PacLights BW027 Installation guide

Brand: PacLights

Model: BW027

Type: Installation guide

PacLights BW027 is a versatile LED light bulb that offers a range of features for various lighting needs. It has an optional CCT function, allowing you to select your preferred color temperature from 3000K to 5000K. The BW027 also supports optional occupancy control, enabling you to automate lighting based on motion detection. Additionally, it features optional selectable wattage, letting you adjust the brightness level to suit your requirements.

INSTALLATION GUIDE BW Series Generation 2 LED Light Bulbs

Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com

PL-INST-BW/2-v0

BW/2 INITIAL SET-UP

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

PacLights ﬁ xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR

WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNINGS:

• Make certain power is OFF before installing or maintaining ﬁ xture. No user serviceable parts inside.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.

CAUTION:

• For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened ﬁ rmly. Apply weatherproof silicone

sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and

unused conduit entries.

FIG. 1 FIG. 2

BW/2-012/018/027 BW/2-036/045/054/063 BW/2-080/100/120

Remove the Compact Flourescent Light or Metal Halide bulb CCW (Fig. 1). For the CFL bulb, it is a direct replacement. For the Metal Halide bulb, it

requires the bypass of the Ballast, Capacitor, and Ignitor from the circuit. Refer to Wiring Diagram. If provided, use the Security Cable to ﬁ x onto the BW/2

bulb Tab and at the other end, ﬁ x the Hook onto the Shell (Fig. 2).

Please make sure to bypass the Ballast (along with the Ignitor and Capacitor) before installing the BW/2 LED bulb!

WIRING DIAGRAM

CARABINER

& CABLE

BW/2 BULB

BULB

TAB

NCFL

NBW/2

VVVVVV

BW/2

SOCKET

HOOK

SHELL

BALLAST

CAPACITOR

IGNITOR

VVVVV

BYPASS BALLAST

BYPASS

CAPACITOR

BYPASS

IGNITOR

INSTALLATION GUIDE BW Series Generation 2 LED Light Bulbs

Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com

PL-INST-BW/2-v0

The Optional Occupancy Control is available for select models

(80W/100W/120W) of the BW/2 Series. The Auxiliary (AUX) Port is

underneath the Plug Cover. Unscrew the Plug Cover (Refer to Fig. 3).

If needed, use a ﬂ athead screwdriver. The AUX Port is at the center of

the top of the BW/2 bulb next to the Switches (Fig. 6).

OPTIONAL FIELD-SELECTABLE CCT (Correlated

Color Temperature)

The Optional 3CCT Function is available for select models of the BW/2

Series. Use the Switch underneath the Plug Cover. Unscrew the Plug

Cover (Fig. 3). If needed, use a ﬂ athead screwdriver. The CCT Switch

allows the user to choose a desired color temperature 3000K, 4000K,

5000K (Fig. 4). After selecting the Color Temperature the BW/2 bulb is

ready to install.

FIG. 3

WATTAGE

SWITCH

FIG. 5

CCT SWITCH

OPTIONAL OCCUPANCY CONTROL

FIG. 6

AUX PORT

MICROWAVE

MOTION

CONTROL

FIG. 7

Sensor Segemented Dimming is available when using either Optional

Sensor. Prior to installing the PIR (Passive Infrared) or Microwave

Motion Sensor, move the Wattage Switch to the ﬁ xture’s highest

wattage (Refer to Fig. 5). Install the Microwave Motion Sensor or the

PIR by screwing into the AUX Port and tighten carefully (Fig. 7).

PLUG

COVER

The Optional Selectable Wattage is available for select models (27W

-120W) of the BW/2 Series. Use the Switch underneath the Plug Cover.

Unscrew the Plug Cover (Refer to Fig. 3). If needed, use a ﬂ athead

screwdriver. Each of the select models have their own wattage range from

low-medium-high where the user can make a selection.

OPTIONAL SELECTABLE WATTAGE

FIG. 4

PIR

BW/2 BULB

AUX PORT

PacLights BW027 Installation guide

PacLights BW027 Installation guide

PacLights BW027 Installation guide

Related papers

Other documents