BARRON EHB Series High-Performance LED Linear Highbay Installation guide

Brand
BARRON
Model
EHB Series High-Performance LED Linear Highbay
Type
Installation guide
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
When using electrical equipment, basic safety precautions should always be followed including the following:
• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.
• Installation and servicing of this equipment should be performed by qualified service personnel only.
• Ensure that the electrical wiring conforms to the National Electrical Code NEC® and local regulations
if applicable.
• Do not mount near gas or electrical heaters.
• Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering
by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• Any modification or use of non-original components will void the warranty and product liability.
• Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS!
Technical Support ■ (623) 580-8943 ■ [email protected]
EHB
Installation Instructions
20070139 REV 2 - 08/19 1 800-533-3948 www.barronltg.com
EHB
Installation Instructions
20070139 REV 2 - 08/19 2 800-533-3948 www.barronltg.com
Cable Mount
1. Remove cover plate screw, disengage and remove cover plate, then
remove connection wiring. (Fig. 1)
2. Insert each toggle end of one cable assembly into the elongated holes
located at the end of the fixture. Repeat toggle end insertion with the
second cable assembly on the other end of the fixture. (Fig. 2)
3. Make sure toggles are fully engaged and secure before hanging fixture.
4. Attach the cable loops at the top ends of the cable assemblies onto
suitable anchors or hooks (supplied by others) (Fig. 2).
5. Attach flexible conduit to fixture and route wires using available knockout
locations.
6. Removal of wireway cover screw and wireway for access is optional.
Re-install when installation is complete (Fig 2).
7. Make wire connections per Wiring Diagram and all applicable codes.
8. Re-install cover plate and cover plate screw.
9. Adjust height and level of fixture with cable adjusters by depressing
plunger pin and adjusting cable length.
11. Verify security of installation.
12. Cable mount installation complete.
Fig. 2
Wire Compartment
Cover
Toggle Slots
Y-Toggle
Adjustable
Gripper
Cable
Loop
Adjustable
Cable (5’)
Toggle
Fig. 1
Cover plate &
Cover Plate Screw
Gripper
Plunger Pin
Plunger Pin
Plunger Pin
Adjustable
Cable
Gripper
Plunger Pin
Adjustable
Cable
Wire way
cover
EHB
Installation Instructions
20070139 REV 2 - 08/19 3 800-533-3948 www.barronltg.com
Pendant Mount
1. Remove cover plate screw, disengage and remove cover plate (Fig. 1).
2. Remove connection wiring from within fixture.
3. Locate pendant adapter. Locate four small tabs on inside bottom.
4. Locate 4 slots on fixture housing.
5. Pass fixture wiring through the pendant adapter. Snap the pendant adapter
onto the fixture housing by engaging four pendant adapter tabs into four slots
on sides of the fixture housing.
6. Secure the pendant adapter to fixture housing with (4) screws provided.
Use thread locking liquid.
7. Insert the pendant bracket into the J-Box, engaging tabs into slots and secure
with 2 wing screws (Fig. 5).
8. Partially thread two J-Box mounting screws into the pendant adapter/fixture
assembly (Fig. 4).
9. Hook the tabs of J-Box into two slots in pendant adapter/fixture assembly
(Fig. 6).
10. Make electrical connections per Wiring Diagram and all applicable codes.
11. Align elongated screw slots of J-Box over the pendant adapter/fixture
assembly screws and engage (Fig. 7 & 8).
12. Shift pendant adapter/fixture assembly to fully engage screws in J-Box slots.
Tighten securely using thread locking liquid (Fig. 8).
13. Discard cover plate and cover plate screw.
14. Pendant mount installation complete.
J-Box
Mounting
Screws
Fig. 4
J-Box
slots
Wing
screws
Threaded
holes
Pendant
bracket
Fig. 5
Fixture Housing
Pendant Adapter
Fig. 3
Fig. 6
J-Box
tabs
Pendant Adapter
Slots
Fig. 7 Fig. 8
J-Box
EHB
Installation Instructions
20070139 REV 2 - 08/19 4 800-533-3948 www.barronltg.com
Wiring Diagram
Check fixture label for correct voltage capability.
Make electrical connections as follows:
If present,
Black with White stripe - Unswitched Power
Black - Switched Line
White - Neutral
Green/Yellow Green - Ground
If Dimming is present:
Purple - DIM+
Gray - DIM-
Battery back-up equipped fixture:
Refer to battery backup instruction for operation.
Motion Sensor equipped fixture:
Refer to motion sensor instructions for operation.
Troubleshooting
If the fixture does not operate correctly:
1. Check incoming voltage to the LED driver(s), voltage must be per fixture label.
2. If all LEDs do not illuminate, the driver(s) may be disconnected. Ensure driver(s) are secure. If secure,
us multimeter to check voltages at the output. If low or no voltage, consult the factory.
3. If some, but not all LEDs are illuminated, consult the factory for additional technical support.
4. Battery back-up equipped fixtures: Check that the battery and test button are securely connected. Check the
battery using a multimeter. If the voltage is below the rating written on the battery, replace the battery.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

BARRON EHB Series High-Performance LED Linear Highbay Installation guide

Brand
BARRON
Model
EHB Series High-Performance LED Linear Highbay
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents