Cooper Lighting NeoSwitch - 120/277/347V PIR/Dual Relay Wall Switch Sensor (Ground Required) Installation guide

Brand: Cooper Lighting

Model: NeoSwitch - 120/277/347V PIR/Dual Relay Wall Switch Sensor (Ground Required)

Type: Installation guide

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Installation Instructions

NeoSwitch Passive Infrared (PIR)

Dual Relay Occupancy Sensing Wall Switch

(Ground Required)

• Readallinstructionsonbothsidesofthis

sheetfirst

• InstallinaccordancewithALLlocalcodes

• Forindooruseonly

Technology:PassiveInfrared(PIR)

Electrical Ratings:

120VAC:

• Incandescent/Tungsten–

Max.load:6.7amps,800W,50/60Hz

• Fuorescent/Ballast–

Max.load:10amps,1200W,50/60Hz

MotorLoad:¼HP@125VAC

277VAC:

• Fluorescent/Ballast–

Max.load:9.8amps,2700W,50/60Hz

Ballast Compatibility:Compatiblewithmagneticand

electronicballasts

No Minimum Load Requirement

Time Delays:Self-Adjusting,15seconds/test(10min

Auto),Selectable5,15,30minutes

Coverage:Majormotion–1000sq.ft.

Minormotion–300sq.ft.

Light Level Sensing:0to200foot-candles

Operating Environment:

• Temperature:32°F–104°F(0°C–40°C)

• RelativeHumidity:20%to90%Non-condensing

Housing:Durable,injectionmoldedhousing.Polycarbonate

resincomplieswithUL94VO.

Size:

• MountingPlate/StrapDimensions:

4.195"Hx1.732"W(106.553mmx44mm)

• ProductHousingDimensions:

2.618"Hx1.752"Wx1.9"D

(66.5mmx44.5mmx48.26mm)

LED Indicators:RedLEDindicatesPIRdetection;Green

LEDactsasEcoMeterornightlightlocator.

TheONW-P-1001-DMVOccupancySensingWallSwitchisaPassiveInfrared(PIR)motionsensinglightingcontroland

conventionalwallswitchall-in-one,used

forenergysavingsandconvenience.

PIR Technology

Thesensor’ssegmentedlensdividesthefieldofviewintosensorzones,anddetectsthechangesintemperaturethat

arecreatedwhenaperson,orpartofapersonassmallasahand,passesintooroutofasensorzone.

TheONW-P-1001-DMVallowsthecontroloftwoseparateloadswithoneoccupancysensorswitch.

EnergySaverMode–EitherorbothloadsmaybeconfiguredtoturnONmanually.Thedefaultsettingforthesecond

loadisManualON.Thisensuresthewallswitchonlyactivatesoneload.Ifbothloadsareonwhenthesensortimes-out,

onlytheprimaryloadwillbeactivated.IfthelightswereshutOFFmanually,theunitwillactivatetheprimaryloadonly.

InAutomaticONMode,thelightsturnONautomaticallywhenapersonenterstheroom.InManualONMode,thelights

areturnedONbypressingtheuniversallyrecognizedlighticonpushbutton.Ineithermode,thelightsstayONaslongas

thesensordetectsmotionintheroom.Whentheroomisvacated,thelightsturnOFFautomaticallyafterapresettime

delayinterval.

Thesensorincludesself-adaptivetechnologythatcontinuallyadjuststoconditionsby

adjustingsensitivityandtime

delayinreal-time.Byadjustingsensitivityandtimedelayautomatically,thesensorismaximizingthepotentialenergy

savingsthatareavailableintheparticularapplication.

TheEcoMeterprovidesavisualindicatorofenergyusage,increasingenduserawarenessandremindingindividualsto

takecontroloftheirlightingtomaximizeenergysavings.

TheDaylightingfeaturepreventslightsfromturningON,whentheroomisadequatelyilluminatedbynaturallight.

Walk-ThroughfeaturemaximizesenergysavingsbynotleavingthelightsONafteramomentaryoccupancy.Thesensor

willswitchthelightsONwhenitdetectsapersonenteringthearea.Ifthesensordoesnotcontinuetodetectmotion20

secondsfollowingtheinitialactivation,itwillautomaticallygotoashorter2minutetimedelay.

BathroomMode–Whenselected,bathroommodekeepsthesecondrelayONforanadditional8minutes,afterthe

firstrelayhasbeenturnedO FF.Combinethiswithchangingthepushbuttontothelight/fangraphicandyounowhavethe

universallyrecognizedandeasytousebathroomsolution.

