2. Midmark
  3. Integra™ Operatory Cabinetry - Side Cabinetry
Integra™ Operatory Cabinetry - Side Cabinetry

Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What special tools are required for the installation?
    What are the cabinet dimensions for floor mount service?
    How do you adjust the leveling screws?
    How do you adjust the depth of the door?
    How do you connect additional units and install the countertop?
    How do you install the sink and make the plumbing connections?
1
003-1898-00 Rev.A
OSC031S-L (31” Square Sink Unit w/ or w/o Tapmaster™, LH)
OSC031S-R (31" Square Sink Unit w/ or w/o Tapmaster™, RH)
31” Square Sink Unit Installation
Applies to Models:
OSC031S-L, OSC031S-R
Special Tools:
Level
1/4" deep well socket
Caulking Gun
Belt Sander
OSC031S-L (Shown)
DA2179i
NextNext
2
Wall
17-29/32"
(45.48 cm)
DA2224i
WALL
FLOOR MOUNT SERVICE
HOT
COLD
3/4 in (1.9 cm) Hole
1/2 in NPT Water Pipe
Stub out 1 in (2.5 cm) Min.
2-1/2 in (6.4 cm) Max from
finished floor surface.
Use 1/2 in male NPT fitting
on end of stubs for connections
to shut-off valves. Install 1/2 in
inlet x 3/8 in O.D. outlet angle
shut-off valves.
Waste drain 2 in (5.1 cm) hole
1.5 in (3.8 cm) drain pipe
3 in
7.6 cm
4 in
10.2 cm
16"
(40.64 cm)
Floor
Waste drain
2 in (5.1 cm)
hole
1-1/2 in drain
pipe
HOT
COLD
FLOOR
3/4 in (1.9 cm) Hole
1/2 in NPT Water Pipe
Stub out 1-3/4 in (4.5 cm) Min.
3-3/4 in. (9.5 cm) Max from
finished wall surface .
Use 1/2 in male NPT fittings on end of
stubs for connections to shut-off valves.
Install 1/2 in inlet x 3/8 in O.D. outlet
angle shut-off valves.
WALL MOUNT SERVICE
16-1/4 in (41.3 cm)
3 in
7.6 cm
13-1/4 in (33.7 cm)
CABINET DIMENSIONS
Note
All plumbing must be made by a licensed
plumbing contractor and conform to local, city,
and national codes pertaining to the installation.
NextNext
BackBack
3
DA2181i
Sink Cabinet
WALL
DESIRED POSITION OF EDGE OF UNIT
RAISE
CABINET
LOWER
CABINET
1 1/2" (max.)
(3.8 cm)
Equipment Alert
Do not adjust leveling screws more then
1 1/2” (3.8 cm) to prevent lose of stability.
SINK BASE CABINET INSTALLATION
Step 1: Remove bottom
panel from cabinet.
Step 2: Adjust leveling screws
to fully lowered position
and move cabinet to
desired position.
Step 3: Level cabinet with
leveling screws.
NextNext
BackBack
4
DA2183i
DOOR ADJUSTMENT
Vertical Adjustment
A) Loosen both screws.
B) Move up or down.
C) Retighten screws.
Horizontal Adjustment
A) Turn cam screw to move
panel side to side.
Depth Adjustment
A) Turn cam screw to move
panel front to back.
NextNext
BackBack
5
DA2184i
CONNECTING ADDITIONAL UNITS
& COUNTER TOP INSTALLATION
Note
If necessary, sand
counter top to form
to wall.
Step 1: If necessary, level and
connect any additional
storage units.
Step 2: Position counter top so it
extends 3/8” (0.95 cm) to
1/2” (1.3 cm) over each
end of cabinet(s) and secure
with #10 x 5/8” screws.
Special hex bolts
(#10-24 x 3/4”)
NextNext
BackBack
6
DA2185i
SINK INSTALLATION &
PLUMBING CONNECTIONS
LAMINATE TOP SHOWN
Step 1: Caulk around perimeter of
hole, then position sink.
Step 5: Refer to the instructions with
Tapmaster™ faucet controller
for installation procedure.
Step 4: Install faucet and soap
dispenser using instructions
included with those items.
Note
All plumbing must be made by a licensed
plumbing contractor and conform to local,
city, and national codes pertaining to the
installation.
Equipment Alert
When installing a sink, Midmark
recommends securing cabinet to wall.
Failure to comply may result in damage
to plumbing connections.
Step 3: If required, caulk around
perimeter of hole and
install waste ring.
Step 2: Secure sink with bracket kits
included with sink.
NextNext
BackBack
7
BackBack
Midmark Corporation
For contact information, go to:
www.midmark.com
/