MULTIPLEX Ice Bin Drain Collector Box Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Ice Bin Drain Collector Box
Type
Installation guide

This manual is also suitable for

MULTIPLEX Ice Bin Drain Collector Box

The MULTIPLEX Ice Bin Drain Collector Box is a device designed to help prevent water damage from ice bin drains. It is compatible with Servend Ice/Beverage Dispensers with extended splash panels, excluding MDH series dispensers.

Key Features:

  • Prevents water damage from ice bin drains
  • Easy to install with provided instructions
  • Durable construction for long-lasting use

Possible Use Cases:

  • Commercial kitchens
  • Restaurants
  • Bars
  • Convenience stores
  • Any establishment with Servend Ice/Beverage Dispensers with extended splash panels

MULTIPLEX Ice Bin Drain Collector Box

The MULTIPLEX Ice Bin Drain Collector Box is a device designed to help prevent water damage from ice bin drains. It is compatible with Servend Ice/Beverage Dispensers with extended splash panels, excluding MDH series dispensers.

Key Features:

  • Prevents water damage from ice bin drains
  • Easy to install with provided instructions
  • Durable construction for long-lasting use

Possible Use Cases:

  • Commercial kitchens
  • Restaurants
  • Bars
  • Convenience stores
  • Any establishment with Servend Ice/Beverage Dispensers with extended splash panels
Instructions
Manitowoc Beverage Systems Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
020003915 REV1
3/12
Subject: Extended Splash Panel Collector Box
These steps are for installation of one kit (020003917 or
020003918) on Servend Ice/Beverage Dispensers with extended
splash panel. Not for use with MDH series dispensers.
Tools Required
• Phillips Head Screwdriver
• Standard Screwdriver or 5/16 Nut Driver
INSTALLATION OF KIT
1. Remove power from the unit.
Splash Panel Removal
2. Remove the extended splash panel from the unit by removing the
two (2) phillips head screws holding it in place.
3. If installing kit 020003918 skip to Step
8.
Existing Drain Lines
4. Disconnect the existing insulated ice bin drain lines from the two
(2) 90° rubber drain line elbows. (See Figure 1)
5. Remove the two (2) 90° rubber drain line elbows from the ice bin
drains. (See Figure 2)
Collector Box Assembly
6. Mount the collector box bracket by sliding it under the motor box
edge and placing the holes over ice bin drains. (See Figure 3)
7. Secure the bracket into place by either reinstalling the 90° rubber
elbows or using new ones. (See Figure 3)
NOTE: Be sure that the 90° rubber elbows are straight, not at an angle
and hold the bracket tight against foam front of the unit, the bracket
should not be able to move. (See Figure 3)
!
Warning
Electric Shock & Moving Parts Hazard
Unplug unit before servicing.
KIT 020003917 CONTENTS
QTY DESCTRIPTION
1 Kit Instructions
1 Insulated Drain Kit with Fittings
1 Collector Box Bracket
2 90° Rubber Elbow
1 Insulated Collector Box
KIT 020003918 CONTENTS
QTY DESCTRIPTION
1 Kit Instructions
1 Insulated Drain Kit with Fittings
1 Insulated Collector Box
Important
If the splash panel has ADA key pads they are sealed to the ribbon cables
and connected to the control board, gently lay the splash panel in front of
the unit being careful not to damage the cables.
FIGURE 2 - Remove Rubber Elbows
FIGURE 1 - Remove Existing Drain Lines
FIGURE 3 - Mount the Bracket
Standard SV Dispenser with extended splash panel
Extended
Splash Panel
90° Elbow
Ice Bin Drain
Insulated Ice Bin
Drain line
90° Elbow
Ice Bin Drain
Collector Box Bracket
Motor Box Edge
90°
Elbows
Extended Splash Panel Collector Box 020003915 REV1 3/12
Manitowoc Foodservice Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
8. Screw the drain line fittings into the collector box. (See Figure 4)
NOTE: Depending on the drain setup connect the straight fittings to
the collector box if the drain lines are to run straight back underneath
the unit or the 90° fittings if the drain lines run down through the
counter top. (See Figure 4)
Reinstall the Drain Lines
9. Using the provided radiator clamps connect and secure the drain
lines to the collector box fittings with a standard screwdriver or
5/16 nut driver. (See Figure 5)
10. Mount the collector box to the bracket by sliding the right and left
bracket tabs into the slots on the collector box. (See Figure 6)
NOTE: Be sure the 90° rubber elbows are routed into the collector
box. (See Figure 7)
Finish Installation
11. Put the extended splash panel back onto the unit and reinstall the
two (2) screws that hold it in place.
12. Restore power to the unit.
FIGURE 4 - Drain Line Fittings
FIGURE 5 - Connect Drain Lines
FIGURE 6 - Mount Collector Box
Collector
Box
Straight Fittings 90° Fittings
Drain Line
Fittings
Drain Line
Fitting
Drain Line
Collector
Box
FIGURE 7 - Correctly Mounted Collector Box
Left Bracket
Tab
Right
Bracket Tab
Left Slot
Right Slot
Left Tab In
Slot
Right Tab In
Slot
90° Elbow
90° Elbow
  • Page 1 1
  • Page 2 2

MULTIPLEX Ice Bin Drain Collector Box Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Ice Bin Drain Collector Box
Type
Installation guide
This manual is also suitable for

MULTIPLEX Ice Bin Drain Collector Box

The MULTIPLEX Ice Bin Drain Collector Box is a device designed to help prevent water damage from ice bin drains. It is compatible with Servend Ice/Beverage Dispensers with extended splash panels, excluding MDH series dispensers.

Key Features:

  • Prevents water damage from ice bin drains
  • Easy to install with provided instructions
  • Durable construction for long-lasting use

Possible Use Cases:

  • Commercial kitchens
  • Restaurants
  • Bars
  • Convenience stores
  • Any establishment with Servend Ice/Beverage Dispensers with extended splash panels
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents