2. Computers & electronics
  3. Computer cables
  4. Signal cables
  5. Adp
  6. 700

Adp 700 Setup Manual

  • Hello! I am an AI chatbot trained to assist you with the Adp 700 Setup Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
ADP ezLaborManager Visual Reference Card
ADP 700 Timeclock Setup
1
K.E./M.D./S.M. © 2014 by ADP, LLC
ADP 700 Timeclock Setup
Setting up and Wiring an ADP 700 Timeclock
1. If you indicated on the order form that you intended to use an Ethernet connection; the contents of
your timeclock boxes should contain:
A. ADP 700 Timeclock
B. Power Supply
C. Using a Finger Scanner instructions
D. ADP 700 Quick Start Guide
E. ADP 700 Installation and Setup Guide
F. Mounting hardware
G. 6 ft. Ethernet cable
A
B
C
D & E
F
G
ADP ezLaborManager Visual Reference Card
ADP 700 Timeclock Setup
2
K.E./M.D./S.M. © 2014 by ADP, LLC
ADP 700 Timeclock Setup
2. If you indicated on the order form that you intended to use a Direct serial connection; the contents of your
timeclock boxes should contain:
A. ADP 700 Timeclock
B. Power Supply
C. Using a Finger Scanner instructions
D. ADP 700 Quick Start Guide
E. ADP 700 Installation and Setup Guide
F. Mounting hardware
G. 6 ft. Ethernet cable
H. 50 ft. Direct cable (or longer if so indicated on the order form)
I. RJ11/DB9 adapter
J. Keyspan USB-Serial adapter
A
B
C
D & E
F
G
H
I
J
ADP ezLaborManager Visual Reference Card
ADP 700 Timeclock Setup
3
K.E./M.D./S.M. © 2014 by ADP, LLC
ADP 700 Timeclock Setup
3. Unscrew the thumbscrew on the left side of the timeclock. The screw should NOT come out, it should just be
loose.
ADP ezLaborManager Visual Reference Card
ADP 700 Timeclock Setup
4
K.E./M.D./S.M. © 2014 by ADP, LLC
ADP 700 Timeclock Setup
4. Unlock the terminal with one of the provided keys and then gently pull the top of the timeclock towards you
while you hold the back plate by inserting a finger into the round hole. The front plate will swing forward on its
hinges.
ADP ezLaborManager Visual Reference Card
ADP 700 Timeclock Setup
5
K.E./M.D./S.M. © 2014 by ADP, LLC
ADP 700 Timeclock Setup
5. The back plate and inside of the timeclock will look like the photo below.
Serial Jack
ADP ezLaborManager Visual Reference Card
ADP 700 Timeclock Setup
6
K.E./M.D./S.M. © 2014 by ADP, LLC
ADP 700 Timeclock Setup
6. If using an Ethernet connection, hook up the cables like the photo below. Slightly tighten the zip tie so the power
cable can’t be unplugged by pulling on it.
Zip Tie
ADP ezLaborManager Visual Reference Card
ADP 700 Timeclock Setup
7
K.E./M.D./S.M. © 2014 by ADP, LLC
ADP 700 Timeclock Setup
7. If using the Direct timeclock, connect the white CAT 3 cable (this is not a phone cable) into the serial jack in the
timeclock. Then connect the gray RJ11 adapter to the white cable and finally the black Keyspan USB cable to the
gray RJ11 adapter. Plug the black Keyspan USB cable into a USB port in your computer.
Zip Tie
/