Cooper Lighting NeoSwitch - Dual Tech/Dual Relay Wall Switch Vacancy Sensor Installation guide

Brand: Cooper Lighting

Model: NeoSwitch - Dual Tech/Dual Relay Wall Switch Vacancy Sensor

Type: Installation guide

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Installation Instructions

General Information

Description

Model # VNW-D-1001-DMV-W

Model # VNW-D-1001-DMV-V

Model # VNW-D-1001-DMV-G

NeoSwitch Dual Technology Dual Relay

Vacancy Sensing Wall Switch

(Ground Required)

• Readallinstructionsonbothsidesofthis

sheetfirst.

• InstallinaccordancewithALLlocalcodes.

• Forindooruseonly.

Technology:PassiveInfrared(PIR)andUltrasonic(US)

Electrical Ratings:

120VAC:

• Incandescent/Tungsten–Max.load:6.7amps,

800W,50/60Hz

• Fluorescent/Ballast–Max.load:10amps,1200W,

50/60Hz

MotorLoad:¼HP@125VAC

277VAC:

• Fluorescent/Ballast–Max.load:9.8amps,

2700W,50/60Hz

Ballast Compatibility:Compatiblewithmagneticand

electronicballasts

No Minimum Load Requirement

Time Delays:Self-Adjusting,15seconds/test(10min

Auto),Selectable5,15,30minutes

Coverage:Majormotion–1000sq.ft.

 Minormotion–300sq.ft.

Light Level Sensing:0to200foot-candles

Operating Environment:

• Temperature:32°F–104°F(0°C–40°C)

• RelativeHumidity:20%to90%non-condensing

Housing:Durable,injectionmoldedhousing.

PolycarbonateresincomplieswithUL94VO.

Size:

• MountingPlate/StrapDimensions:

4.195"Hx1.732"W(106.553mmx44mm)

• ProductHousingDimensions:2.618"Hx1.752"

Wx1.9"D(66.5mmx44.5mmx48.26mm)

LED Indicators:RedLEDindicatesPIRdetection;Green

LEDindicatesUltrasonicdetection.

TheVNW-D-1001-DMVVacancySensingWallSwitchisaPassiveInfrared(PIR)andUltrasonic(US)motion

sensinglightingcontrolandconventionalwallswitchall-in-one,usedforenergysavingsandconvenience.

ThesensorcombinesPIRandUStechnologiestomonitoraroomforoccupancy.

PIR Technology

Thesensor’ssegmentedlensdividesthefieldofviewintosensorzones,anddetectsthechangesintemperature

thatarecreatedwhenaperson,orpartofapersonassmallasahand,passesintooroutofasensorzone.

US Technology

Thesensorproducesalowintensity,inaudiblesound.Itdetectsoccupancyfromchangesintheacousticwaves

causedbymotion,suchasreachingforatelephone,turningapageinabook,walkingintoaroom,turningina

swivelchair,etc.Thesensordoesnotrespondtoaudiblesound.

TheVNW-D-1001-DMVallowsthecontroloftwoseparateloadswithoneoccupancysensorswitch.

ThelightsareturnedONbypressingtheuniversallyrecognizedlighticonpushbutton.ThelightsstayONaslong

asthesensordetectsmotionintheroom.Whentheroomisvacated,thelightsturnOFFautomaticallyafterapreset

timedelayinterval.

Thesensorincludesself-adaptivetechnologythatcontinuallyadjuststoconditions

byadjustingsensitivityandtime

delayinreal-time.Byadjustingsensitivityandtimedelayautomatically,thesensorismaximizingthepotentialenergy

savingsthatareavailableintheparticularapplication.

TheDaylightingfeaturepreventslightsfromturningON,whentheroomisadequatelyilluminatedbynaturallight.

BathroomMode–Whenselected,bathroommodekeepsthesecondrelayONforanadditional8minutes,after

thefirstrelayhasbeenturnedOFF.Combinethiswithchangingthepushbuttontothelight/fangraphicandyounow

havetheuniversallyrecognizedandeasytousebathroomsolution.

