Hagerco 5200 Series Standard Slide Track Arms Installation guide

Hagerco
Brand
Hagerco
Model
5200 Series Standard Slide Track Arms
Type
Installation guide

Hagerco 5200 Series Standard Slide Track Arms

The Hagerco 5200 Series Standard Slide Track Arms are designed to provide a smooth and controlled door closing action. They are ideal for use on a variety of door types, including wood, metal, and glass doors. The arms are made from high-quality materials and are built to last.

Some of the features of the Hagerco 5200 Series Standard Slide Track Arms include:

  • Adjustable spring power to accommodate different door sizes and weights
  • Hold-open feature to keep the door open at a desired angle
  • Backcheck feature to prevent the door from slamming open

Hagerco 5200 Series Standard Slide Track Arms

The Hagerco 5200 Series Standard Slide Track Arms are designed to provide a smooth and controlled door closing action. They are ideal for use on a variety of door types, including wood, metal, and glass doors. The arms are made from high-quality materials and are built to last.

Some of the features of the Hagerco 5200 Series Standard Slide Track Arms include:

  • Adjustable spring power to accommodate different door sizes and weights
  • Hold-open feature to keep the door open at a desired angle
  • Backcheck feature to prevent the door from slamming open
ACHIEVED.
PARTS
OF 1/2" UNTIL
DESIRED ANGLE IS
DOOR PREP PULL SIDE APPLICATION (RIGHT HAND SHOWN) 120
IN INCREMENTS
THE PIVOT HINGE
SCREW ORIENTATION SHOWN
DEPENDING ON HANDING; SIDE MOUNT
INSERT/HOLD OPEN STOP MAY FLIP SIDES ORIENTATION SHOWN
SIDE MOUNT SCREW
WITHOUT SLIDE ARM:
ORIENTATION FOR ALL MOUNTS; SLIDE
WITH SLIDE ARM: SAME ASSEMBLY
NOTE: IF USER
WISHES
TO HAVE A LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD OPEN
STOP
OR STOP ONLY
AWAY FROM
Installation Sequence:
Use door prep above to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.1.
Fasten closer body to door with power adjustment port away from hinge.2.
Position slide track to frame face orientated with countersink visible open side facing down and with hold 3.
open stop end toward hinge edge of door. Slide end caps on, insert screw through end caps
and fasten to the frame.
Place slide arm on pinion shaft of closer so arm is positioned at a 45 degree angle out from door face.4.
Secure arm with arm washer and arm screw.5.
To properly preload closer, push arm towards door and secure other end of slide arm to track by screwing 6.
it to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against
slide insert and tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.7.
REV: 4 REV DATE: 09/09/2020
I-CL00578 Rev 4
5200 Track Arm
Installation Instructions
Page 1 of 4
Slide Insert
Stop Only
[504.8]
25.8
TOP OF
DOOR
OF HINGE
19 7/8"
CENTERLINE
132.7
OF HINGE
CENTERLINE
127.1
5"
5 7/32"
12"
304.8
3/4"
19
1"
1 3/16"
30.1
TOP OF
DOOR
UNIVERSAL
HOLD OPEN STOP
END CAP
SLIDE INSERT
MOUNTING
SCREW
Hold Open Stop
SET SCREW
SCREW
SLIDE TRACK
SLIDE ARM
SLIDE ARM
INSERT
UNIVERSAL END CAP
Installation Sequence:
Use door prep above to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.1.
Fasten closer body to door with power adjustment port towards hinge.2.
Position slide track to frame face orientated with countersink visible open side facing down and with hold 3.
open stop end toward hinge edge of door. Slide end caps on, insert screw through end caps
and fasten to the frame.
Place slide arm on pinion shaft of closer so arm is positioned at a 45 degree angle out from door face.4.
Secure arm with arm washer and arm screw.5.
To properly preload closer, push arm towards door and secure other end of slide arm to track by screwing it 6.
to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against slide
insert and tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.7.
TOP JAMB (PULL SIDE) MOUNTING APPLICATION (RIGHT HAND SHOWN) 120 DOOR PREP
NOTE: IF USER
WISHES
TO HAVE A LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD OPEN
STOP
OR STOP ONLY
AWAY FROM
THE PIVOT HINGE IN
INCREMENTS
OF 1/2" UNTIL
DESIRED ANGLE IS
ACHIEVED.
5200 Track Arm
Installation Instructions
I-CL00578 Rev 4
REV: 4 REV DATE: 09/09/2020 Page 2 of 4
[504.8]
CENTERLINE OF THESE HOLES VERTICALLY IN LINE WITH CENTERLINE OF HINGE
NOTE: REQUIRES 5918 DROP PLATE WHERE
THE HEAD FRAME FACE IS LESS THAN 3"
REFERENCE PAGE 3 FOR CUSTOM MOUNTING
12"
304.8
3/4"
19
3/8"
9.5
TOP OF
DOOR
1 3/4"
44.5
TOP OF
DOOR
3 1/8"
79.4
CENTERLINE
OF HINGE
FRAME FACE 3" OR GREATER
19 7/8"
TOP JAMB (PULL SIDE) MOUNT (RIGHT HAND SHOWN) 120 CUSTOM DOOR PREP WITH 5918 PLATE
Installation Sequence:
Use template above to locate mounting holes on pocket wall and mount closer according to pull side 1.
application template. Drill 1/8" pilot holes for the self tapping screws.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.2.
Fasten closer body to door with power adjustment port away from hinge.3.
Fasten slide track to pocket wall face with open side facing down and with hold open stop end away from 4.
hinge edge of door. Slide end caps on, orientated with countersink visible. Screw will go through end caps
as it fastens to the frame.
Connect slide arm to track by screwing it to the slide insert. DOOR MUST REMAIN IN CLOSED POSITION 5.
FOR FOLLOWING ASSEMBLY STEPS.
Swing arm toward closer and rest the hub of the arm on top of the closer pinion. Place a wrench on the 6.
bottom pinion of the closer and rotate away from the hinge (approx. 30 degrees). When the cutout of the
arm hub and the pinion line up, slide the arm hub down over the pinion and secure tightly with the
washer and screw. This pretensions the closer arm.
Loosen the stop only/hold open stop and open door to required opening angle. Close the door. Now slide 7.
the stop only/hold open stop back towards the hinge about 1/2" and tighten down the stop only/hold
open stop via set screw.
Pocket Pivots 6-1/2"
4-1/2" x 4-1/2" Hinges,
Swing Clear Hinges,
or 3/4" Offset Pivots
5"
Dim "B"Pivot/Hinge Type
POCKET DOOR APPLICATION 90 OPEN DOOR INTO POCKET
NOTE: IF USER
WISHES
TO HAVE A LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD OPEN
STOP
OR STOP ONLY
AWAY FROM
THE PIVOT HINGE
IN INCREMENTS
OF 1/2" UNTIL
DESIRED ANGLE IS
ACHIEVED.
Installation Sequence:
Use door prep above to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.1.
Fasten closer body to 5918 plate with power adjustment port towards hinge.2.
Position slide track to frame face orientated with countersink visible open side facing down and with hold 3.
open stop end toward hinge edge of door. Slide end caps on, insert screw through end caps
and fasten to the frame.
Place slide arm on pinion shaft of closer so arm is positioned at a 45 degree angle out from door face.4.
Secure arm with arm washer and arm screw.5.
To properly preload closer, push arm towards door and secure other end of slide arm to track by screwing it 6.
to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against slide
insert and tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.7.
5200 Track Arm
Installation Instructions
I-CL00578 Rev 4
REV: 4 REV DATE: 09/09/2020 Page 3 of 4
[504.8]
HOLES TO MOUNT CLOSER (CLOSER NOT SHOWN FOR CLARITY)
CENTER OF THIS HOLE VERTICALLY IN LINE WITH CENTERLINE OF HINGE
5918
NOTE: REQUIRES 5918 DROP PLATE WHERE
THE HEAD FRAME FACE IS LESS THAN 3"
4"
101.6
4"
101.6
4"
101.6
9/32"
7.4
3/8"
9.5
TOP OF
DOOR
1 3/8"
34.9
TOP OF
DOOR
3 1/8"
79.4
CENTERLINE
OF HINGE
19 7/8"
LESS THAN 3" FRAME FACE
Mount track 1-1/16"
above top of door to
center of screw holes on
track
B
21 11/32"
541.7
POCKET DEPTH 2-1/2"-5"
5200 DOOR CLOSER ADJUSTMENTS
5200 Track Arm
Installation Instructions
I-CL00578 Rev 4
REV: 4 REV DATE: 09/09/2020 Page 4 of 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Hagerco 5200 Series Standard Slide Track Arms Installation guide

Hagerco
Brand
Hagerco
Model
5200 Series Standard Slide Track Arms
Type
Installation guide

Hagerco 5200 Series Standard Slide Track Arms

The Hagerco 5200 Series Standard Slide Track Arms are designed to provide a smooth and controlled door closing action. They are ideal for use on a variety of door types, including wood, metal, and glass doors. The arms are made from high-quality materials and are built to last.

Some of the features of the Hagerco 5200 Series Standard Slide Track Arms include:

  • Adjustable spring power to accommodate different door sizes and weights
  • Hold-open feature to keep the door open at a desired angle
  • Backcheck feature to prevent the door from slamming open
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents