2. Focal Point
  3. ID+ 3.5" Pure Cylinder Wall Wash FLCY3WN

Focal Point ID+ 3.5" Pure Cylinder Wall Wash FLCY3WN Installation guide

  • Hello! I've reviewed the instructions for the Focal Point FLCY3N-RD-4H and FLCY3N-RD-7H cylinder lights. This document provides information on proper installation procedures, including electrical connections, aiming, and maintenance. I'm ready to answer your questions about these stem mount luminaires.
  • What type of electrical connection is required?
    What is the mounting requirement for this product?
    What should I do before beginning the installation?
©2023 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference
1 of 4
IS0830 REV. A
ID+ 3.5" Pure Cylinder - Stem Mount
FLCY3N-RD-4H | FLCY3N-RD-7H- Mini Power Canopy
• Luminaires must be installed by a qualified
electrician (check with local and national
codes for proper installation).
• To prevent electrical shock, disconnect
electrical supply before installation or
servicing.
• Contractor is responsible for adequately
reinforcing walls and/or ceilings to support
fixture weight.
• Focal Point, LLC accepts no responsibility
for inadequately reinforced walls and/or
ceilings.
• The information contained in this drawing
is the sole property of Focal Point, LLC. Any
reproduction in part or whole without the
written permission of Focal Point, LLC is
prohibited.
POWER OFF
POWER ON
ATTENTION
SEE ADDITIONAL
INSTRUCTIONS
BEFORE YOU BEGIN COMPONENT KEY
INSTRUCTION KEY
3.55"
90.2mm
1.56"
39.6mm
3.50"
88.9mm
4.00"
101.6mm
" OCTAGONAL JBOX REQUIRED EMERGENCY
PRIOR TO LUMINAIRE INSTALLATION,
SEE PAGE  FOR EMERGENCY
INSTALLATION INSTRUCTIONS.
J-BOX BY OTHERS
Shipped Assembled
STEM MOUNT MINI POWER CANOPY
7" HOUSING
HEIGHT
4" HOUSING
HEIGHT
MINI POWER
CANOPY
STEM
MOUNTING
BRACKET
J-BOX MOUNTING
BRACKET /
DRIVER CARRIAGE
FACE PLATE
FINISHING
RING
2 of 4
IS0830 REV. A ©2023 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference
21
CANOPY ASSEMBLY SHIPS ASSEMBLED
3
HARDWARE
BY OTHERS
MAKE ELECTRICAL CONNECTION
6
457
MAKE ELECTRICAL CONNECTION
8
INSTALL CANOPY
ASSEMBLY PARTS
SIMULTANEOUSLY
8
FACE PLATE HELD IN PLACE MAGNETICALLY
DRIVER SERVICE
TURN OFF POWER SOURCE
PRIOR TO DRIVER SERVICE
18
3 of 4
IS0830 REV. A ©2023 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference
3
WALL WASH AIMING
2
1
LOOSEN LOCKING SCREWS
(DO NOT REMOVE) ROTATE CYLINDER TO DESIRED POSITION TIGHTEN LOCKING SCREWS
(DO NOT OVER TIGHTEN)
X X
OPTIC SERVICE
1 32
45
6
X
DEPRESS TABS TO RELEASE OPTIC
7
USE ALIGNMENT GUIDES ON OPTIC ASSEMBLY
AND LED MODULE FOR PROPER INSTALLATION
4 of 4
IS0830 REV. A ©2023 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference
3 4
EMERGENCY
1
SECURE TO STRUCTURE ABOVE
2
MAKE ELECTRICAL CONNECTION
SEE BATTERY MANUFACTURER
INSTRUCTIONS
EMERGENCY MAXIMUM MOUNTING HEIGHT:
CD & WH REFLECTORS  .'
WD & BK REFLECTORS  .'
HARDWARE
BY OTHERS
PROCEED TO
LUMINAIRE INSTALLATION
8b 98
ALIGN NOTCH ON REFLECTOR WITH
ALIGNMENT GUIDE ON LED MODULE/OPTIC
WALL WASH REFLECTOR ONLY
10
HAND TIGHTEN
ONLY
DO NOT OVER
TIGHTEN
11
/