwitches

toverifyDIPSwitchsettings.IflightsdonotturnOFF

atthesetTimeDelay,checknextstep.

PIRactivatedbyheatsourceotherthanoccupant MoveDIPSwitch5up.

Lights

Will Not

Turn OFF

manually

Call

TechnicalServices

If lights will still not turn OFF, call Technical Services at 1-800-553-3879

Cooper Lighting VNLW-P-1001-MV-N-W Installation guide

Brand: Cooper Lighting

Model: VNLW-P-1001-MV-N-W

Type: Installation guide

This manual is also suitable for

Download PDF

report

Cooper Lighting VNLW-P-1001-MV-N-W Installation guide

This manual is also suitable for

Cooper Lighting VNLW-P-1001-MV-N-W Installation guide

Related papers

Other documents