RelaySwapOption–Acommonprobleminelectricwiringiswiringthewrongswitchtothewrongload.Thiscanmake

controlofloadsconfusingto

anenduser.TheRelaySwapoptionsolvestheproblembyallowingtheswitchbuttonsonthe

faceoftheunittobeswapped,aftertheunitiswiredandinstalled.

TheONW-P-1001-DMVisdesignedforofficesupto300squarefeet.

WheninstallingtheONW-P-1001-DMVinanewjunctionbox,choosetheswitchlocationcarefullytoprovideoptimum

coverageoftheoccupiedarea.Whenreplacinganexistingwallswitch,bearinmindthattheremustbeaclearline-of-sight

betweenthesensorandtheareatobecovered.AvoidpointingtheONW-P-1001-DMVdirectlyintothehallwaywhereitmay

detectpassers-by.

EcoMeter Operation

Load 1 Load 2 EcoMeter LED

OFF OFF 100%

ON OFF 50%

OFF ON 50%

ON ON OFF

Action EcoMeter Beneﬁt

Apersonentersthespaceand

oneoftheloadsisactivated

50% Increasedawarenessofenergysavings

BothloadsareON OFF

Theareaisvacatedandthe

lightsturnOFFautomatically

100%

Increasedawarenessofenergysavings;

Actsasanightlightlocator

ApersonturnsthelightsOFF

manuallyuponexitinganarea

100%

Increasedawarenessofenergy

savingsandremindsindividualstotake

controloftheirlightingforadditional

savings;Actsasanightlightlocator

IftheDaylightingfunctionis

activatedforoneofthetwoloads

andthereissufficientdaylightinthe

space,theunitwillholdthatloadOFF

50%

Increasedawarenessofenergy

savings;Letspersonsknowthatthe

daylightsensorisholdingthelightsOFF;

Actsasanightlightlocator

IftheDaylightingfunctionis

activatedforbothloadsandthereis

sufficientdaylightinthespace,the

unitwillholdthatloadsOFF

100%

Increasedawarenessofenergy

savings;Letspersonsknowthatthe

daylightsensorisholdingthelightsOFF;

Actsasanightlightlocator

CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned OFF at

the branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used as the main switch

for a ﬂuorescent lighting circuit, the circuit breaker should be marked “SWD.” All installations should be in

compliance with the National Electric Code and all state and local codes.

NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact fluorescent lamps (CFLs) is shortened

by frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the effects of cycling.

1. MakesurepoweristurnedOFFatthebranchcircuitbreaker.

2.Wireunitsasshown

inwiringdiagramsperapplicablevoltagerequirements.

3.Mountunittowallbox.

4. TurnpowerbackONatthebranchcircuitbreakerandwait2minutesfortheunittostabilize.

5.Makenecessaryadjustments.(SeeCheckoutandAdjustmentssection)

6.Installwallswitchplate.

LOAD 2

LOAD 1

120/277 VAC

BLACK

RED

BLUE

RED

NEUTRAL

GROUND

GREEN

Wiring Diagram 1: 120/277 VAC dual level single circuit wiring diagram

TheONW-P-1001-DMVcanbeinstalledinanystandardsinglegangbox.Itmaybe

installedinthesamemannerasanordinarywallswitch.

• WiretheONW-P-1001-DMVasdescribedinthewiringsection

• MounttheONW-P-1001-DMVinthejunctionbox

Maximum coverage area may

vary somewhat according to room

shape and the presence of obstacles.

Minor Motion, IR

Major Motion, IR

Coverage Description

Speciﬁcations

General Information

Location

Installation

Wiring

Model # ONW-P-1001-DMV-W

Model # ONW-P-1001-DMV-V

Model # ONW-P-1001-DMV-LA

Model # ONW-P-1001-DMV-G

Model # ONW-P-1001-DMV-B

P/N 9850-000341-01

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Printed in Malaysia

PIR Sensitivity

1. Standindifferentareasoftheroomandwaveyourhands.

2.IftheRedLEDdoesnotturnON,checkforanyobstructions.

3.Standstillthreetofourfeetawayfromsensorforveseconds.LEDshouldnotturnON.

4. IfRedLEDturnsONwithoutmotionorisconstantlyonadjustPIRsensitivityto50%bymovingDIPSwitch5up.

Field-of-view outside the space

1. AdjustPIRsensitivityto50%bymovingDIPSwitch5up.

2.Usenon-reectivetapestripstocovertheportionsofthesensorlensthatviewoutsidethespace.

Daylight Adjustments

TheDaylightingfeaturepreventsthelightsfromturningONwhen

theroomisadequatelyilluminatedbynaturallight.Ifthereisenough

lightintheroomregardlessofoccupancy,thesensorwillholdthe

lightsOFF.Ifthereisnotenoughlightintheroom,thesensorwill

allowthelightstoturnONwhenoccupied.TheDaylightingfeature

allowstheselectionofwhichrelaytocontrolviadaylighting(dualload

modelsonly).ThesensorwillnotallowtheDaylightingfeaturetoturn

theloadOFFuntilthespaceisvacantifthelightlevelrisesabovethe

setpointandthetimedelayexpires.WhileinManualActivationMode,

ifsomeoneattemptstoturntheloadONandthereissufcientdaylightavailabletheDaylightingfeaturewillholdthelightsOF F.

1. Setthelightlevelwhentheambientlightisatthelevelwherenoartificiallightisneeded.Ifthisfeatureisnotneeded,

leavethelightlevelatmaximum(fullyCW).

2.SetDIPSwitches11(Relay1)and/or12(Relay2)fordaylightcontrol.

3.Withtheload(s)ON,putthesensorintoTestMode.ToplaceintoTestMode,toggleDIPSwitch12outofitscurrent

position,wait3secondsandthenbackintoitsoriginalposition.

4. Setthelightleveltominimum(fullyCCW).

5.Letthesensortime-outsolightsareOF F.EnterthespaceandlightsshouldremainOF F.

6.MakesurenottoblockthesensorfromthedaylightsourceandadjustthelightlevelpotentiometerCWinsmall

increments.(Pause5secondsbetweeneachadjustment)

7. LightswillnotturnONuponoccupancyactivation,whentheambientlightlevelexceedsthedaylightthresholdsetting.

Time Delay Adjustments

Peoplewhoremainverystillforlongperiodsoftimemayneed

alongertimedelaythanthedefaultsettingof10minutes.Aslong

astheself-adjustingfeatureisenabled,theswitchwillrespond

toeachpairoffalse-OFFswithnonormalOFFinbetween,by

alternatelymakingslightadjustmentstoeithertimedelay(by2minute

increments)orsensitivity,sothereshouldbenoneedformanual

adjustment.Ifmanualadjustmentisdesired,refertoTimeDelay

settingsinDIPSwitchlegend.

ResetsensortimedelaytofactorysettingsbymovingDIPSwitches

1and2down.(IfDIPSwitches1and2arealreadydown,toggleDIP

Switch1outofitscurrentposition,wait3seconds,andthenbackto

itsoriginalposition)

Pleaserefertowww.coopercontrol.comundertheLegalsectionforourtermsandconditions.

1. WalkaroundtheroomandmonitorLEDs.

2. Standindifferentpartsoftheroomandwaveyourhands.

LEDshouldonlyturnONforonesecondwitheachmotion.

(IfLEDdoesnotturnON,gotoInstallerAdjustments–

SensitivityAdjustmentSection)

3. Standstillthreetofourfeetawayfromsensorforve

seconds.LEDshouldnotturnON.(IfLEDturnsON,goto

InstallerAdjustments–SensitivityAdjustmentssection)

4. Walkoutsidetheroomandwait15secondsforthe

lightstoturnOFF.(IflightsdonotturnOFFgotoInstaller

Adjustments

Section)

5. Re-entertheroomtoactivatesensor.(Iflightsdonotturn

ONgotoTroubleshootingSection)

6. Atthispointyoucanexittheroomandletthesensortime-

out.Whenthesensortimes-outandisinactiveforve

minutes,theunitwillgotoa10minutetimedelayuser

modesetting.

Note:ToplaceintoTestMode,toggleDIPSwitch12outofitscurrent

position,wait3seconds,andthenbackintoitsoriginalposition.

LOAD 2

LOAD 1

BLACK

RED

BLUE

RED

NEUTRAL (CIRCUIT 1)

NEUTRAL (CIRCUIT 2)

GROUND

CIRCUIT 1

GREEN

CIRCUIT 1

120/277 VAC

CIRCUIT 2

120/277 VAC

LOAD 2

LOAD 1

BLACK

RED

BLUE

RED

NEUTRAL

THREE-WAY WIRING DIAGRAM:

LIGHTS WILL TURN OFF, WHEN UNIT THAT WAS TURNED ON LAST AND/OR DETECTED MOTION LAST TIMES-OUT

GROUND

GREEN

120/277 VAC

BLACK

RED

BLUE

RED

GROUND

GREEN

TRAVELER

WIRES

Wiring Diagram 3: 120/277 VAC dual level single circuit three-way wiring diagram

Wiring Diagram 2: 120/277 VAC dual level dual circuit wiring diagram

CAUTION: If a room is wired for two circuits using two separate hot leads, it is very important to connect only one circuit

per relay. Both circuits must be fed from the same phase.

