800026-Rev 0
Parts Included:
• Square Corner Cabinet
• Filler - (Shipped on underside of cabinet)
• Blind Panel - (Shipped on underside of cabinet)
Materials Needed
• #6 x ½” Flat Head Screws
• 2 ½” Trim Head or Flat Head Wood Screws
• 2 ½” Round Washer Head Screws
(6.18.13) SCB INSTRUCTIONS A5131
Instructions for Square Corner Cabinet Installation
Parts Included:
(1) Blind Panel
(1) Square Corner Cabinet
(1) Filler Board
Tools Needed:
Phillips Head Screwdriver, Tape Measure,
Marking Tool, Drill with 7/64” Bit and 3/32”
Bit, Saw
Square Corner Cabinet Information:
STEP 1
Parts Needed:
(8) #6 x 1/2” Flat Head Screws
(2) #10 X 2 1/2” Washer Head Screws
(2) # 8 Flat Head Screws of Appropriate length
KEY
X: Minimum pull for
Square Corner Cabinet
Y: Maximum pull for
Square Corner Cabinet
Z: Minimum filler size
required between
cabinets
Min. pull is defined
when square corner or
adjacent cabinet doors
can be opened 90 deg.
and/or drawers can be
fully extended without
hitting adjacent cabinet
door/drawer when shut.
SQUARE CORNER
CABINET
ADJACENT
CABINET
Z
Y
X
Filler Board
Wall
=Open Space
Y
Min. Pull
Min. Pull w/Hardware
Max. Pull
Min. Filler Required Min. Filler Required w/Hardware
1 1/4" Overlay
3/4" 2 1/4" 12 1/2" 1" 2 1/2"
7/16" Overlay
1/4" 1 3/4" 12 1/2" 1/2" 2"
X
Z
NOTE: To determine your cabinet’s over-
lay, measure the distance from the
drawer or door to the edge of the face
frame and reference the drawing above.
Remove baseboard and other objects on the wall
area where the cabinets are to be installed. Using a
straight edge and a level, find the high point in the
floor where the cabinets are to be installed. From the
high point, mark a level horizontal line on each wall
where the cabinets will be attached. From the level
lines mark another parallel level horizontal line 35" up
for base cabinets, 54" for wall cabinets and 84", 90"
or 96", depending upon your tall cabinet heights. The
top of the base and tall cabinets and the bottom of
the wall cabinets will be located at these marks.
ATTN: FILLER BOARD AND COVER PANEL ARE STAPLED
UNDERNEATH YOUR SQUARE CORNER BASE CABINET.
NOTE: To determine your
cabinet’s overlay, reference
left image showing door &
drawer front coverage of
face frame
(6.18.13) SCB INSTRUCTIONS A5131
STEP 2
STEP 3
STEP 4
The blind panel will need to be trimmed to size to fit
over the opening of your square corner base cabinet.
Then the blind panel will need to be drilled for
installation. Mark the (8) hole locations shown to the
right on the blind panel. All holes should be located
1/4" from edges of blind panel. Drill the (8)
premarked locations with a 7/64" diameter drill bit
through the panel.
*Panel is located under cabinet with Filler Board
Locate the studs with a stud finder and mark where
the cabinets are to be installed. Remove all the doors
and drawers from the cabinets before installation.
Measure the area to confirm that the kitchen design
used will work.
Remove door and drawer from square corner
cabinet. On the square corner opening side
of the face frame (opening without door
attached), a line 1/2” from the edge of the
opening needs to be marked onto the face
frame. This will locate the blind panel for
attachment.
NOTE: Door can be placed on either side of
the cabinet depending on design needs.
DOOR LOCATION
FACE FRAME
1/2
1/2
1/2
1/2
Step 1: Inspect and Preparation
Follow Wall and Base Cabinet instructions for cabinet inspection and preparing
and marking the walls for cabinet installation. Install all wall cabinets before
installing the SCB corner cabinet.
Square Corner Cabinet Information:
Full Overlay Partial Overlay
Step 2: Blind Panel Preparation
Locate and remove the blind panel and ller from the underside of the cabinet.
Set ller aside for later use. Trim blind panel so it covers the open side of the blind
corner cabinet by 1/2" on all (4) sides of the opening. Mark (8) hole locations
shown in the image to the right ¼” from the edges of the blind panel. Predrill the
(8) marked locations with a 3/32” diameter drill bit.
