Keyspan USA-19H User manual

Brand: Keyspan

Model: USA-19H

Category: Interface hubs

Type: User manual

This manual is also suitable for

USB 4-Port

Table of Contents

•

Introduction

•

Capabilities

•

Installation Instructions

•

Configuring Your Serial Device

•

Keyspan Serial Assistant

•

Problem Solving

•

Appendices

•

Frequently Asked Questions (FAQs)

•

Compatibility List for Windows

•

Configuration Examples for Windows

•

Serial Port Pin Outs

•

LED Behavior

•

TX Ack Advance

•

Notices

•

Keyspan Warranty Information

•

Support Information

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 1

1.1 - Introduction

Looking for a way to connect your serial devices to a USB port on your USB equipped Windows

computer? The

Keyspan USB Serial Adapter

is a simple, inexpensive, and reliable way to make

this connection.

The Adapter plugs into any USB port on your PC. It provides one DB9 serial port which can be

used to connect to your Palm Organizer, WindowsCE device, Wacom tablet, and many other serial

devices.

Multiple Keyspan USB Serial Adapters may be installed on one CPU if desired.

Requirements

The

Keyspan USB Serial Adapter Software for Windows

requires the following:

• Windows

•

At least one available USB port

•

Windows 98 / 98 SE / 98 Me / 2000 / XP

Contents

The

Keyspan USB Serial Adapter

package includes:

•

Keyspan USB Serial Adapter (USA-19H)

• USB cable

•

Mac and Windows compatible CD with software and user manual

Note: This documentation applies to Keyspan's USB Serial Adapter

Software for Windows and covers the features and use of this software

on that platform. For information and instructions for this product on

other platforms, please visit Keyspan's web page

<http://www.keyspan.com>.

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 2

2.1 - Capabilities

The Keyspan USB Serial Adapter provides

one male DB9 serial port

which supports RS-232

asynchronous communications at

data rates up to 230 Kbps

. Please read our

Compatibility List for Windows

for a list of serial devices that have been tested with the Keyspan

USB Serial Adapter.

Keyspan USB Serial Adapter Port

Keyspan USB Serial Adapter

Serial Port

The DB9 port on the Keyspan Adapter is seen as a COM port by Windows. The Keyspan COM

port is interfaced via the "Win32 Communications API" and is then available to any program that

accesses COM ports via this API.

By default, the COM port number assigned to the Keyspan adapter is the first unassigned

(available) COM port number in the Windows registry. For example, if COM1 and COM2 have

already been assigned or set aside by any software or hardware, the Keyspan adapter will take the

next COM port (COM3). This COM port number can then be accessed via your serial device's

software (ie Palm's HotSync Manager, Wacom tablet control panel, etc.)

Note: You can connect more than one Keyspan USB Serial Adapter to

your USB equipped Windows computer. The DB9 ports on subsequent

adapters will have a different COM port numbers.

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 3

3.1 - Installation Instructions

Installing the USB Serial Adapter Software for Windows

Operating Systems

Note:

These instructions apply to installing the Keyspan USB Serial

Adapter on Windows. If you are installing this software on other

platforms, please read the

Keyspan USB Serial Software User

Manual

for that platform.

Step 1

Insert the Keyspan Serial Adapter CD-ROM

Turn your computer ON. When your computer starts up, place the Keyspan USB Serial Adapter

CD into the CD-ROM drive.

This will open the Keyspan USB Serial Adapter

CD browser

(Note: you can manually start the

browser

by locating and running the "

Launch.exe

" program on the CD-ROM).

Step 2

Run the Keyspan USB Serial Software for Windows Installer

If the Keyspan Adapter is connected to your computer,

disconnect

it now.

Once the Keyspan CD browser has opened, click on the "

Install Software

" selection and then

click on the "

Install Keyspan USA19H Software

" selection. This will start the software installer.

Follow the instructions on-screen to complete the installation.

Step 3

Software Installation Complete!

Now that you have installed the Keyspan USB Serial Adapter software, you are ready to install the

Keyspan USB Serial Adapter hardware. Please proceed to the

nstalling the Keyspan USB

Serial Adapter Hardware

instructions.