Issue Possible Causes Suggestions

Lights

Will Not

Turn ON

automatically

SensorisinManualONmode

Presspushbutton.IfAutoMode

isdesiredchangeActivationModetoAuto.

SensorwasturnedOFFmanually.Ifthe

SensorwasturnedOFFmanuallybefore

thetimedelayexpired,lightswillremain

OFFfortheremainderofthetimedelay.

CheckEcoMeterLED.IfLEDisONthisisan

indicationthatthelightswereturnedOFFmanually.

PressthepushbuttontoturnthelightsbackON.

DaylightingFeatureEnabled

IfalllightsarerequiredtoturnONadjust

DIPSwitches11and12and/ordaylightpotentiometer.

Powerinterruption Checkincomingvoltageand/orwiring.

Lights

Will Not

Turn ON

manually

DaylightingFeatureEnabled

IfalllightsarerequiredadjustDIPSwitches

11and12and/ordaylightpotentiometer.

Powerinterruption Checkincomingvoltageand/orwiring.

If lights will still not turn ON, set sensor to override mode and call Technical Services at 1-800-553-3879

Lights

Will Not

Turn OFF

automatically

Override MakesuresensorisnotinOverrideMode(DIPSwitch8up).

Self-Adjust

IfsensorisinSelf-AdjustMode,itmaybepossibleforthe

unittohaveincreasedthetimedelaytoa30minutedelay.

IfthelightsdonotturnOFFafter30minutesfollownextstep.

30MinuteDelay

Maximumtimedelayis30Minutes.CheckDIP

SwitchestoverifyDIPSwitchsettings.Iflightsdo

not

turnOFFatthesettimedelay,checknextstep.

PIRactivatedbyheatsourceotherthanoccupant MoveDIPSwitch5up.

Lights

Will Not

Turn OFF

manually

CallTechnicalServices

If lights will still not turn OFF, call Technical Services at 1-800-553-3879

5 Minutes

Auto*

*Self-Adjusts to

10 min. user

mode

Time Delay

DIP Switch

Activation PIR Sensitivity EcoMeterBathroom Relay SwapDaylighting

Relay 1Relay 2Relay 1 Relay 2

OverrideWalk-Through Mode

Default =

30 Minutes

15 Minutes

DIP Switch Legend





Disable

Enable





Disable

Enable





Disable

Enable





Disable

Enable





Auto

Manual









Auto

Manual





Full

50%





Disable

Enable





Enable

Disable





Normal

Swap

12345678910

11 12

EcoMeter

ON/OFF Buttons

1 & 2

PIR Lens

DIP Switches

Daylight

Sensor Level

Adjustment

Red (PIR)

Detection LED

11 and 12

12345678910

11 12

34567891011

1 and

AdjustmentsshouldbemadewiththeHVACsystemONsothattheinstallerwillbeabletodetecttheeffectofairowon

theoperationoftheONW-P-1001-DMV.Useonlyinsulatedtoolstomakeadjustments.

Immediatelyafterapplyingpowertothelightingcircuit,waitapproximatelytwominutesfortheswitchtopower-up

andstabilize.

Self-Adjust

Sensorisshippedinself-adjustmode.ThisappliestotimedelayandPIRsensitivity.InpreparationfortheInstallerTest,

thetimedelayissetto15seconds,afterthesensorisinstalled,poweredONandhasstabilized,theunitwilltime-out15

secondsafterthelastmotiondetected.CoverageandsensitivitycanbeconrmedbywatchingtheRed(PIR)indicatorLED

onthefrontofthesensor,whilemovingaroundtheroom.

Override

TheOverridesettingallowsthesensortooperateasaserviceswitchintheunlikelyeventoffailure.

1. MoveDIPSwitch8up.

2.ThepushbuttoncanbeusedtomanuallyturnlightsONorOFF.

Checkout and Adjustment

DIP Switch Settings

Installer Adjustments

Troubleshooting

Warranties and Limitation of Liability

Cooper Lighting NeoSwitch - 120/277/347V PIR/Dual Relay Wall Switch Sensor (Ground Required) Installation guide

Brand: Cooper Lighting

Model: NeoSwitch - 120/277/347V PIR/Dual Relay Wall Switch Sensor (Ground Required)

Type: Installation guide

Download PDF

report

Cooper Lighting NeoSwitch - 120/277/347V PIR/Dual Relay Wall Switch Sensor (Ground Required) Installation guide

Cooper Lighting NeoSwitch - 120/277/347V PIR/Dual Relay Wall Switch Sensor (Ground Required) Installation guide

Related papers

Other documents