Step 3: Blind Panel Installation
On the square corner opening side of the face frame (opening without the door
attached), mark lines onto the face frame ½” from the edge of the door opening.
This will locate the blind panel for attachment. Place predrilled blind panel onto
face frame and mark the pre-drilled hole locations from the blind panel onto the
face frame. Remove blind panel and predrill face frame with a 3/32” diameter
drill bit in all (8) locations, ½” deep. Attach blind panel to face frame using (8)
#6 x ½” at head screws.
Square Corner Cabinet
Installation Instructions
CAUTION: Never use nails to mount cabinets. The use of nails may
void your factory warranty, written or implied.
(6.18.13) SCB INSTRUCTIONS A5131
STEP 2
STEP 3
STEP 4
The blind panel will need to be trimmed to size to fit
over the opening of your square corner base cabinet.
Then the blind panel will need to be drilled for
installation. Mark the (8) hole locations shown to the
right on the blind panel. All holes should be located
1/4" from edges of blind panel. Drill the (8)
premarked locations with a 7/64" diameter drill bit
through the panel.
*Panel is located under cabinet with Filler Board
Locate the studs with a stud finder and mark where
the cabinets are to be installed. Remove all the doors
and drawers from the cabinets before installation.
Measure the area to confirm that the kitchen design
used will work.
Remove door and drawer from square corner
cabinet. On the square corner opening side
of the face frame (opening without door
attached), a line 1/2” from the edge of the
opening needs to be marked onto the face
frame. This will locate the blind panel for
attachment.
NOTE: Door can be placed on either side of
the cabinet depending on design needs.
DOOR LOCATION
FACE FRAME
1/2
1/2
1/2
1/2
(6.18.13) SCB INSTRUCTIONS A5131
STEP 5
STEP 6
STEP 7
Attach the blind panel to the face frame
using the recommended (8) #6 x 1/2" flat
head screws. These screws must be
purchased separately. Reattach the door
and drawer front to the cabinet.
Place the predrilled blind panel onto the
face frame using the markings placed on
the face frame in the last step. Mark the
predrilled hole locations from the blind
panel onto the face frame. Remove the
blind panel and predrill the face frame (8)
places with a 7/64" diameter drill bit, 1/2"
deep.
Position the Square Corner Base cabinet
with reference to the specifications on
page one. Do not secure to the wall yet.
SQUARE CORNER
CABINET
ADJACENT
CABINET
Z
Y
X
Filler Board
Wall
=Open Space
MARK
(8) HOLE
LOCATIONS
ONTO THE
FACE FRAME.
Attach panel to the face frame
using the (8) #6 x 1/2"
flat head screws.
NOTE: Door can be placed on either side of the cabinet depending on design needs.
800026-Rev 0
STEP 4: Begin Square Corner Cabinet Installation
Position the square corner cabinet and the adjacent cabinet in place with
reference to the ller and pull specication table on page 1. Setting the
appropriate amount of pull is critical for a successful installation. Conrm the
square corner cabinet is sitting level and plumb. If needed, add shims to level.
Remove adjacent cabinet to allow room for install.
STEP 5: Complete Square Corner Cabinet Installation
Locate predetermined wall studs and transfer marks to the inside of the cabinet.
Drill through the cabinet back and into the wall stud with a 3/32” diameter drill bit,
approximately 2” deep. The holes should come no closer than 2” to any inside
vertical edge of the cabinet. Insert the 2 ½” round washer head screws into the
holes until they are nearly tight. Check to ensure the cabinet remained level and
plumb. Adjust as needed before fully tightening the screws.
STEP 6: Determine Filler Width
Following your design layout, place the adjacent cabinet next to the square
corner base cabinet that has been installed. The width of the ller, Z, can now be
determined in accordance with the specication table on page 1 and your design
layout. Rip ller to desired width if necessary.
STEP 7: Filler Installation
With the ller at the desired width, clamp ller to the appropriate side of the
adjacent cabinet face frame. Align the ller vertically to the frame and ensure the
face of the ller is ush with the face of the frame. Drill two 3/32” diameter holes
through the face frame and into the ller near the top and bottom. Then, insert and
tighten 2 ½” trim head or at head wood screws to fasten the ller to the adjacent
cabinet frame. (NOTE: If ller width is less than one inch, use shorter screws).
