2. PacLights
  3. FHMA
FHMA

PacLights FHMA Installation guide

  • Hello! I am an AI chatbot trained to assist you with the PacLights FHMA Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION GUIDE FHMA Series LED High Mast Light
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved Page 1 of 3
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL-INST-FHMA-v0
FHMA INITIAL SET-UP
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:
• Make certain power is OFF before installing or maintaining fi xture. No user serviceable parts inside.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened fi rmly. Apply weatherproof silicone
sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and
unused conduit entries.
FIG. 1
OPTIONAL PHOTOCELL SENSOR
FIG. 2
FHMA-200/300 FHMA-450/500 FHMA-600/750
Install the Shorting Cap on the (7 pin NEMA) Receptacle correctly.
Install the Shorting Cap (provided) by carefully pressing down into the
socket and twisting CW (Fig. 1). Note: If Photocell Sensor is provided
see the following for instructions.
Connect the ACL and the ACN from the FHMA Fixture to the conduit with the AC power Supply Cable. Follow the Wiring Diagram provided.
AC POWER SUPPLY
FHMA DRIVER
GRAY (-)
PURPLE (+)
HOT [BLACK]
NEUTRAL [WHITE]
GROUND [GREEN]
WIRING DIAGRAM
DIM
INPUT
SHORTING CAP
The Twist-Lock Photocell Sensor can be easily installed on all FHMA
Receptacles. Install the Photocell Sensor provided by carefully
pressing down into the socket and twisting CW (Fig. 2). Note: If
the Photocell Sensor is not included this step can be skipped. If the
Photocell Sensor is included prior to fi eld installation the Initial Set-Up
can be skipped.
PHOTOCELL
SENSOR
FHMA FIXTURE
RECEPTACLE
12
RECEPTACLE
INSTALLATION GUIDE FHMA Series LED High Mast Light
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved Page 2 of 3
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL-INST-FHMA-v0
OPTIONAL DIMMING FUNCTION
The Optional Dimming Function is available for select models of the
FHMA Series. Loosen the Driver Cover Screws (2) at the side of the
Driver Box (Fig. 3).
1
FIG. 3
SCREWS
Lift the Driver Cover for access inside the Driver Box (Fig. 4).
2
FIG. 4
The input power and light output of the FHMA fi xture can be
adjusted by simply turning the Dial from 1 to 8 (Fig. 5). (8 = full
output, 1 is the minimum output. Output range: 25%, 40%, 50%,
60%, 70%, 80%, 90%, 100%, factory setting ‘8’)
3
FIG. 5
FHMA FIXTURE
DIAL
DRIVER BOX
DIAL
SURGE
PROTECTOR
DRIVERS
The FHMA fi xture can be mounted to most standard Roadway Arms.
The 4-Bolt Mount Brackets supplied fi ts 1-1/4” to 2” nominal Pipe
Arms. Loosen the bolts or remove if needed. Install the FHMA
fi xture onto the Pipe Arm (Fig. 6).
1
ROADWAY ARM MOUNTING
FIG. 6
2
FIG. 8
PIPE ARM
3
VERTICAL
ADJUSTMENT
FIG. 7
PIPE ARM
SUPPORT
WASHERS
BOLTS
MOUNT BRACKETS
With the Vertical Adjustments, set the angle, then fasten the Bolts
to secure the Mount Brackets to the Pipe Arm in place to the FHMA
fi xture (Fig. 8).
PIPE ARM
BOLTS
MOUNT BRACKETS
WASHERS
The FHMA fi xtures have Vertical Adjustments inside that allow the
fi xture to be tilted at angles up to 5°. Use the Level to install the
fi xture level (Fig. 7).
LOCK WASHERS
LOCK WASHERS
LEVEL
FIG. 9
4The FHMA fi xture in a typical setting with a Light Post and a Roadway
Upsweep Arm (Fig. 9).
UPSWEEP
ARM
LIGHTPOST
FHMA FIXTURE
DRIVER
COVER
DRIVER COVER
DRIVER BOX
INSTALLATION GUIDE FHMA Series LED High Mast Light
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved Page 3 of 3
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL-INST-FHMA-v0
1The Optional Glare Shield can help to limit light trespass. Align the
Glare Shield to the holes around the inside of the Module Base and
fasten with the Screws (Fig. 12).
OPTIONAL GLARE SHIELD
2The Glare Shield can be installed as needed on the fi xture to limit light
trespass (Fig. 13a & 13b).
FIG. 12
FIG. 13a
GLARE
SHIELD
SCREWS
FHMA FIXTURE
MODULES
FIG. 13b
MODULE PROJECTION ADJUSTMENT
The direction of the Module light projection of the FHMA fi xture can
be adjusted. Loosen the Screws (3) of the FHMA fi xture (Fig. 10).
1
FIG. 10
SCREWS
FHMA FIXTURE
MODULE BASE
The FHMA fi xture can now be adjusted by rotating the Module Base
(up to 165° left or right) (Fig. 11). When the desired direction is
reached tighten the Screws.
2
FIG. 11 MODULE
MODULE BASE
MODULE BASE
/