Hagerco 5200 Series Standard Slide Track Arms Installation guide

Hagerco
Brand
Hagerco
Model
5200 Series Standard Slide Track Arms
Type
Installation guide

Hagerco 5200 Series Standard Slide Track Arms are designed to provide reliable door control solutions for a variety of applications. With a hold-open feature and adjustable spring power, these arms ensure smooth and controlled door movement. They are suitable for both pull-side and top jamb mounting, offering versatility in installation. The arms' sturdy construction and easy adjustment make them ideal for commercial and residential use, ensuring optimal door operation and enhancing the overall functionality of your space.

Hagerco 5200 Series Standard Slide Track Arms are designed to provide reliable door control solutions for a variety of applications. With a hold-open feature and adjustable spring power, these arms ensure smooth and controlled door movement. They are suitable for both pull-side and top jamb mounting, offering versatility in installation. The arms' sturdy construction and easy adjustment make them ideal for commercial and residential use, ensuring optimal door operation and enhancing the overall functionality of your space.

UNIVERSAL
END CAP
SLIDE INSERT
HOLD OPEN STOP
MOUNTING
SCREW
Hold Open Stop
SET SCREW
Stop Only
Slide Insert
5 7/32"
132.7
19 7/8"
504.8
5"
127.1
12"
304.8
3/4"
19
1"
25.8
1 3/16"
30.1
TOP OF DOOR
TOP OF
DOOR
SLIDE TRACK
SLIDE ARM
SLIDE ARM
INSERT
SCREW
UNIVERSAL END CAP
PARTS
PULL SIDE APPLICATION (RIGHT HAND SHOWN) 120
DOOR PREP
WITH SLIDE ARM: SAME ASSEMBLY
ORIENTATION FOR ALL MOUNTS; SLIDE
INSERT/HOLD OPEN STOP MAY FLIP SIDES
DEPENDING ON HANDING; SIDE MOUNT
SCREW ORIENTATION SHOWN
WITHOUT SLIDE ARM:
SIDE MOUNT SCREW
ORIENTATION SHOWN
NOTE: IF USER
WISHES
TO HAVE A
LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD
OPEN STOP
OR STOP ONLY
AWAY FROM
THE PIVOT
HINGE IN
INCREMENTS
OF 1/2" UNTIL
DESIRED ANGLE
IS ACHIEVED.
Installation Sequence:
Use door prep above to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.
1.
Fasten closer body to door with power adjustment port away from hinge.
2.
Position slide track to frame face orientated with countersink visible open side facing down and with hold
3.
open stop end toward hinge edge of door. Slide end caps on, insert screw through end caps
and fasten to the frame.
Place slide arm on pinion shaft of closer so arm is positioned at a 45 degree angle out from door face.
4.
Secure arm with arm washer and arm screw.
5.
To properly preload closer, push arm towards door and secure other end of slide arm to track by screwing
6.
it to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against
slide insert and tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.
7.
CENTERLINE
OF HINGE
CENTERLINE
OF HINGE
Installation Instructions
I-CL00578 Rev 3
REV: 3 REV DATE: 8/02/2017
Page 1 of 4
3 1/8"
79.4
3/8"
9.6
3/4"
19
19 7/8"
504.8
1 3/4"
44.5
12"
304.8
Centerline of These Holes Vertically Inline with Center of Hinge
TOP OF DOOR
TOP OF
DOOR
Installation Sequence:
Use door prep above to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.
1.
Fasten closer body to door with power adjustment port towards hinge.
2.
Position slide track to frame face orientated with countersink visible open side facing down and with hold
3.
open stop end toward hinge edge of door. Slide end caps on, insert screw through end caps
and fasten to the frame.
Place slide arm on pinion shaft of closer so arm is positioned at a 45 degree angle out from door face.
4.
Secure arm with arm washer and arm screw.
5.
To properly preload closer, push arm towards door and secure other end of slide arm to track by screwing it
6.
to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against slide
insert and tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.
7.
TOP JAMB (PULL SIDE) MOUNTING APPLICATION (RIGHT HAND SHOWN) 120
DOOR PREP
NOTE: IF USER
WISHES
TO HAVE A
LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD
OPEN STOP
OR STOP ONLY
AWAY FROM
THE PIVOT
HINGE IN
INCREMENTS
OF 1/2" UNTIL
DESIRED
ANGLE IS
ACHIEVED.
NOTE
: REQUIRES
5918 DROP PLATE
WHERE THE HEAD
FRAME FACE IS
LESS THAN 3"
(REQUEST CUSTOM
TEMPLATE FROM
HAGER)
CENTERLINE
OF HINGE
Installation Instructions
I-CL00578 Rev 3
REV: 3 REV DATE: 8/02/2017
Page 2 of 4
B
21 5/16"
541.3
POCKET DEPTH 2-1/2"-5"
Mount track 1-1/16"
above top of door to
center of screw holes on
track
3 1/8"
79.4
3/8"
9.6
19 7/8"
504.8
1 3/4"
44.7
4"
101.6
4"
101.6
4"
101.6
9/32"
7.4
CENTERLINE OF THIS HOLE VERTICALLY INLINE WITH CENTER OF HINGE
TOP OF DOOR
TOP OF
DOOR
HOLES TO MOUNT CLOSER (CLOSER NOT SHOWN FOR CLARITY)
TOP JAMB (PULL SIDE) MOUNT (RIGHT HAND SHOWN) 120
CUSTOM DOOR PREP WITH 5918 PLATE
Installation Sequence:
Use template above to locate mounting holes on pocket wall and mount closer according to pull side
1.
application template. Drill 1/8" pilot holes for the self tapping screws.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.
2.
Fasten closer body to door with power adjustment nut away from hinge.
3.
Fasten slide track to pocket wall face with open side facing down and with hold open stop end away from
4.
hinge edge of door. Slide end caps on, orientated with countersink visible. Screw will go through end caps
as it fastens to the frame.
Connect slide arm to track by screwing it to the slide insert. DOOR MUST REMAIN IN CLOSED POSITION
5.
FOR FOLLOWING ASSEMBLY STEPS.
Swing arm toward closer and rest the hub of the arm on top of the closer pinion. Place a wrench on the
6.
bottom pinion of the closer and rotate away from the hinge (approx. 30 degrees). When the cutout of the
arm hub and the pinion line up, slide the arm hub down over the pinion and secure tightly with the
washer and screw. This pretensions the closer arm.
Loosen the stop only/hold open stop and open door to required opening angle. Close the door. Now slide
7.
the stop only/hold open stop back towards the hinge about 1/2" and tighten down the stop only/hold
open stop via set screw.
Pocket Pivots
6-1/2"
4-1/2" x 4-1/2" Hinges,
Swing Clear Hinges,
or 3/4" Offset Pivots
5"
Dim "B"
Pivot/Hinge Type
POCKET DOOR APPLICATION 90
OPEN DOOR INTO POCKET
NOTE: IF USER
WISHES
TO HAVE A
LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD
OPEN STOP
OR STOP ONLY
AWAY FROM
THE PIVOT
HINGE IN
INCREMENTS
OF 1/2" UNTIL
DESIRED
ANGLE IS
ACHIEVED.
5918
CENTERLINE
OF HINGE
Installation Sequence:
Use door prep above to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.
1.
Fasten closer body to 5918 plate with power adjustment port towards hinge.
2.
Position slide track to frame face orientated with countersink visible open side facing down and with hold
3.
open stop end toward hinge edge of door. Slide end caps on, insert screw through end caps
and fasten to the frame.
Place slide arm on pinion shaft of closer so arm is positioned at a 45 degree angle out from door face.
4.
Secure arm with arm washer and arm screw.
5.
To properly preload closer, push arm towards door and secure other end of slide arm to track by screwing it
6.
to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against slide
insert and tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.
7.
Installation Instructions
I-CL00578 Rev 3
REV: 3 REV DATE: 8/02/2017
Page 3 of 4
5200 DOOR CLOSER ADJUSTMENTS
Installation Instructions
I-CL00578 Rev 3
REV: 3 REV DATE: 8/02/2017
Page 4 of 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Hagerco 5200 Series Standard Slide Track Arms Installation guide

Hagerco
Brand
Hagerco
Model
5200 Series Standard Slide Track Arms
Type
Installation guide

Hagerco 5200 Series Standard Slide Track Arms are designed to provide reliable door control solutions for a variety of applications. With a hold-open feature and adjustable spring power, these arms ensure smooth and controlled door movement. They are suitable for both pull-side and top jamb mounting, offering versatility in installation. The arms' sturdy construction and easy adjustment make them ideal for commercial and residential use, ensuring optimal door operation and enhancing the overall functionality of your space.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents