Ever POWERLINE 60-33 Operating instructions

Brand: Ever

Model: POWERLINE 60-33

Type: Operating instructions

Instruction manual for the bypass system of the POWERLINE 33 60-140 kVA UPS units

2016-01-18 05:42 Technical support, tel.: +48 61 6500 400 www.ever.eu

TABLE OF CONTENTS

TABLE OF CONTENTS ...................................................................................................................................... 2

SAFETY REMARKS ........................................................................................................................................... 3

OPERATING THE EXTERNAL BYPASS SYSTEM ...................................................................................... 3

SWITCHING FROM THE UPS POWER TO THE MAINS POWER LINE .................................................... 5

SWITCHING FROM THE MAINS POWER LINE TO THE UPS POWER .................................................... 6

TECHNICAL FEATURES .................................................................................................................................. 7

TECHNICAL SPECIFICATIONS ..................................................................................................................... 7

NOTES ................................................................................................................................................................... 7

Instruction manual for the bypass system of the POWERLINE 33 60-140 kVA UPS units

3 www.ever.eu Technical support, tel.: +48 61 6500 400 2016-01-18 05:42

SAFETY REMARKS

Read and understand the safety remarks and guidelines in the (full) Instruction

Manual of this UPS before attempting any switching operations.

CAUTION! Only trained personnel may switch power to the external

bypass system. Switching operations carried out against this procedure

may result in damage to the UPS.

CAUTION! Read and understand the Instruction Manual for this UPS

before attempting the switching operation.

OPERATING THE EXTERNAL BYPASS SYSTEM

Figure 1. Installation diagram of the POWERLINE 33 60-140 kVA UPS.

Instruction manual for the bypass system of the POWERLINE 33 60-140 kVA UPS units

2016-01-18 05:42 Technical support, tel.: +48 61 6500 400 www.ever.eu

Installation diagram symbols:

Fm, Fb, Fsb – Switch fuses (the switch fuse Fb is an optional accessory);

Fspd1, Fspd2 – Breakers,

SPD1, SPD2 – Surge protectors,

Qout, Qsb – Switch disconnectors;

PP1, PP2, PP3 – Emergency power-off (EPO) push-buttons;

A, B, C – Connection wires.

Install the switch fuse Fb, breaker Fspd1 and surge protector SPD1 only if the

optional input BYPASS security. The list of safeguards with the wire sizes for the

UPS models is shown in a separate documentation, "Installation guidelines for the

POWERLINE 33 60-140kVA UPS units".

 This UPS has been designed for operation in TN systems

 Qsb – Mechanically locked in the break position when

receivers are powered from the UPS

 Keep the Fsb links outside of the UPS switching room when

powering the receivers from the UPS.

 Fsb, Qsb – Operated by trained personnel only; Incorrect use may

damage the UPS

Instruction manual for the bypass system of the POWERLINE 33 60-140 kVA UPS units

5 www.ever.eu Technical support, tel.: +48 61 6500 400 2016-01-18 05:42

SWITCHING FROM THE UPS POWER TO THE MAINS POWER LINE

Follow this procedure to switch the isolated UPS-powered network to the mains

power with the external bypass system (Fig. 1):

1. Turn off the UPS. To do this, go in the interface to: Menu -> Control -> UPS -> Off

(the UPS will be powered off on the logical level).

2. Wait until the UPS is turned off on the logical level and indicates that the

connected receivers are powered via the internal bypass with the red LED –

STANDBY mode.

3. Turn on the switch disconnector Qsb on the bypass line.

4. Turn on the switch fuse Fsb on the bypass line.

5. Turn off the switch disconnector Qout on the UPS output line.

6. Turn off the switch fuse Fm on the UPS input line (also turn off Fb if the UPS has a

separate BYPASS line option).

Instruction manual for the bypass system of the POWERLINE 33 60-140 kVA UPS units

2016-01-18 05:42 Technical support, tel.: +48 61 6500 400 www.ever.eu

SWITCHING FROM THE MAINS POWER LINE TO THE UPS POWER

Follow this procedure to switch the isolated mains-powered network (Fig. 1) to the

UPS power:

1. Make sure that the UPS has been powered off on the logical level.

2. Turn on the switch fuse Fm on the UPS input line (also turn on Fb if the UPS has

a separate BYPASS line option).

3. Wait until the UPS indicates that the connected receivers are powered via the

internal bypass with the red LED – STANDBY mode.

4. Turn on the switch disconnector Qout on the UPS output line.

5. Turn off the switch fuse Fsb on the bypass line.

6. Turn off the switch disconnector Qsb on the bypass line.

7. Turn on the UPS. To do this, go in the interface to: Menu -> Control -> UPS ->On

(the UPS will be powered on on the logical level) – red LED goes off MAINS

mode.

CAUTION! Once the procedure for restoring the UPS power has been

completed, secure the disconnectors and fuses on the external bypass

line from inadvertent switching on by unauthorised personnel.

Instruction manual for the bypass system of the POWERLINE 33 60-140 kVA UPS units

7 www.ever.eu Technical support, tel.: +48 61 6500 400 2016-01-18 05:42

TECHNICAL FEATURES

TECHNICAL SPECIFICATIONS

PARAMETERS / MODEL

EXTERNAL BYPASS FOR

POWERLINE 33 (60-100kVA)

EXTERNAL BYPASS FOR

POWERLINE 33 (120-140kVA)

Dimensions

(height × width × depth)

1050 x 660 x 270 mm

1250 x 660 x 270 mm

Net weight

48 kg

60 kg

NOTES

Ever POWERLINE 60-33 Operating instructions

Ever POWERLINE 60-33 Operating instructions

Ever POWERLINE 60-33 Operating instructions

Related papers

Other documents