Focal Point ID+ 4.5" x 4.5" Adjustable Accent FLCS44 / LCS44 Installation guide

Brand: Focal Point

Model: ID+ 4.5" x 4.5" Adjustable Accent FLCS44 / LCS44

Type: Installation guide

1 of 5

IS0783 REV. A

ID+ 4.5" x 4.5" Adjustable

Square Overlap — FLCS44 | LCS44

• Luminaires must be installed by a qualified

electrician (check with local and national

codes for proper installation).

• To prevent electrical shock, disconnect

electrical supply before installation or

servicing.

• Contractor is responsible for adequately

reinforcing walls and/or ceilings to support

fixture weight.

• Focal Point, LLC accepts no responsibility

for inadequately reinforced walls and/or

ceilings.

• The information contained in this drawing

is the sole property of Focal Point, LLC. Any

reproduction in part or whole without the

written permission of Focal Point, LLC is

prohibited.

POWER OFF

POWER ON

LEVEL

ATTENTION

SEE ADDITIONAL

INSTRUCTIONS

BEFORE YOU BEGIN COMPONENT KEY

INSTRUCTION KEY

T-Housing

IC Rated Housing

Emergency - Remote Test Switch

Chicago Plenum Housing

Beamspread optic,

shipped installed

(replacement kits availalbe)

TRIM

OPTIONAL BAR HANGERS  SOLD SEPARATELY

Solite Lens Spot Optic,

no lens

0˚-15˚ tilt

Spot Optic,

no lens

15˚-30˚ tilt

Spot Optic,

no lens

25˚-40˚ tilt

FOCAL POINT

FLCS4-BH-KIT

2 of 5

5 1/4”5 1/4”

GRID  /" CONDUIT & CLIP BY OTHERS

GRID  BAR HANGERS SOLD SEPARATELY

DRYWALL  BAR HANGERS SOLD SEPARATELY

METAL STUDSWOOD STUDS

LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL CEILING.

ALL GRID LUMINAIRES MUST BE SECURED TO STRUCTURE ABOVE.

1 3

3x4

2MULTIPLE LUMINAIRES ONLY

44a

3 of 5

EMERGENCY  REMOTE TEST SWITCH

ABOVE CEILING ACCESS REQUIRED

5.25"

.75"

7.80" ±.25"

5.18"

10.43" ±.25"

511

TIGHTEN SCREW TO SECURE

BAR HANGER IN PLACE

RELEASE TEST SWITCH FROM

BRACKET PRIOR TO INSTALLATION

ADJUST TEST SWITCH UNTIL

CANOPY IS FLUSH WITH CEILING BATTERY UNIT CONNECTOR INSIDE

3/16" max

above ceiling

MAKE ELECTRICAL CONNECTION

SEE

BATTERY MANUFACTURER

INSTRUCTIONS

Emergency maximum

mounting height: 19'

4 of 5

✘

ROTATE MAXIMUM ROTATION: 

TILT MAXIMUM TILT: 

OPTIC SERVICE

TRIM INSTALLATION

10a

9B 9C

ADJUST ANGLE TO ZERO TILT

OPTIC ENGAGES WITH

TWIST & LOCK MECHANISM

REVERSE STEPS TO

INSTALL BEAMSPREAD OPTIC

ENSURE LED MODULE & TRIM

DO NOT INTERFERE

BEFORE INSTALLING

✔

SP & SP: TRIM IS DIRECTIONAL,

ENSURE PROPER ORIENTATION

PUSH BACK ON HEATSINK

NOTCH TO TILT. PUSHING UP

MAY CAUSE BINDING.

PULL FORWARD ON HEATSINK NOTCH

TO REDUCE/ADJUST TILT.

PULLING DOWN MAY CAUSE BINDING.

5 of 5

DRIVER SERVICE

2 3

TILT & ROTATE LED MODULE

AWAY FROM DRIVER.

SEE INSTALLATION STEPS 8 & 9

FOR INSTRUCTIONS.

SPOT OPTIC TILT KIT SOLD SEPARATELY

SP30 & SP40 SHIP WITH

SHROUDS INSTALLED.

SPOT OPTICS KITS ARE AVAILABLE

AS REPLACEMENTS OR IF TILT

ANGLE CHANGES FROM

WHAT WAS SPECIFIED.

Distribtuion: Spot (SP)

Optic Description Tilt Range

SL* Solite Lens 0˚– 40˚

SP00* Spot Optic, No Lens 0˚– 15˚

SP30 Spot Optic, No Lens 15˚– 30˚

SP40 Spot Optic, No Lens 25˚– 40˚

*Shroud not required

SP: 15˚– 30˚

SP: 25˚– 40˚

10b

THE  SETS OF

TRIM MOUNTING

LOCATIONS ARE OFFSET

TO ENSURE TIGHT

TRIMTOCEILING FITMENT.

ROTATE TRIM  AND RE

INSTALL FOR BETTER FIT.

OPTIONAL

Focal Point ID+ 4.5" x 4.5" Adjustable Accent FLCS44 / LCS44 Installation guide

Focal Point ID+ 4.5" x 4.5" Adjustable Accent FLCS44 / LCS44 Installation guide

Focal Point ID+ 4.5" x 4.5" Adjustable Accent FLCS44 / LCS44 Installation guide

Related papers

Other documents