Greengate NeoSwitch - 120/277/347V PIR/Single Level Wall Switch Sensor (Ground Required) Installation guide

Brand: Greengate

Model: NeoSwitch - 120/277/347V PIR/Single Level Wall Switch Sensor (Ground Required)

Type: Installation guide

This manual is also suitable for

ONW-P-1001-MV-LA

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Installation Instructions

Model # ONW-P-1001-MV-W

Model # ONW-P-1001-MV-V

Model # ONW-P-1001-MV-LA

Model # ONW-P-1001-MV-G

Model # ONW-P-1001-MV-B

NeoSwitch Passive Infrared (PIR)

Single Relay Occupancy Sensing Wall Switch

(Ground Required)

• Readallinstructionsonbothsidesofthis

sheetfirst

• InstallinaccordancewithALLlocalcodes

• Forindooruseonly

General Information

Technology:PassiveInfrared(PIR)

Electrical Ratings

120VAC:

• Incandescent/Tungsten–Max.load:6.7amps,

800W,50/60Hz

• Fluorescent/Ballast–Max.load:10amps,1200W,

50/60Hz

MotorLoad:¼HP@125VAC

277VAC:

• Fluorescent/Ballast–Max.load:9.8amps,

2700W,50/60Hz

Ballast Compatibility:Compatiblewithmagneticand

electronicballasts

No Minimum Load Requirement

Time Delays:Self-Adjusting,15seconds/test(10min

Auto),Selectable5,15,30minutes

Coverage:Majormotion–1000sq.ft.

 Minormotion–300sq.ft.

Light Level Sensing:0to200foot-candles

Operating Environment:

• Temperature:32°F–104°F(0°C–40°C)

• RelativeHumidity:20%to90%Non-condensing

Housing:Durable,injectionmoldedhousing.

PolycarbonateresincomplieswithUL94VO.

Size:

• MountingPlate/StrapDimensions:

4.195"Hx1.732"W(106.553mmx44mm)

• ProductHousingDimensions:2.618"Hx1.752"

Wx1.9"D(66.5mmx44.5mmx48.26mm)

LED Indicators:RedLEDindicatesPIRdetection;Green

LEDactsasEcoMeterornightlightlocator.

Speciﬁcations

Description

Coverage

TheONW-P-1001-MVOccupancySensingWallSwitchisaPassiveInfrared(PIR)motionsensinglightingcontrol

andconventionalWallSwitchall-in-one,usedforenergysavingsandconvenience.

PIR Technology

Thesensor’ssegmentedlensdividesthefieldofviewintosensorzones,anddetectsthechangesintemperature

thatarecreatedwhenaperson,orpartofapersonassmallasahand,passesintooroutofasensorzone.

TheONW-P-1001-MVallowsthecontrolofoneloadwithoneoccupancysensorswitch.

ThesensorcanbeconfiguredtoenhanceenergysavingsbysettingtheunitformanualONoperation.

InAutomaticONMode,thelightsturnONautomaticallywhenapersonenterstheroom.InManualONMode,the

lightsareturnedONbypressingtheuniversallyrecognizedlighticonPushbutton.Ineithermode,thelightsstayON

aslongasthesensordetectsmotionintheroom.Whentheroomisvacated,thelightsturnOFFautomaticallyafter

apresetTimeDelayinterval.

Thesensorincludesself-adaptivetechnologythatcontinuallyadjuststoconditionsbyadjustingsensitivityand

TimeDelayinReal-time.ByadjustingsensitivityandTimeDelayautomatically,thesensorismaximizingthepotential

energysavingsthatareavailableintheparticularapplication.

TheEcoMeterprovidesavisualindicatorofenergyusage,increasingenduserawarenessandreminding

individualstotakecontroloftheirlightingtomaximizeenergysavings.

TheDaylightingfeaturepreventslightsfromturningON,whentheroomisadequatelyilluminatedbynaturallight.

Walk-ThroughfeaturemaximizesenergysavingsbynotleavingthelightsONafteramomentaryoccupancy.The

sensorwillswitchthelightsONwhenitdetectsapersonenteringthearea.Ifthesensordoesnotcontinuetodetect

motion20secondsfollowingtheinitialactivation,itwillautomaticallygotoashorter2minuteTimeDelay.

TheONW-P-1001-MVisdesignedforofficesupto300squarefeet.

Location

WheninstallingtheONW-P-1001-MVinanewjunctionbox,choosetheswitchlocationcarefullytoprovide

optimumcoverageoftheoccupiedarea.WhenreplacinganexistingWallSwitch,bearinmindthattheremustbea

clearLine-of-sightbetweenthesensorandtheareatobecovered.AvoidpointingtheONW-P-1001-MVdirectlyintothe

hallwaywhereitmaydetectpassers-by.

EcoMeter Operation

Load 1 EcoMeter LED

OFF ON

ON OFF

Action EcoMeter Benefit

Apersonentersthespaceand

theloadisactivated

OFF

Theareaisvacatedandthe

lightsturnOFFautomatically

100%

Increasedawarenessofenergysavings;

Actsasanightlightlocator

ApersonturnsthelightsOFF

manuallyuponexitinganarea

100%

Increasedawarenessofenergysavingsand

remindsindividualstotakecontroloftheir

lightingforadditionalsavings;Actsasanight

lightlocator

Thedaylightfeatureprevents

thelightsfromautomatically

turningONwhenaperson

entersanarea

100%

Increasedawarenessofenergysavingsand

letsindividualknowthatthedaylighting

featureisworking

Wiring

CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned OFF

at the branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used as the main

switch for a fluorescent lighting circuit, the circuit breaker should be marked “SWD.” All installations should be

in compliance with the National Electric Code and all state and local codes.

NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact fluorescent lamps (CFLs) is

shortened by frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the

effects of cycling.

1.MakesurepoweristurnedOFFatthebranchcircuitbreaker.

2.Wireunitsasshowninwiringdiagramsperapplicablevoltagerequirements.

3.MountunittoWallBox.

4.TurnpowerbackONatthebranchcircuitbreakerandwait2minutesfortheunittostabilize.

5.Makenecessaryadjustments.(SeeCheckoutandAdjustmentssection)

6.InstallWallSwitchplate.

LOAD

120/277 VAC

BLACK

BLUE

NEUTRAL

GROUND

GREEN

Wiring Diagram 1: 120/277 VAC single level single circuit wiring diagram

Installation

TheONW-P-1001-MVcanbeinstalledinanystandardsinglegang

box.ItmaybeinstalledinthesamemannerasanordinaryWallSwitch.



• WiretheONW-P-1001-MVasdescribedinthewiringsection.

• MounttheONW-P-1001-MVinthejunctionbox.

Maximum coverage area may

vary somewhat according to room

shape and the presence of obstacles.

Minor Motion, IR

Major Motion, IR

P/N 9850-000344-01

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Printed in Malaysia

PIR Sensitivity

1. Standindifferentareasoftheroomandwaveyourhands.

2. IftheRedLEDdoesnotturnON,checkforanyobstructions.

3. Standstillthreetofourfeetawayfromsensorforfiveseconds.LEDshouldnotturnON.

4. IfRedLEDturnsONwithoutmotionorisconstantlyONadjustPIRsensitivityto50%bymovingDIPSwitch5up.

Field-of-view outside the space

1. AdjustPIRsensitivityto50%bymovingDIPSwitch5up.

2. Usenon-reflectivetapestripstocovertheportionsofthesensorlensthatviewoutsidethespace.

Daylight Adjustments

ThedaylightingfeaturepreventsthelightsfromturningONwhentheroomisadequately

illuminatedbynaturallight.Ifthereisenoughlightintheroomregardlessofoccupancy,

thesensorwillholdthelightsOFF.Ifthereisnotenoughlightintheroom,thesensorwill

allowthelightstoturnONwhenoccupied.Thesensorwillnotallowthedaylightingfeature

toturntheloadOFFuntilthespaceisvacantorthelightlevelrisesabovethesetpointand

theTimeDelayexpires.WhileinManualActivationMode,ifsomeoneattemptstoturnthe

loadONandthereissufficientdaylightavailablethe

Daylightingfeaturewillholdthelights

OFF.

1. Setthelightlevelwhentheambientlightisatthelevelwherenoartificiallightis

needed.Ifthisfeatureisnotneeded,leavethelightlevelatmaximum(fullyCW).

2. Withtheload(s)ON,putthesensorintoTestMode.ToplaceintoTestMode,toggle

DIPSwitch8outofitscurrentposition,wait3secondsandthenbackintoits

originalposition.

3. SettheLightleveltominimum(fullyCCW).

4. LetthesensorTime-outsolightsareOFF.Enterthespaceandlightsshouldremain

OFF.

5. Makesurenottoblockthesensorfromthedaylightsourceandadjustthelightlevel

potentiometerCWinsmallincrements.(Pause5secondsbetweeneachadjustment).

6. LightswillnotturnONuponoccupancyactivation,whentheambientlightlevelexceedsthedaylightthresholdsetting.

Time Delay Adjustments

Peoplewhoremainverystillforlongperiodsoftimemayneedalonger

TimeDelaythanthedefaultsettingof10minutes.Aslongastheself-

adjustingfeatureisenabled,theswitchwillrespondtoeachpairofFalse-offs

withnonormalOFFinbetween,byalternatelymakingslightadjustmentsto

eitherTimeDelay(by2minuteincrements)orsensitivity,sothereshould

noneedformanualadjustment.Ifmanualadjustmentisdesired,referto

TimeDelaysettingsinDIPSwitchlegend.

ResetsensorTimeDelaytofactorysettingsbymovingDIPSwitches1and

2down.(IfDIPSwitches1and2arealreadydown,toggleDIPSwitch1out

ofitscurrentposition,wait3seconds,andthenbacktoitsoriginalposition).

Override

Theoverridesettingallowsthesensortooperateasaserviceswitchintheunlikelyeventoffailure.

1. MoveDIPSwitch8up.

2. ThePushbuttoncanbeusedtomanuallyturnlightsONorOFF.

Warranties and Limitation of Liability

DIP Switch Settings

Troubleshooting

Pleaserefertowww.coopercontrol.comundertheLegalsectionforourtermsandconditions.

Checkout and Adjustment

120/277 VAC

BLACK

BLUE

NEUTRAL

GROUND

GREEN

LOAD 1

LOAD 2

LOAD 1

BLACK

BLUE

NEUTRAL

THREE-WAY WIRING DIAGRAM:

LIGHTS WILL TURN OFF, WHEN UNIT THAT WAS TURNED ON LAST AND/OR DETECTEDMOTION LAST TIMES-OUT.

GROUND

GREEN

120/277 VAC

BLACK

BLUE

GROUND

GREEN

TRAVELER

WIRES

Wiring Diagram 3: 120/277 VAC single level single circuit three-way wiring diagram

Wiring Diagram 2: 120/277 VAC single level switch dual level wiring using a toggle switch wiring diagram

5 Minutes

Auto*

*Self-Adjusts to

10 min. user mode

Time Delay

DIP Switch

Activation

PIR Sensitivity Override

Relay 1

Not Used

EcoMeter

Walk-Through Mode

Default =

30 Minutes

15 Minutes

DIP Switch Legend





Disable

Enable









Auto

Manual





Full

50%







Enable

Disable

Enable

12345678

AdjustmentsshouldbemadewiththeHVACsystemonsothattheinstallerwillbeabletodetecttheeffectofairflowon

theoperationoftheONW-P-1001-MV.Useonlyinsulatedtoolstomakeadjustments.

Immediatelyafterapplyingpowertothelightingcircuit,waitapproximatelytwominutesfortheswitchtopowerup

andstabilize.

Self-Adjust

Sensorisshippedinself-adjustmode.ThisappliestoTimeDelayandPIRsensitivity.InpreparationfortheInstallerTest,

theTimeDelayissetto15seconds,afterthesensorisinstalled,poweredONandhasstabilized,theunitwillTime-out15

secondsafterthelastmotiondetected.CoverageandsensitivitycanbeconfirmedbywatchingtheRed(PIR)indicatorLED

onthefrontofthesensor,whilemovingaroundtheroom.

1. WalkaroundtheroomandmonitorLEDs.

2. Standindifferentpartsoftheroomandwaveyourhands.

LEDshouldonlyturnONforonesecondwitheachmotion.

(IfLEDdoesnotturnON,gotoInstallerAdjustments–

SensitivityAdjustmentSection)

3. Standstillthreetofourfeetawayfromsensorforfive

seconds.LEDshouldnotturnON.(IfLEDturnsON,goto

InstallerAdjustments–SensitivityAdjustmentssection)

. Walkoutsidetheroomandwait15secondsforthelights

toturnOFF.(IflightsdonotturnOFFgotoInstaller

AdjustmentsSection)

5. Re-entertheroomtoactivatesensor.(Iflightsdonotturn

ONgotoTroubleshootingSection)

6. Atthispointyoucanreattachthepushbuttonandexit

theroom.Whenthesensortimes-outandisOFFforfive

minutes,theunitwillgotoa10minuteTimeDelayuser

modesetting.

Note:

ToplaceintoTestMode,toggleDIPSwitch8outofitscurrentposition,wait3seconds,andthenbackintoitsoriginalposition.

ON/OFF Button

PIR Lens

DIP Switches

Daylight

Sensor Level

Adjustment

Red (PIR)

Detection LEDs

12345678

DIP Switches

1 & 2

Issue Possible Causes Suggestions

Lights

Will Not

Turn ON

automatically

SensorisinManualONmode

PressPushbutton.IfAutoMode

isdesiredchangeActivationModetoAuto.

SensorwasturnedOFFmanually.IftheSensor

wasturnedOFFmanuallybeforetheTimeDelay

expired,lightswillremainOFFfortheremainder

oftheTimeDelay.

CheckEcoMeterLED.IfLEDisONthisis

anindicationthatthelightswereturnedOFFmanually.

PressthePushbuttontoturnthelightsbackON.

DaylightFeatureEnabled

IfalllightsarerequiredtoturnON

adjustdaylightpotentiometer.

Powerinterruption Checkincomingvoltageand/orwiring.

Lights

Will Not

Turn ON

manually

DaylightFeatureEnabled

IfalllightsarerequiredtoturnON

adjustdaylightpotentiometer.

Powerinterruption Checkincomingvoltageand/orwiring.

If lights will still not turn ON, set sensor to override mode and call Technical Services at 1-800-553-3879

Lights

Will Not

Turn OFF

automatically

Override MakesuresensorisnotinOverrideMode(DIPSwitch8up).

Self-Adjust

IfsensorisinSelf-AdjustMode,itmaybepossibleforthe

unittohaveincreasedtheTimeDelaytoa30minutedelay.

IfthelightsdonotturnOFFafter30minutesfollownextstep.

30MinuteDelay

MaximumTimeDelayis30Minutes.CheckDIPSwitches

toverifyDIPSwitchsettings.IflightsdonotturnOFFatthe

set

TimeDelay,checknextstep.

PIRactivatedbyheatsourceotherthanoccupant MoveDIPSwitch5up.

Lights

Will Not

Turn OFF

manually

CallTechnicalServices

If lights will still not turn OFF, call Technical Services at 1-800-553-3879

CAUTION: If a room is wired for two circuits using two separate hot leads, it is very important to connect only

one circuit per relay. Both circuits must be fed from the same phase.

Installer Adjustments

Greengate NeoSwitch - 120/277/347V PIR/Single Level Wall Switch Sensor (Ground Required) Installation guide

Brand: Greengate

Model: NeoSwitch - 120/277/347V PIR/Single Level Wall Switch Sensor (Ground Required)

Greengate NeoSwitch - 120/277/347V PIR/Single Level Wall Switch Sensor (Ground Required) Installation guide

This manual is also suitable for

Greengate NeoSwitch - 120/277/347V PIR/Single Level Wall Switch Sensor (Ground Required) Installation guide

Related papers

Other documents