RelaySwapOption–Acommonprobleminelectricwiringiswiringthewrongswitchtothewrongload.Thiscan

makecontrolofloadsconfusingtoanenduser.TheRelaySwapoptionsolvestheproblembyallowingtheswitch

buttonsonthefaceoftheunittobeswapped,aftertheunitiswiredandinstalled.

 TheVNW-D-1001-DMVisdesignedforofficesupto300squarefeet.

WheninstallingVNW-D-1001-DMVinanewjunctionbox,choosetheswitchlocationcarefullytoprovideoptimum

coverageoftheoccupiedarea.Whenreplacinganexistingwallswitch,bearinmindthattheremustbeaclearline-of-

sightbetweenthesensorandtheareatobecovered.AvoidpointingtheVNW-D-1001-DMVdirectlyintothehallway

whereitmaydetectpassers-by.

CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned OFF

at the branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used as the main

switch for a fluorescent lighting circuit, the circuit breaker should be marked “SWD.” All installations should be

in compliance with the National Electric Code and all state and local codes.

 NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact fluorescent lamps (CFLs) is

shortened by frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the effects

of cycling.

LOAD 2

LOAD 1

120/277 VAC

BLACK

RED

BLUE

RED

NEUTRAL

GROUND

GREEN

Wiring Diagram 1:

120/277 VAC dual level

single circuit wiring diagram

LOAD 2

LOAD 1

CIRCUIT 1

120/277 VAC

BLACK

RED

BLUE

RED

NEUTRAL

GROUND

GREEN

CIRCUIT 2

120/277 VAC

Wiring Diagram 2:

120/277 VAC dual level

dual circuit wiring diagram

Minor Motion, IR

Major Motion, IR

Maximum coverage area may

vary somewhat according to room

shape and the presence of obstacles.

The NEMA WD 7 Guide and robotic

method were utilized to verify

coverage patterns.

Minor Motion, Ultrasonic

Major Motion, Ultrasonic

P/N 9850-000278-02

Speciﬁcations

LOAD 2

LOAD 1

BLACK

RED

BLUE

RED

NEUTRAL

GROUND

GREEN

120/277 VAC

BLACK

RED

BLUE

RED

GROUND

GREEN

TRAVELER

WIRES

THREE-WAY WIRING DIAGRAM:

LIGHTS WILL TURN OFF, WHEN UNIT THAT WAS TURNED

ON LAST AND/OR DETECTED MOTION LAST TIMES-OUT.

Wiring Diagram 3: 120/277 VAC dual level single circuit three-way wiring diagram

CAUTION: If a room is wired for two circuits using two separate hot leads, it is very important to connect

only one circuit per relay. Both circuits must be fed from the same phase.

Coverage

Location

Installation

Wiring

1.MakesurepoweristurnedOFFatthebranchcircuitbreaker.

2.Wireunitsasshowninwiringdiagramsperapplicablevoltagerequirements.

3.Mountunittowallbox.

4.TurnpowerbackONatthebranchcircuitbreakerandwait2minutesfortheunittostabilize.

5.Makenecessaryadjustments.(SeeCheckoutandAdjustmentssection)

6.Installwallswitchplate.

TheVNW-D-1001-DMVcanbeinstalledinanystandardsinglegangbox.Itmaybe

installedinthesamemannerasanordinarywallswitch.

• WiretheVNW-D-1001-DMVasdescribedinthewiringsection.

• MounttheVNW-D-1001-DMVinthejunctionbox.

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Printed in Malaysia

AdjustmentsshouldbemadewiththeHVACsystemonsothattheinstallerwillbeabletodetecttheeffectof

airflowontheoperationoftheVNW-D-1001-DMV.Useonlyinsulatedtoolstomakeadjustments.

Immediatelyafterapplyingpowertothelightingcircuit,waitapproximatelytwominutesfortheswitchtopowerup

andstabilize.

Self-Adjust

SensorisshippedinSelf-AdjustMode.ThisappliestoTime

Delay,USandPIRsensitivity.InpreparationfortheInstallerTest,

thetimedelayissetto15seconds,afterthesensorisinstalled,

poweredONandhasstabilized,theunitwilltime-out15seconds

afterthelastmotiondetected.Coverageandsensitivitycanbe

confirmedbywatchingtheGreen(US)andRed(PIR)indicatorLEDs

onthefrontofthesensor,whilemovingaroundtheroom.

1.WalkaroundtheroomandmonitorLEDs.

2.Standindifferentpartsoftheroomandwaveyourhands.

LEDsshouldonlyturnONforonesecondwitheachmotion.

(IfLEDdoesnotturnON,gotoInstallerAdjustmentSection)

3.Standstillthreetofourfeetawayfromsensorforfive

seconds.LEDsshouldnotturnON.(IfLEDdoesturnON,go

toInstallerAdjustmentSection)

4.Walkoutsidetheroomandwait15secondsforthelightsto

turn

OFF.(IflightsdonotturnOFFgotoInstallerAdjustmentsSection)

5.Re-entertheroomandmanuallyactivatethesensor.(IflightsdonotturnONgotoTroubleshootingSection)

6.Atthispointyoucanexittheroomandletthesensortime-out.Whenthesensortimes-outandisOFFforfive

minutes,theunitwillgotoa10minuteTimeDelayusermodesetting.

Note:

ToplaceintoTestMode,toggleDIPSwitch12outofitscurrentposition,wait3seconds,andthenbackintoitsoriginalposition.

Sensitivity Adjustments

UltrasonicSensitivity(GreenLED)–Usingasmallflatheadscrew

driverturnthegreenpotentiometersothatthearrowpointsUP.

1.Standindifferentareasoftheroomandwaveyourhands.

2.IftheGreenLEDdoesnotturnON,increasetheUSsensitivityby

turningthegreenpotentiometerclockwiseinsmallincrements.

RepeatStep1.

3.Standstillthreetofourfeetawayfromsensorforfiveseconds.

LEDshouldnotturnON.

4.IfGreenLEDturnsONwithoutmotionorisconstantlyON

decreasetheUSsensitivitybyturninggreenpotentiometer

counter-clockwiseinsmalldecrements.RepeatStep3.

Note:

DoNotadjustsensitivityhigherthannecessary.

5 Minutes

Auto*

*Self-Adjusts to

10 min. user

mode

Time Delay

DIP Switch

Not Used PIR Sensitivity BathroomOverrideRelay SwapDaylighting

Relay 1Relay 2

Maintain Lights On

Default =

30 Minutes

15 Minutes

DIP Switch Legend





Disable

Enable





Disable

Enable





Disable

Enable

643













Full

50%









Either

Both

Disable

Enable





Normal

Swap

12345678910

11 12

Not Used

ON/OFF Buttons

1 & 2

PIR Lens

DIP Switches

Ultrasonic Detection

Daylight

Sensor Level

Adjustment

Ultrasonic

Sensitivity

Adjustment

Red (PIR) & Green (US)

Detection LEDs

PIR Sensitivity

1.Standindifferentareasoftheroomandwaveyourhands.

2.IftheRedLEDdoesnotturnON,checkforanyobstructions.

3.Standstillthreetofourfeetawayfromsensorforfiveseconds.LEDshouldnotturnON.

4.IfRedLEDturnsONwithoutmotionorisconstantlyONadjustPIRsensitivityto50%bymovingDIPSwitch5up.

Field-of-view outside the space

1. AdjustPIRsensitivityto50%bymovingDIPSwitch5up.

2. Usenon-reflectivetapestripstocovertheportionsofthesensorlensthatviewoutsidethespace.

3. AdjustUltrasonicSensitivity.

Daylight Adjustments

TheDaylightingfeaturepreventsthelightsfromturningONwhentheroomisadequatelyilluminatedbynaturallight.Ifthere

isenoughlightintheroomregardlessofoccupancy,thesensorwillholdthelightsOFF.Ifthereisnotenoughlightintheroom,

thesensorwillallowthelightstoturnON.TheDaylightingfeatureallowstheselectionofwhichrelaytocontrolviaDaylighting

(dualloadmodelsonly).ThesensorwillnotallowtheDaylightingfeaturetoturntheloadOFFuntilthespaceisvacantifthe

lightlevelrisesabovethesetpointand

thetimedelayexpires.IfsomeoneattemptstoturntheloadONandthereissufficient

daylightavailabletheDaylightingfeaturewillholdthelightsOFF.

1.Setthelightlevelwhentheambientlightisatthelevel

wherenoartificiallightisneeded.Ifthisfeatureisnot

needed,leavethelightlevelatmaximum(fullyCW).

2.SetDIPSwitches11(Relay1)and/or12(Relay2)for

daylightcontrol.

3.Withtheload(s)ON,putthesensorintoTestMode.To

placeintoTestMode,toggleDIPSwitch12outofits

currentposition,wait3secondsandthenbackintoits

originalposition.

4.SettheLightleveltominimum(fullyCCW).

5.Letthesensortime-outsolightsareOFF.EnterthespaceandlightsshouldremainOFF.

6.MakesurenottoblockthesensorfromthedaylightsourceandadjustthelightlevelpotentiometerCWinsmall

increments.(Pause5secondsbetweeneachadjustment)

7.LightswillnotturnONuponmanualactivation,whentheambientlightlevelexceedsthedaylightthresholdsetting.

Time Delay Adjustments

Peoplewhoremainverystillforlongperiodsoftimemayneedalongertimedelaythanthedefaultsettingof10

minutes.

Aslongastheself-adjustingfeatureisenabled,theswitchwillrespondtoeachpairoffalseoffswithnonormal

offinbetween,byalternatelymakingslightadjustmentsto

eithertimedelay(by2minuteincrements)orsensitivity,so

thereshouldbenoneedformanualadjustment.Ifmanual

adjustmentisdesired,refertoTimeDelaysettingsinDIP

Switchlegend.

ResetsensorTimeDelaytofactorysettingsbymoving

DIPSwitches1and2down.(IfDIPSwitches1and2

arealreadydown,toggleDIPSwitch1outofitscurrent

position,wait3seconds,andthenbacktoitsoriginalposition)

Override

TheOverridesettingallowsthesensortooperateasaserviceswitchintheunlikelyeventoffailure.

1.MoveDIPSwitch8up.

2.ThepushbuttoncanbeusedtomanuallyturnlightsONorOFF.

1 and 2

3456789101112

11 and 12

12345678910

11 12

Issue Possible Causes Suggestions

Lights

Will Not

Turn ON

manually

DaylightFeatureEnabled

IfalllightsarerequiredadjustDIPSwitches

11and12and/ordaylightpotentiometer.

Powerinterruption Checkincomingvoltageand/orwiring.

If lights will still not turn ON, set sensor to override mode and call Technical Services at 1-800-553-3879

Lights

Will Not

Turn OFF

automatically

Override MakesuresensorisnotinOverrideMode(DIPSwitch8up).

Self-Adjust

IfsensorisinSelf-AdjustMode,itmaybepossibleforthe

unittohaveincreasedtheTimeDelaytoa30minutedelay.

IfthelightsdonotturnOFFafter30minutesfollownextstep.

30MinuteDelay

MaximumTimeDelayis30Minutes.CheckDIPSwitches

toverifyDIPSwitchsettings.IflightsdonotturnOFFatthe

setTimeDelay,checknextstep.

UltrasonicSensitivitysetHigh

Lowersensitivitybyturninggreen

potentiometerCCWinsmalldecrements.

PIRactivatedbyheatsourceotherthanoccupant MoveDIPSwitch5up.

Lights

Will Not

Turn OFF

manually

CallTechnicalServices

If lights will still not turn OFF, call Technical Services at 1-800-553-3879

Checkout and Adjustment

DIP Switch Settings

Installer Adjustments

Troubleshooting

Warranties and Limitation of Liability

Pleaserefertowww.coopercontrol.comundertheLegalsectionforourtermsandconditions.

Cooper Lighting NeoSwitch - Dual Tech/Dual Relay Wall Switch Vacancy Sensor Installation guide

Cooper Lighting NeoSwitch - Dual Tech/Dual Relay Wall Switch Vacancy Sensor Installation guide

Cooper Lighting NeoSwitch - Dual Tech/Dual Relay Wall Switch Vacancy Sensor Installation guide

Related papers

Other documents