Hagerco 5100 Series Standard Slide Track Arms Installation guide

Hagerco
Brand
Hagerco
Model
5100 Series Standard Slide Track Arms
Type
Installation guide
3 3/4"
94.7
CENTERLINE
OF HINGE
6"
152.2
CENTERLINE
OF HINGE
INCREMENTS
PARTS
OF 1/2" UNTIL
ORIENTATION SHOWN
TEMPLATE DOOR PREPPULL SIDE APPLICATION (RIGHT HAND SHOWN) 120
WITHOUT SLIDE ARM:
SIDE MOUNT SCREW
DESIRED
ANGLE IS
ACHIEVED.
NOTE: IF USER
WISHES
TO HAVE A
LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD
OPEN STOP
OR STOP ONLY
AWAY FROM
THE PIVOT
HINGE IN
WITH SLIDE ARM: SAME ASSEMBLY
ORIENTATION FOR ALL MOUNTS; SLIDE
INSERT/HOLD OPEN STOP MAY FLIP SIDES
DEPENDING ON HANDING; SIDE MOUNT
SCREW ORIENTATION SHOWN
REV: 7 REV DATE: 09/09/2020
I-CL00577 Rev 7
5100 Track Arm
Installation Instructions
Page 1 of 4
SLIDE ARM
UNIVERSAL END CAP
SLIDE TRACK
SLIDE ARM INSERT
SCREW
Stop Only
UNIVERSAL
HOLD OPEN STOP
END CAP
MOUNTING
SCREW
Installation Sequence:
Use door prep above to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.1.
Fasten closer body to door with power adjustment port towards hinge.2.
Position slide track to frame face orientated with countersink visible open side facing down and with hold 3.
open stop end toward hinge edge of door. Slide end caps on, insert screw through end caps
and fasten to the frame.
Place slide arm on pinion shaft of closer so arm is positioned at a 45 degree angle out from door face.4.
Secure arm with arm washer and arm screw.5.
To properly preload closer, push arm towards door and secure other end of slide arm to track by screwing 6.
it to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against
slide insert and tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.7.
9.7
TOP OF
DOOR
505.3
19 7/8"
TOP OF DOOR
27.9
1 1/8"
25.4
1"
1"
25.4
2 1/4"
57
3/8"
5"
127
SET SCREW
Hold Open Stop
Slide Insert
NOTE: REQUIRES 5114 DROP PLATE WHERE
THE HEAD FRAME FACE IS LESS THAN 3-1/2"
REFERENCE PAGE 3 FOR CUSTOM MOUNTING
FRAME FACE 3-1/2" OR GREATER
27
1 1/16"
TOP OF
DOOR
OF HINGE
CENTERLINE
82.6
3 1/4"
OF HINGE
CENTERLINE
6"
152.4
25.4
1"
127
5"
25.4
1"
505.3
19 7/8"
DOOR
TOP OF
3/8"
9.5
2 1/4"
57
Center Track On
Frame Soffit
19 7/8"
3 7/16"
86.7
INSIDE FACE OF SOFFIT
127
5"
25.4
1"
1"
25.4
2 1/4"
57
SOFFIT
BOTTOM OF
4 1/8"
104.6
505.3
22 7/8"
581.8
INSIDE FACE OF SOFFIT
Use door prep above to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.1.
Fasten closer body to door with power adjustment port away from hinge.2.
Position slide track to frame face orientated with countersink visible open side facing down and with hold 3.
open stop end toward hinge edge of door. Slide end caps on, insert screw through end caps
and fasten to the frame.
Place slide arm on pinion shaft of closer so arm is positioned at a 45 degree angle out from door face.4.
Secure arm with arm washer and arm screw.5.
To properly preload closer, push arm towards door and secure other end of slide arm to track by screwing 6.
it to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against
TOP JAMB (PULL SIDE) MOUNTING APPLICATION (RIGHT HAND SHOWN) 120 DOOR PREP
Installation Sequence:
7.
slide insert and tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.
SWING ANGLE,
SIMPLY
MOVE HOLD OPEN
STOP
OR STOP ONLY
AWAY FROM
THE PIVOT HINGE
IN INCREMENTS
OF 1/2" UNTIL
DESIRED ANGLE IS
ACHIEVED.
hinge edge of door. Slide end caps on. Install screw up through end caps and fasten to the frame.
Connect slide arm to track by screwing it to the slide insert. DOOR MUST REMAIN IN CLOSED POSITION 4.
FOR FOLLOWING ASSEMBLY STEPS.
Swing arm toward closer and rest the hub of the arm on top of the closer pinion. Place a wrench on the 5.
bottom pinion of the closer and rotate away from the hinge (approx. 30 degrees). When the cutout of the
arm hub and the pinion line up, slide the arm hub down over the pinion and secure tightly with the washer
and screw. This pretensions the closer arm.