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 4

Installing the Keyspan USB Serial Adapter Hardware

The following hardware installation instructions provide a basic overview on installing the

Keyspan

USB Serial Adapter

in a USB port. For detailed instructions on how to connect USB devices

your specific computer, please refer to the USB Device Install section in your computer's user's

manual.

Step 4

- Connect the USB cable to the Adapter (if necessary)

If your Keyspan adapter does not have an attached USB cable, attach the included USB cable into

the Keyspan adapter's USB port.

Step 5

Connect the Adapter to your USB port

Attach the Adapter to your computer by connecting the Adapter's USB cable into any built-in USB

port on your computer or USB Hub. It is not necessary to turn off your computer when attaching

the Adapter.

Step 6

- Hardware Installation Complete!

Your Keyspan USB Serial Adapter is ready for use now that you have installed hardware and

software.

Please proceed to the

Configuring Your Serial Device

section in this manual for instructions on

what to do next.

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 5

4.1 - Configuring Your Serial Device

Prior to using your serial device (modem,UPS, etc.) with the Keyspan USB Serial Adapter, you

must:

connect your serial device (

hardware

) to the Keyspan port

configure your serial device's

software

to use the Keyspan port

The following instructions provide a general overview of this process however we do provide

specific configuration instructions for certain serial devices. For a list of these examples, please

read the

Configuration Examples for Windows

Appendix in this manual.

Connecting Your Serial Device (Hardware)

If your Keyspan adapter is not connected, please do so NOW.

Step 1

Connect Your Serial Device To The Keyspan Adapter

Attach your serial device's (ie Palm cradle, GPS, cell phone) serial cable to the serial port on your

Keyspan USB Serial Adapter.

Step 2

Determine Which Keyspan Port Your Serial Device Is Connected To

If your have a Keyspan product that has more than one serial port, please note which Keyspan

serial port your serial device is connected to (the serial port on the Keyspan product, not your USB

ports on your computer or USB hub). This information will become useful as we start

Configuring

Your Serial Device's Software

Configuring Your Serial Device's Software

The following configuration instructions provide a basic overview of how to configure your

software to use your Keyspan serial port(s). For specific instructions on how to operate your serial

device, please refer to your serial device's user's manual for detailed instructions...

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 6

Step 3

Check the Keyspan Serial Assistant

Now that your serial device is connected to the Keyspan adapter, you should check to see if the

Keyspan serial port is installed correctly.

To do this, open the

Keyspan Serial Assistant

(in

Start

menu ->

Programs

Keyspan USB

Serial Adapter

Keyspan Serial Assistant

)

. When you open the

Keyspan Serial Assistant

, you will see the following window:

the

Keyspan Serial Assistant

window

If your Keyspan hardware and software are installed correctly, you will see your adapter in the

Adapter Status

' tab box. You should also see the

COM port number (ie COM1, COM2

, etc.)

and the COM Port Status.(IDLE or BUSY).

The COM port number and its COM port Status

message are

very important

to configuring

your serial device.

The COM port Status

is the state of the Keyspan serial port. All serial ports have two states,

BUSY (aka "In Use") or IDLE (aka "

Available

"). When serial port is IDLE

, the port is

available

for use by any serial device's software. When a COM port is

BUSY

, the serial port is

in use by

software and therefore

not available

to other programs.

The COM port number

is the address of the Keyspan serial port. In order for any serial device to

communicate via the Keyspan adapter, that serial device's software must be told to use the Keyspan

COM port number.

If you see your COM port number and its COM port Status

, proceed to

Step 4. If you do not

see either of these items, proceed

Problem Solving

section in this manual.

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 7

Step 4

Determine Where To Select/Configure The Keyspan Serial Port(s)

Prior to using your serial device with a Keyspan serial port, you must first tell that serial device's

software

which serial port your serial device

hardware

is connected to.

For example, if you have a Palm, you will have to tell the Palm Desktop

software to look for your

Palm handheld (

hardware

) on a Keyspan serial port. By doing this, you establish communication

between your serial device's

software

(ie the Palm Desktop software) and your serial device

hardware (the Palm handheld unit).

Most serial devices will have software that will allow you to select which serial port the device is

connected to. Depending on your serial device and its software, you may have to configure: a

Control Panel (ie modems accessing ISPs), an application (ie UPSes), or some combination of

these (ie modems accessing terminals using Zterm).

Please refer to your serial devices documentation on which method your serial device uses and how

to access that software's serial port "configuration" screen.

Once you've determined where to select or configure your serial device's software's serial port

settings, please proceed to

Step 5.

Step 5

Determine Which Serial Port To Select In Your Serial Device's Software

When you've found the port selection screen in your serial device's software, you may be presented

with a list of COM port numbers, a place to type in a COM port number, or some combination of

both.

At this point, you have to select or enter COM port number of the Keyspan serial adapter you are

connecting to. Please note that you can see the COM port number in the

Adapter Status

tab in

the

Keyspan Serial Assistant

Step 6

Use Your Serial Device

Once you've configured your serial software to use the Keyspan serial port, you're ready to start

using your serial device under Windows.

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 8

5.1 - Keyspan Serial Assistant

Besides the required drivers, the Keyspan USB Serial Adapter software installer installs an

application called

Keyspan Serial Assistant

. This application is used to:

•

Determine the status of the adapter software and hardware

•

Assist in problem solving

Launching the Keyspan Serial Assistant

To launch the Assistant, open the

Keyspan Serial Assistant

(in

Start

menu ->

Programs

Keyspan USB Serial Adapter

Keyspan Serial Assistant

)

. When you open the

Keyspan Serial Assistant

, you will see the following window:

the

Keyspan Serial Assistant

window

If your Keyspan hardware and software are installed correctly, you will see your adapter in the

Adapter Status

' tab box. You should also see the

COM port number (ie COM1, COM2

, etc.)

and the COM Port Status.(IDLE or BUSY).

If you see your COM port number and its COM port Status

. If you do not see either of these

items, proceed

Problem Solving

section in this manual.

Explanation of Assistant Features

The following is a description of all the relevant text boxes and menus found in the Keyspan Serial

Assistant. You can also obtain this information by turning on the '

Enable

Tool Tips

' check box in

the Help

tab in the Assistant window.

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 9

Adapter Status Tab

the

Adapter Status

tab

The

Adapter Status

tab in the Keyspan Serial Assistant displays the status of your Keyspan

adapter. Specifically, it shows

the COM port number (ie COM1, COM2

, etc.) and the

COM Port

Status.(IDLE or BUSY).

If you have several Keyspan adapters of the same type, they will all show

up in this tab.

This is also the first place to check to see if your Keyspan adapter is working properly. If your

Keyspan adapter does not show up in the

Adapter Status

tab,

please proceed

Problem Solving

section in this manual for further instructions.

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 10

Properties Tab

the

Properties

tab

The Properties

tab in the Keyspan Serial Assistant allows you

test

your Keyspan adapter and

make changes to the behavior

of the Keyspan adapter. The following is an explanation of the

items in this tab.

the

Adapter

pull down menu

The Adapter

pull down menu is used to select which USB Serial Adapter you would like to

configure. If you only have one Keyspan USB Serial Adapter, you will not need to change the

selection.

the

Endpoints

radio buttons

The

Endpoints

radio buttons are used to configure how the Keyspan adapter will communicate

with the USB subsystem (software)on your computer. Most users will not need to modify the

default setting (Compatible (Interrupt)). You should only change this setting if you are sure that

your serial device needs a specific setting. The default setting is

Compatible

(Interrupt).

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 11

the

Port

pull down

If you have more than one serial port on your Keyspan adapter, the

Port

pull down menu allows

you select which serial port you want to modify or test. You can also see the serial port's

COM

port number and its COM port status

next to the

Port

pull down menu. If you only have one

serial port on your Keyspan USB Serial Adapter, you will not need to change the selection.

The

Test This Port

button

The Test This Port

button tests the COM port selected in the

Port

pull down menu. The test that

is performed is the selected test in the

Test Option box.

the

Test Mode

box

The Test Mode

box allows to specify the type of test that will be performed when you press the

Test This Port button.

There are 3 types of tests:

TX Only

: Use this test to test only the transmit (Tx) signals of the Keyspan adapter.

Ext. LoopBack

: Use this test sending and receiving data. This test sends data out the selected serial

port and waits to receive it via a special Loopback connector. You can find more information about

this special Loopback connector in the

Serial Port Pin Outs

section in this manual.

Int. Loop Back

: Use this test sending and receiving data. This test is performed within the Keyspan

adapter hardware. This test DOES NOT require a special Loopback cable.

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 12

the

Test Typ

e box

The Test Typ

e box allows to specify how many times the selected test will be repeated when you

press the Test button. Use the

Quick

option to perform the test once. To perform a subsequent test,

press the Test This Port button. Use the Continuous

option to repeat the test continuously. To

stop the test, press the

Stop Test

button (the

Test This Port

button becomes the

Stop Test button

during a test).

the

Test Speed

pull down menu

The Test Speed

pull down menu allows to specify the speed (baud rate) at which the port will be

tested at when you press the

Test This Port

button button.

the

Test Status

box reports

The

Test Status

box reports the test status or results of the selected COM port.

the

Receive FIFO Buffer Size

pull down menu

The Receive FIFO Buffer Size

pull down

menu allows you to configure the number of characters

which are stored in the card's "

First In First O

ut" input buffer ("FIFO") before they are made

available to the computer. The default value of this parameter is "16". The

Receive FIFO

improves

the reliability of data transfer at high speeds. You can turn this option OFF for perform

ance

reasons however this is not necessary in most cases.

the

Update Configuration

button

The

Update Configuration

button updates the Keyspan adapter with the changes you have made

in the Properties tab

. Please note that these changes will take effect when you click the

Update

Configuration

button.

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 13

Port Mapping Tab

the

Port Mapping

tab

The Port Mapping

tab in the Keyspan Serial Assistant allows you to change how COM port

numbers are assigned to your Keyspan adapter. The following is an explanation of the items in this

tab.

Important!!! Please make sure you read this entire section. Changing

COM port assignments may render other hardware unusable.

the

COM Port List

box

The COM Port List

box shows any connected

Keyspan USB Serial Adapter

, its

COM port

number and COM port status

. You can also see any other COM port that have been assigned or

reserved on your computer if you enable or check the

Show All COM Assignment

check box.

the

Show All COM Assignments

check box

Enable or check the

Show All COM Assignments

check box to display ALL of the COM port

name and numbers that have been registered on your computer. This will include COM ports for

other devices.

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 14

Note: You may have COM ports assigned or 'set aside' for hardware that

may not be installed on your computer depending on how your computer

was setup by its manufacturer.

the

COM port mapping

pull down menu

The

COM port mapping

pull down menu allows you to reassign the selected Keyspan COM port

in the

COM port list

window. This window also reports whether a COM port is '

in use'. In this

menu, '

in use

' means that the selected COM port has assigned or reserved. It is

highly

recommended

that you only change the COM port mapping to COM ports that are not '

in use'.

Note: The

COM port mapping

pull down menu allows you to change

the COM port mapping to any COM port including those that have

already been assigned (aka

in use

). Changing the COM port mapping to

a COM port that is

in use

may render any hardware and/or software

using that port inoperable.

the

Adapter Port Mapping Mode

box

The Adapter Port Mapping Mode

box allows you to change the behavior of how Keyspan COM

port numbers are assigned when you connect the Keyspan adapter to a different USB port than the

one it was originally connected to.

Dynamic

assigns a COM port number (or numbers if your Keyspan adapter has multiple serial

ports) to a particular Keyspan adapter. If you disconnect the Keyspan adapter and connect it to a

different USB port, the COM port number of that Keyspan adapter will

not change

. This is the

default setting

and is recommended setting if you only have one Keyspan adapter.

Geographic

assigns a COM port number (or numbers if your Keyspan adapter has multiple serial

ports) to a particular USB port on your computer. If you disconnect the Keyspan adapter and

connect it to a different USB port, the COM port number of that Keyspan adapter

will change

This setting is recommended if you are using multiple Keyspan adapters and want the COM port

numbers to remain the same.

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 15

the

Delete All Keyspan USB Serial Adapter Port Mappings

button

The

Delete All Keyspan USB Serial Adapter Port Mappings

button clears the Windows

registry of all Keyspan USB Serial Adapter

COM port numbers

and Keyspan USB information.

This allows Windows to create new COM port assignments.

Note: that this is an option for advanced users only. If you are unsure

about how this command will affect your computer, please contact

Keyspan Tech Support

for further assistance.

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 16

Diagnostics Tab

the

Diagnostics

tab

The

Diagnostic

tab in the Keyspan Serial Assistant reports diagnostic information about your

Keyspan adapter's software and hardware. This information is useful if you are trying to solve

problems with Keyspan's technical support staff. The following is an explanation of the items in

this tab.

the Adapter Status/Error log

Log Window

The Adapter Status / Error Events

box displays the status of your Keyspan adapter hardware

and software. It detects if the Keyspan driver is installed and whether or not a Keyspan adapter is

connected.

the

Clear Log Window

button

The

Clear Log Window

button will clear the

Adapter Status / Error Events box.

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 17

the

Log Debug Events

check box

Enable or check the

Log Debug Events

check box to display all of the Keyspan adapter's debug

events as well as the driver events. This option can be turned on and off.

the

Open Driver Events Window

button

The

Open Driver Events Window

button will open the Keyspan adapter's Event log window.

This window reports all of the events or actions that the adapter is performing. This is useful in

troubleshooting data communication problems.

the

Open Data Monitor Window

button

The

Open Data Monitor Window

button will open the Keyspan adapter's Line Monitor (aka

Data Monitor) window. The Line Monitor will display all data and all modem control state changes

sent to and from the USB Serial Adapter.

(continued on next page...)

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 18

Help Tab

the

Help

tab

The Help

tab in the Keyspan Serial Assistant displays the version numbers if the different

components in your Keyspan USB Serial Adapter installation. You can also enable

Tool Tips

(on

screen help), read your Keyspan adapter's User's Manual, or go to Keyspan's home page.

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 19

6.1 - Problem Solving

If you are having problems with your

Keyspan USB to Serial Adapter in Windows

, please read

the following instructions to assist you in troubleshooting your Keyspan adapter.

Hardware Troubleshooting

Step 1

Use the Keyspan Serial Assistant

Launch the

Keyspan Serial Assistant

application. When you open the

Keyspan Serial Assistant

application, the '

Adapter Status

' tab will show your Keyspan adapter, its

COM port number (ie

COM1, COM2

, etc.) and its

COM Port Status.(IDLE or BUSY).

If you do not receive either of these messages, please contact

Keyspan Tech Support

for further

assistance.

Otherwise, skip ahead to

Step 2.

Software/Serial Device Troubleshooting

Step 2

- Check The Physical Connections

Make certain that your serial device is powered on and is properly connected to the Keyspan Serial

Adapter.

Proceed to Step 3 ...

Step 3

- Check Your Serial Device's Software Configuration

Check to see if your serial device's software is configured to use the Keyspan port . Please refer to

your serial device's documentation for instructions on how to select/switch/configure a serial port in

that software.

Once you've found your software port configuration screen, does it display the Keyspan USB

Serial Adapter

COM port number?

If you do not see the Keyspan COM port number

please contact

Keyspan Tech Support

for

further assistance.

Keyspan:USB Serial Adapter for Windows-v3.4 Manual

This User Manual applies to the Keyspan USB Serial Adapter Software for

Windows

Rev 03jul13 Page 20

Page is loading ...

Keyspan USA-19H User manual

Brand: Keyspan

Model: USA-19H

Category: Interface hubs

Type: User manual

This manual is also suitable for

USB 4-Port

Download PDF

report

Keyspan USA-19H User manual

This manual is also suitable for

Keyspan USA-19H User manual

Related papers

Other documents