2. PacLights
  3. FTFN – 22D35 Center Basket LED Troffer
FTFN – 22D35 Center Basket LED Troffer

PacLights FTFN – 22D35 Center Basket LED Troffer Installation guide

  • Hello! I've reviewed the PacLights FTFN series LED Troffer installation guide. This document provides instructions for installing FTFN-22D35, FTFN-24D45 and FTFN-14D30 models and covers T-Grid, surface, suspended and drywall recessed mounting options, wiring details, and Bluetooth network control setup. I'm ready to assist you with any questions you may have about the document or the installation process.
  • How do I decommission a FTFN fixture from a Network Zone?
    Where is the 'Reset' button located?
    What should I do to ensure proper weatherproofing?
INSTALLATION GUIDE FTFN Center Basket LED Tro er
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2022 PacLights All Rights Reserved Page 1 of 3
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL_INST_FTFN_v0
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:
• Make certain power is OFF before installing or maintaining fi xture. No user serviceable parts inside.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened fi rmly. Apply weatherproof silicone
sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and
unused conduit entries.
FIG. 3 FIG. 4
FTFN - 22D35 FTFN - 24D45 FTFN - 14D30
SCREWS
CONNECTORS
Connect the ACL and the ACN from the FTFN Fixture to the conduit with the AC power Supply Cable. Follow the Wiring Diagram provided.
AC POWER SUPPLY
FTFN DRIVER
HOT [BLACK]
NEUTRAL [WHITE]
GROUND [GREEN]
WIRING DIAGRAM
INPUT
FTFN FIXTURE
BLUETOOTH MESH NETWORKED CONTROL &
ENABLED DRIVER
A FTFN fi xture can be de-commissioned from any Network Zone manually
by ‘long pressing’ for 5 seconds the ‘Reset’ Button that is located on the
Bluetooth Driver inside the FTFN fi xture Panel. Remove the screws (2)
and slide then lift the fi xture Panel Cover (Fig. 3). The ‘Reset’ Button is
located at the end of the Bluetooth Driver between the Wire Connectors
(Fig. 4).
‘RESET’
BUTTON
DRIVER
PANEL
COVER
FTFN FIXTURE
NETWORK LIGHTING CONTROLS (NLC)
SENSOR COVER
FTFN FIXTURE
PIR SENSOR
CONNECTOR
All models of FTFN are Bluetooth Network Conrol enabled. Remove
the Sensor Cover (Fig. 1). Install the PIR Sensor to the FTFN fi xture by
attaching the Connector to the PIR Sensor and press into place on the
FTFN fi xture (Fig. 2).
FIG. 1 FIG. 2
INSTALLATION GUIDE FTFN Center Basket LED Tro er
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2022 PacLights All Rights Reserved Page 2 of 3
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL_INST_FTFN_v0
The FTFN fi xture has Mounting Tabs at all four corners each with holes
that can be used for Suspended Mounting. Place the Aircraft Cable at
all (4) Mounting Tabs and secure in place as needed (Fig. 11).
1
FTFN MOUNTING ONTO A T-GRID
T-GRID
Now with the four tabs set into position the FTFN fi xture is ready to
lay onto the T-Grid (Fig. 7).
3
FIG. 5
FIG. 7
To clear corners for ceiling tile, bend tabs fl ush against the T-Grid.
Use a sheet metal Screw to fasten fi xture to the T-Grid (Fig. 8).
SAFETY CABLE
4
FIG. 8
6
FIG. 10
SUPPLY CABLE
Use a Safety Cable (hanger wire) to ‘tie-o ’ at the Tabs (Screws and
Hanger Wires supplied by others) (Fig. 9).
5
FTFN FIXTURE
FIG. 9
MOUNTING TAB
TIE OFF
Run a Power Supply Cable through a Conduit and install all wiring
connections inside the Panel Cover of the FTFN fi xture. Attach the
wiring access Cover Plate. Please see wiring instructions (Fig. 10).
Refer to the wiring diagram.
SCREWDRIVER
CONDUIT
FTFN FIXTURE
T-GRID
COVER PLATE
FTFN FIXTURE
MOUNTING TAB
FTFN FIXTURE
PANEL COVER
T-GRID
If needed, use metal Shears/Cutters to carefully adjust each Mounting
Tab to the proper height of the T-Grid (Fig. 6).
2
FIG. 6
T-GRID
MOUNTING TAB
FTFN FIXTURE
SHEARS/CUTTERS
SCREW
MOUNTING TAB
OPTIONAL FTFN SUSPENDED MOUNT
FIG. 11
The FTFN fi xture has Mounting Tabs at all four corners. Carefully
bend out (4) Mounting Tabs to 90° on all four corners to fi t onto the
T-Grid (Fig. 5).
1
FTFN FIXTURE
AIRCRAFT
CABLE
INSTALLATION GUIDE FTFN Center Basket LED Tro er
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2022 PacLights All Rights Reserved Page 3 of 3
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL_INST_FTFN_v0
Use Screws to fasten the Angles to the corners of the Channel frame.
Start o by assembling three of the Channels together (Fig. 12).
1
FIG. 12
FIG. 13
Fasten the three Channels to the Ceiling surface. Bolts/Screws not
provided (Fig. 13).
2
FIG. 14
SCREWS
CHANNELS
ANGLE
SURFACE MOUNT
SCREWS
CEILING
Slide in the FTFN fi xture through the open side of the Surface
Mount. This is when all the wiring installations should be made as well.
Refer to the wiring diagram (Fig. 14).
3
SURFACE MOUNT
FTFN FIXTURE
Once the FTFN fi xture is properly installed on the Surface Mount,
fasten the last two Angles and side Channel to completely enclose the
FTFN fi xture (Fig. 15).
4
FIG. 15
SCREWS
ANGLE
CHANNEL
FTFN FIXTURE
After the Surface Mount Kit is properly installed, this is how the FTFN
fi xture should look (Fig. 16).
5
FIG. 16
OPTIONAL FTFN SURFACE MOUNT OPTIONAL FTFN DRYWALL RECESSED FLANGE
Start o by assembling the Recessed Flanges together by fastening
the Screws to the corners of the Recessed Flanges (Fig. 17).
1
FIG. 17
SCREWS
RECESSED
FLANGE
Notch out the ceiling drywall surface. Insert the preassembled Drywall
Flange frame fl ush to the ceiling leaving the fl anged side underneath
the ceiling. If the drywall ceiling is thin install the Cables to support
the frame and the FTFN fi xture. Cables are not included with the
Drywall Flange frame (Fig. 18).
2
FIG. 18 FLANGE SIDE
CABLE
RECESSED
FLANGE
If the drywall Ceiling is at least 1” thick, then the Drywall Flange
frame can be fastened from the sides. See ‘cut-out’ below. Mounting
Screws are not included (Fig. 19).
3
FIG. 19
CEILING
FTFN FIXTURE
SCREW
Carefully mount the FTFN into the Recessed Frame and adjust any
Cables if necessary (Fig. 20.
4
FIG. 20
SURFACE MOUNT
FTFN FIXTURE
SURFACE MOUNT
RECESSED
FLANGE
FTFN FIXTURE
CABLE
RECESSED
FLANGE
/