(6.18.13) SCB INSTRUCTIONS A5131
STEP 5
STEP 6
STEP 7
Attach the blind panel to the face frame
using the recommended (8) #6 x 1/2" flat
head screws. These screws must be
purchased separately. Reattach the door
and drawer front to the cabinet.
Place the predrilled blind panel onto the
face frame using the markings placed on
the face frame in the last step. Mark the
predrilled hole locations from the blind
panel onto the face frame. Remove the
blind panel and predrill the face frame (8)
places with a 7/64" diameter drill bit, 1/2"
deep.
Position the Square Corner Base cabinet
with reference to the specifications on
page one. Do not secure to the wall yet.
SQUARE CORNER
CABINET
ADJACENT
CABINET
Z
Y
X
Filler Board
Wall
=Open Space
MARK
(8) HOLE
LOCATIONS
ONTO THE
FACE FRAME.
Attach panel to the face frame
using the (8) #6 x 1/2"
flat head screws.
(6.18.13) SCB INSTRUCTIONS A5131
STEP 8
STEP 9
STEP 10
Measure from the corner to the first wall stud mark.
Transfer this measurement to the inside of the wall corner
cabinet. Mark the placement of the next wall stud. Drill
through the wall cabinet back into the prelocated studs
with a 3/32" diameter drill bit, approximately 2" deep. The
holes should be positioned 3/4" down from the inside top
of the cabinet but should come no closer than 2" to any
inside vertical edge of the cabinet. Cement, block, brick,
or tile walls will require anchors for screws or toggle bolts.
These will need to be purchased separately if needed.
Insert #10 x 2 1/2" screws into the holes until they are
nearly tight. Do not tighten the screws until you have
finished all final leveling and shimming as needed. Check
the front sides and tops of all cabinets with a level. After
the cabinet is level and plumb, tighten the installation
screws.
NOTE: Never use nails to mount cabinets. The use of
nails may void your factory warranty, written or implied.
Once the square corner base cabinet is positioned in step
5, confirm that the cabinet is sitting level and straight.
Remove the adjacent cabinet to allow for room to install
the square corner base cabinet. If needed, add shims to
level the cabinet.
Level
Following your design layout, replace the adjacent cabinet
next to the square corner base cabinet that has been
installed. The width of the filler, Z, can now be determined
in accordance with the specifications on page one and
your design layout.
*Filler Board is located under cabinet with Blind Cover
Panel.
SQUARE CORNER
CABINET
ADJACENT
CABINET
Z
Y
X
Filler Board
Wall
=Open Space
NOTE: Never use nails to mount cabinets. The use of nails may void your factory
warranty, written or implied.
(6.18.13) SCB INSTRUCTIONS A5131
STEP 8
STEP 9
STEP 10
Measure from the corner to the first wall stud mark.
Transfer this measurement to the inside of the wall corner
cabinet. Mark the placement of the next wall stud. Drill
through the wall cabinet back into the prelocated studs
with a 3/32" diameter drill bit, approximately 2" deep. The
holes should be positioned 3/4" down from the inside top
of the cabinet but should come no closer than 2" to any
inside vertical edge of the cabinet. Cement, block, brick,
or tile walls will require anchors for screws or toggle bolts.
These will need to be purchased separately if needed.
Insert #10 x 2 1/2" screws into the holes until they are
nearly tight. Do not tighten the screws until you have
finished all final leveling and shimming as needed. Check
the front sides and tops of all cabinets with a level. After
the cabinet is level and plumb, tighten the installation
screws.
NOTE: Never use nails to mount cabinets. The use of
nails may void your factory warranty, written or implied.
Once the square corner base cabinet is positioned in step
5, confirm that the cabinet is sitting level and straight.
Remove the adjacent cabinet to allow for room to install
the square corner base cabinet. If needed, add shims to
level the cabinet.
Level
Following your design layout, replace the adjacent cabinet
next to the square corner base cabinet that has been
installed. The width of the filler, Z, can now be determined
in accordance with the specifications on page one and
your design layout.
*Filler Board is located under cabinet with Blind Cover
Panel.
SQUARE CORNER
CABINET
ADJACENT
CABINET
Z
Y
X
Filler Board
Wall
=Open Space
800026-Rev 0
STEP 8: Adjacent Cabinet Installation
Position the adjacent cabinet and ller assembly in place. Check the cabinet to
ensure it is both level and plumb using shims if necessary. Make sure the ller is
properly aligned to the square corner cabinet face frame. Follow Step 5 to secure
the adjacent cabinet to the wall.
Step 9: Attach Square Corner to Filler/Adjacent
Cabinet Assembly
After the adjacent cabinet has been secured to the wall, use clamps to securely join
the cabinets together. Ensure the ller and adjacent cabinet assembly is still properly
aligned to the square corner cabinet. Mark two locations on the inside of the square
corner cabinet face frame that coincides with the center of the ller. Drill two 3/32”
diameter holes through the square corner cabinet face frame and into the ller near
the top and bottom. Then, insert and tighten 2 ½” trim head or at head wood
screws to fasten the ller and adjacent cabinet to the square corner cabinet
(6.18.13) SCB INSTRUCTIONS A5131
STEP 11
STEP 12
STEP 13
With the adjacent cabinet removed, the Filler Board
can be clamped to the square corner cabinet in the
position marked in the previous step. Drill two 3/32”
holes into the filler board through the face frame of
the cabinet. Then use 2 #8 cabinet screws of the
appropriate length depending on the width of your
filler board if you cut to fit your design layout. If the
Filler Board’s width was not cut down, use 2” long
#8 cabinet screws.
Once the square corner cabinet has been installed,
the adjacent base cabinets can now be installed.
Start installing the base cabinets in the corner.
Using clamps, align and join the cabinets together
at the face frames. Make sure that the face frames
align both on the face and vertically.
Check the cabinet to ensure it is level and plumb.
Shim to fill uneven areas between the floor and
base of the cabinet and between the wall and the
back of the cabinet. Failure to do this step could
result in damage to the cabinet.
Follow Step 9 to secure adjacent cabinet to the
wall.
With the adjacent cabinet positioned next to the
installed square corner cabinet, mark the location
of the filler board on the inside of the square corner
cabinet face frame.
SQUARE CORNER
CABINET
ADJACENT
CABINET
Filler Board
Wall
=Open Space
Pencil
SQUARE CORNER
CABINET
Filler Board
Wall
Clamp
Shims
(6.18.13) SCB INSTRUCTIONS A5131
STEP 11
STEP 12
STEP 13
With the adjacent cabinet removed, the Filler Board
can be clamped to the square corner cabinet in the
position marked in the previous step. Drill two 3/32”
holes into the filler board through the face frame of
the cabinet. Then use 2 #8 cabinet screws of the
appropriate length depending on the width of your
filler board if you cut to fit your design layout. If the
Filler Board’s width was not cut down, use 2” long
#8 cabinet screws.
Once the square corner cabinet has been installed,
the adjacent base cabinets can now be installed.
Start installing the base cabinets in the corner.
Using clamps, align and join the cabinets together
at the face frames. Make sure that the face frames
align both on the face and vertically.
Check the cabinet to ensure it is level and plumb.
Shim to fill uneven areas between the floor and
base of the cabinet and between the wall and the
back of the cabinet. Failure to do this step could
result in damage to the cabinet.
Follow Step 9 to secure adjacent cabinet to the
wall.
With the adjacent cabinet positioned next to the
installed square corner cabinet, mark the location
of the filler board on the inside of the square corner
cabinet face frame.
SQUARE CORNER
CABINET
ADJACENT
CABINET
Filler Board
Wall
=Open Space
Pencil
SQUARE CORNER
CABINET
Filler Board
Wall
Clamp
Shims
-
1
-
2
-
3
Diamond NOW 36E SCB36R Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Wyndham Collection WCS777716WES Installation guide
-
Wyndham Collection WCS2020WCWG Installation guide
-
Hampton Bay KAFS330-CHR Installation guide
-
L.L.Bean HOME Mission Cabinet Small Quick start guide
-
Hampton Bay CM3012W-WH Operating instructions
-
Design House 531319 Installation guide
-
Midmark Wall Cabinet Installation guide
-
Whirlpool R1012 Installation Instructions And Use & Care Manual
-
-
WeatherStrong WSE120I-DTK Installation guide