Open door to required opening angle. Then slide stop only/hold open stop up against slider insert and
7.
tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.
DOOR PREP PUSH SIDE APPLICATION (RIGHT HAND SHOWN) 120
6.
Installation Sequence:
Use template to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.1.
Fasten closer body to door with power adjustment port away from hinge.2.
Position slide track to frame soffit with open side facing down and with hold open stop end toward3.
NOTE: IF USER
WISHES
TO HAVE A LESSER
NOTE: IF USER WISHES
TO HAVE A LESSER
SWING ANGLE, SIMPLY
MOVE HOLD OPEN
STOP
OR STOP ONLY AWAY
FROM
THE PIVOT HINGE IN
INCREMENTS
OF 1/2" UNTIL DESIRED
ANGLE IS ACHIEVED.
REV: 7 REV DATE: 09/09/2020
I-CL00577 Rev 7
5100 Track Arm
Installation Instructions
Page 2 of 4
: REQUIRES 5114 DROP PLATE WHERE
5114
NOTE
THE HEAD FRAME FACE IS LESS THAN 3-1/2"
HOLES TO MOUNT CLOSER
(CLOSER NOT SHOWN FOR CLARITY)
27
1 1/16"
OF HINGE
CENTERLINE
164.2
104.8
4 1/8" 4 1/8"
104.8
6 7/16"
DOOR
TOP OF
15.9
OF HINGE
CENTERLINE
82.6
3 1/4"
19 7/8"
505.3
5/8"
3/8"
9.5
TOP OF
DOOR
FRAME FACE LESS THAN 3-1/2"
Pocket Pivots 6-1/4"
Mount track 1-1/8"
above top of door to
center of screw holes on
track
"B"
Pocket Depth 2-1/2 - 5"
19 15/16"
506
REV: 7 REV DATE: 09/09/2020
I-CL00577 Rev 7
5100 Track Arm
Installation Instructions
Page 3 of 4
2.
3. Fasten closer body to door with power adjustment port away from hinge.
CUSTOM DOOR PREP WITH 5114 PLATETOP JAMB (PULL SIDE) MOUNT (RIGHT HAND SHOWN) 120
OPEN DOOR INTO POCKET POCKET DOOR APPLICATION 90
Fasten slide track to pocket wall face with open side facing down and with hold open stop end away from 4.
NOTE: IF USER
WISHES
TO HAVE A LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD OPEN
STOP
OR STOP ONLY
AWAY FROM
THE PIVOT HINGE IN
INCREMENTS
OF 1/2" UNTIL
DESIRED ANGLE IS
ACHIEVED.
hinge edge of door. Slide end caps on, orientated with countersink visible. Screw will go through end caps
as it fastens to the frame.
Connect slide arm to track by screwing it to the slide insert. DOOR MUST REMAIN IN CLOSED POSITION 5.
FOR FOLLOWING ASSEMBLY STEPS.
open stop via set screw.
Pivot/Hinge Type Dim "B"
5-1/2"
the stop only/hold open stop back towards the hinge about 1/2" and tighten down the stop only/hold
7.
or 3/4" Offset Pivots
Swing Clear Hinges,
4-1/2" x 4-1/2" Hinges,
Loosen the stop only/hold open stop and open door to required opening angle. Close the door. Now slide
washer and screw. This pretensions the closer arm.
arm hub and the pinion line up, slide the arm hub down over the pinion and secure tightly with the
bottom pinion of the closer and rotate away from the hinge (approx. 30 degrees). When the cutout of the
6. Swing arm toward closer and rest the hub of the arm on top of the closer pinion. Place a wrench on the
Installation Sequence:
Use template above to locate mounting holes on pocket wall and mount closer according to pull side 1.
application template on page 1. Drill 1/8" pilot holes for the self tapping screws.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.
Installation Sequence:
Use door prep above to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws.1.
Fasten closer body to 5114 plate with power adjustment port away from hinge.2.
Position slide track to frame face orientated with countersink visible open side facing down and with hold 3.
open stop end toward hinge edge of door. Slide end caps on, insert screw through end caps
and fasten to the frame.
Place slide arm on pinion shaft of closer so arm is positioned at a 45 degree angle out from door face.4.
Secure arm with arm washer and arm screw.5.
To properly preload closer, push arm towards door and secure other end of slide arm to track by screwing 6.
it to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against
slide insert and tighten down the stop only/hold open stop via set screw.
Determine door width, adjust spring power of closer by referencing closer adjustments on page 4.7.
5100 DOOR CLOSER ADJUSTMENTS
5100 Track Arm
Installation Instructions
I-CL00577 Rev 7
REV: 7 REV DATE: 09/09/2020 Page 4 of 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Hagerco 5100 Series Standard Slide Track Arms Installation guide

Hagerco
Brand
Hagerco
Model
5100 Series Standard Slide Track Arms
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents