2. PacLights
  3. RKTN-22D30
RKTN-22D30

PacLights RKTN-22D30 Installation guide

  • Hello! I've reviewed the installation guide for the PacLights RKTN series LED Troffer Retrofit fixtures, specifically models RKTN 22D30, RKTN 24D45, and RKTN 14D30. This guide includes important safety instructions, mounting procedures, wiring diagrams, and details on optional PIR/Daylight sensors and Bluetooth controls. I'm ready to assist you with any questions about installation, sensor setup, or system reset.
  • What should I do before installing the fixture?
    How do I install the PIR sensor?
    How can I decommission the fixture from a Network Zone manually?
INSTALLATION GUIDE RKTN Series LED Tro er Retrofi t
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2022 PacLights All Rights Reserved Page 1 of 2
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL_INST_RKTN_v0
The RKTN Series are Bluetooth Network Control enabled. Remove the
Sensor Cover (Fig. 1). Install the PIR Sensor to the RKTN fi xture by
attaching the Connector to the PIR Sensor and press into place on the
RKTN fi xture (Fig. 2).
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:
• Make certain power is OFF before installing or maintaining fi xture. No user serviceable parts inside.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened fi rmly. Apply weatherproof silicone
sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and
unused conduit entries.
FIG. 1 FIG. 2
RKTN - 22D30 RKTN - 24D45 RKTN - 14D30
Connect the ACL and the ACN from the RKTN Fixture to the conduit with the AC power Supply Cable. Follow the Wiring Diagram provided.
AC POWER SUPPLY
RKTN DRIVER
HOT [BLACK]
NEUTRAL [WHITE]
GROUND [GREEN]
WIRING DIAGRAM
INPUT
RKTN FIXTURE
RKTN FIXTURE
A RKTN fi xture can be de-commissioned from any Network Zone manually
by ‘long pressing’ for 5 seconds the ‘Reset’ Button that is located on the
Bluetooth Driver on top of the RKTN fi xture Panel (Fig. 3). The ‘Reset’
Button is located at the end of the Bluetooth Driver between the Wire
Connectors (Fig. 4).
RESET / DECOMMISSION
PIR/DAYLIGHT SENSOR (OPTIONAL)
SENSOR COVER
CONNECTOR
PIR SENSOR FIG. 3 FIG. 4
CONNECTORS
DRIVER
‘RESET’
BUTTON
INSTALLATION GUIDE RKTN Series LED Tro er Retrofi t
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2022 PacLights All Rights Reserved Page 2 of 2
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL_INST_RKTN_v0
Prior to installation, shut o the power to the existing fi xture.
Remove components from the hosting fi xture that includes the host
fi xture lamp(s), ballast cover, ballast, brackets, lamp holders and
wiring. Leave supply and grounding leads
(Fig. 5).
1
RKTN MOUNTING ONTO A T-GRID
T-GRID
EXISTING
HOUSING
Lift and install the LED panel End Brackets to each end of the
existing Housing (Fig. 6). Fasten the End Brackets with Screws to the
Housing (Fig. 7).
2
FIG. 5
FIG. 6
If a gap between the fi xture and T-Grid is too large, then the Side
Bracket can be installed (Fig. 8). Insert each Tab End into each of the
Slots of the End Brackets (Fig. 9).
RKTN FIXTURE HINGE
SIDE BRACKET
3
FIG. 8
END BRACKET
5
FIG. 12
SAFETY CABLES
RKTN FIXTURE
Rotate the RKTN fi xture on its Hinge up towards the End Brackets
and T-Grid (Fig. 13).
6
Rotate both Locking Latches upwards into the slots of the End
Brackets (Fig. 14 & 15).
7
FIG. 13
FIG. 14
SUPPLY WIRES
RKTN FIXTURE
LOCKING LATCHES
RKTN FIXTURE
END BRACKETS
Align the RKTN fi xture Hinges into the Keyholes/Slots of the End
Brackets (Fig 10). Insert and slide into place along the Keyhole/Slot
(Fig 11).
4
COMPONENTS
FIG. 10 KEYHOLE / SLOT
SCREW
Hook the Safety Cables into the existing Housing. Attach the Power
Supply Wires (Fig. 12). Please refer to the wiring diagram.
FIG. 15
EXISTING
HOUSING T-GRID
LOCKING LATCH
RKTN FIXTURE
T-GRID
END BRACKET SLOT
FIG. 7
FIG. 9
SLOT
END BRACKET
TAB END
FIG. 11
SIDE BRACKET
RKTN FIXTURE
END BRACKET
/