Hagerco 5400 Series - Grade 2 Standard Duty - Surface Door Closer Installation guide

Brand: Hagerco

Model: 5400 Series - Grade 2 Standard Duty - Surface Door Closer

Category: Wall & ceiling mounts accessories

Type: Installation guide

7/16

(11.1mm)

5/16 (8mm)

3/8

(9.5mm)

3/8

(9.5mm)

3-3/

(85.7mm)

Pull Side of Door Pull Side of Door

Push Side of Door Push Side of Door

THIS IS A LEFT HAND DOOR

THIS IS A RIGHT HAND DOOR

CLOSIN

G SPEED

LATCHING

SPEED

CLOSING

VALVE

LATCH

VALVE

Regul

ar Arm Installation

Closer installs on PULL/HINGE

side of door

DOOR CLO

SER ADJUSTMENTS

NOTE Closing arcs("CLOSE"and"LATCH") are controlled by two(2)separate speed adjusting valves.

Adjust the CLOSING speed at first and then adjust the LATCHING speed.

1. "CLOSING"speed adjustment is accomplished by full rotations of the speed adjusting valve.

-Turn the speed adjusting valve CLOCKWISE for a SLOWER closing speed.

-Turn the speed adjusting valve COUNTER-CLOCKWISE for a FASTER closing speed.

2 "LATCH" speed adjustment is accomplished by full rotations of the speed adjusting valve.

-Turn the speed adjusting screw CLOCKWISE for a SLOWER closing speed.

-Turn the speed adjusting screw COUNTER-CLOCKWISE for a FASTER closing speed.

1. Select door opening angle and use dimensions shown above .

Mark four (4) holes on door for door closer and four(4) holes underside of frame for paralle l bracket.

2. Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.

Or drill and tap for 1/4-20 machine screws for metal door/frame.

3. Mount closer on door using provided screws.

SPEED ADJUSTING VALVE MUST BE POSITIONED AWAY FROM HINGE EDGE

4. Install parallel Arm Bracket to frame using provided screws.

5. Using a wrench on the square shaft at bottom of closer, rotate shaft approximately 45 degrees toward hinge edge of door.

Hold and place main arm on top shaft of closer at proper index mark as illustrated.

FOR LEFT HAND DOOR "L"(illustration " A"). FOR RIGHT HAND DOOR "R"(illustration "B").

Tighten arm screw with Lock-washer securely.

6. Remove arm shoe from forearm and discard. Install rod end of forearm to bracket using provided screw/washer assembly.

7. Adjust length of adjustable forearm so that main arm is parallel to frame.

8. Adjust the door closer, following instuctions as shown on page 1.

PARALLEL ARM (P

USH SIDE) Mounting

TO 180° OPENINGS.

Left hand door shown

Right hand door opposite

Dimensions are in inches (mm)

Do not scale drawing

Top Jamb Insta

llation

Closer Installs on Frame on

PUSH/STOP side of door.

Parallel A

rm Installation

Closer installs on PUSH/STOP

side of door. * Optional

3/4

(19mm)

Parallel bracket

9-1/16

(230.2mm)

2-3/4

(69.8mm)

OPENING

To 120

120 -180

DIM.A

10 3/4

(273mm)

6 15/16

(176.2mm)

4 3/4

(120.6mm)

8 3/4

(222.2mm)

DIM.B

Hinge or Pivot

Page: 1

age: 4

illustrated

Non Hold Open Arm

Left Hand Door-LH

Right Hand Reverse -RHR

See Page 2

illustrated

Non Hold Open Arm

Right Hand Door-RH

Left Hand Reverse -LHR

See Page 3

illustrated

Non Hold Open Arm

Right Hand Door-RH

Left Hand Reverse -LHR

See Page 4

Hinge Ed

of Door

Hinge Edge

of Door

5400 Series Non-Hold Open Door Closer

Installation Instructions

Adjust

able 2-5

CHART TO

DETERMINE HAND

OF DOOR

NOTE: T

hese instructions apply only to closers equipped with backcheck action.

To increase backcheck intensity, turn "BC" valve clockwise.

To decrease backcheck intensity , turn"BC" Valve counter-clockwise.

OPENING CYCLE

INCREASE

DECREASE

Never close This

valve completely

BACKCHECK ADJUSTMENT

Backcheck

Range

CLOSING CYCLE

*ADJUST SPRING TENSION ACCORDING TO THE

DOOR WIDTH & WEIGHT

INCREASE

DECREASE

NOTE: MAX 16 TURNS FROM MINIMUM SETTING

SPRING

OWER

FULL TURNS

OF SPRING

ADJUSTING

NUT

MAX

DOOR

WEIGHT

(kg)

1 -5

45 2 0

65 3 5

85 4 11

INSTALLATION SEQUENCE

(A) (B)

Parallel arm Insta

llation

Speed

screws

Right

hand door

Left hand door

45° 45°

HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149

I-CL00796 Rev. 4

6-12-2020

ADJUST SPRING TENSION ACCORDING TO THE

DOOR WIDTH & WEIGHT

6-1/2

(165.1mm)

1-3/4(44.4mm)

1(25.4mm)

9-1/16(230.2mm)

3/4(19mm)

1-1/8(28.5mm)

9-1/16(230.2mm)

3/4(19mm)

1/2(12.7mm)

6-1/14

(158.7mm)

1-3/4(44.4mm)

inge

Pivot

Righ

t hand door shown

Left hand door opposite

Dimensions are in inches(mm)

Do not scale drawing

PENING

To120

-18

6-1

/2(165.1mm)

DIM.A

4(101.6mm)

1. S

elect door opening angle and use dimensions shown above.

ark four (4) holes on door leaf for closer body and two (2) holes on frame for arm shoe.

Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.

Or drill and tap for 1/4-20 machine screws for metal door/frame

3. Install forearm/arm shoe assembly to frame using provided screws.

Mount closer on door using provided screws. SPEED ADJUSTING VALVE MUST BE POSITIONED TOWARD

HINGE EDGE

Install main arm to top pinion shaft, perpendicular to door. Secure tightly with provided arm screw/washer assembly.

Adjust length of forearm so that forearm is perpendicular to frame when assembled to preloaded main arm (see below

iIlustration). Secure forearm to main arm with provided screw/washer assembly

Snap pinion cap over shaft at bottom of closer. If the slim cover is packed, please fix it by provided screws.

Adjust the door closer, following instructions as shown on page 1.

INS

TALLATION

SEQU

ENCE

OTE: MAX 16 TURNS FROM MINIMUM SETTING

REGULAR ARM (PULL SIDE) Mounting

TO 180° OPENINGS.

inge

Pivot

TOP JAMB (PUSH SIDE) Mounting

TO 180° OPENINGS.

eft Hand Door

Right Hand Door

Top View Typical Installation

SPEED

ADJUSTING

SCREW

SPEED

ADJUSTING

SCREW

"BC"

ADJUSTING SCREW

Preload Preload

ight hand door Left hand door

PENING DIM. A

To 120

120 -

180

1/2(165.1mm)

4(101.6mm)

"BC"

ADJUSTING SCREW

Preload Preload

SPEED

ADJUSTING

SCREW

SPEED

ADJUSTING

SCREW

Top View Typical Installation

Page

: 2

Page: 3

Select door opening angle and use dimensions shown above.

Mark four (4) holes on door frame for closer body and two (2) holes on door leaf for arm shoe.

2. Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.

Or drill and tap for 1/4-20 machine screws for metal door/frame

3. Install forearm/arm shoe assembly to door leaf using provided screws.

4. Mount closer on door frame using provided screws. SPEED ADJUSTING VALVE MUST BE POSITIONED TOWARD

HINGE EDGE

5. Install main arm to bottom pinion shaft, perpendicular to door frame.

Secure it tightly with provided arm screw/washerassembly.

6. Adjust length of forearm so that forearm is perpendicular to door leaf when assembled to preloaded main arm (see below

iIlustration). Secure forearm to main arm with provided screw/washer assembly

7. Snap pinion cap over shaft at top of closer. If the slim cover is packed, please fix it by provided screws.

8. Adjust the door closer, following instructions as shown on page 1.

INS

TALLATION

SEQU

ENCE

Left hand door shown

Right hand door opposite

Dimensions are in inches(mm)

Do not scale drawing

ADJUST SPRING TENSION ACCORDING TO THE

DOOR WIDTH & WEIGHT

OTE: MAX 16 TURNS FROM MINIMUM SETTING

INCREASE

DECRE

ASE

SPRIN

POWER

FULL TURNS

OF SPRING

ADJUSTING

NUT

MAX

DOOR

WEIGHT

(kg)

2 -5

65 3 0

85 4 5

120 5 11

INCREASE

DECREA

SPRIN

POWER

FULL TURNS

OF SPRING

ADJUSTING

NUT

MAX

DOOR

WEIGHT

(kg)

2 -5

65 3 0

85 4 5

120 5 11

AGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149

HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149

ADJUST SPRING TENSION ACCORDING TO THE

DOOR WIDTH & WEIGHT

6-1/2

(165.1mm)

1-3/4(44.4mm)

1(25.4mm)

9-1/16(230.2mm)

3/4(19mm)

1-1/8(28.5mm)

9-1/16(230.2mm)

3/4(19mm)

1/2(12.7mm)

6-1/14

(158.7mm)

1-3/4(44.4mm)

inge

Pivot

Righ

t hand door shown

Left hand door opposite

Dimensions are in inches(mm)

Do not scale drawing

PENING

To120

-18

6-1

/2(165.1mm)

DIM.A

4(101.6mm)

1. Select door opening angle and use dimensions shown above.

Mark four (4) holes on door leaf for closer body and two (2) holes on frame for arm shoe.

2. Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.

Or drill and tap for 1/4-20 machine screws for metal door/frame

3. Install forearm/arm shoe assembly to frame using provided screws.

4. Mount closer on door using provided screws. SPEED ADJUSTING VALVE MUST BE POSITIONED TOWARD

HINGE EDGE

5. Install main arm to top pinion shaft, perpendicular to door. Secure tightly with provided arm screw/washer assembly.

6. Adjust length of forearm so that forearm is perpendicular to frame when assembled to preloaded main arm (see below

iIlustration). Secure forearm to main arm with provided screw/washer assembly

7. Snap pinion cap over shaft at bottom of closer. If the slim cover is packed, please fix it by provided screws.

8. Adjust the door closer, following instructions as shown on page 1.

INS

TALLATION

SEQU

ENCE

OTE: MAX 16 TURNS FROM MINIMUM SETTING

REGULAR ARM (PULL SIDE) Mounting

TO 180° OPENINGS.

inge

Pivot

TOP JAMB (PUSH SIDE) Mounting

TO 180° OPENINGS.

eft Hand Door

Right Hand Door

Top View Typical Installation

SPEED

ADJUSTING

SCREW

SPEED

ADJUSTING

SCREW

"BC"

ADJUSTING SCREW

Preload Preload

ight hand door Left hand door

PENING DIM. A

To 120

120 -

180

1/2(165.1mm)

4(101.6mm)

"BC"

ADJUSTING SCREW

Preload Preload

SPEED

ADJUSTING

SCREW

SPEED

ADJUSTING

SCREW

Top View Typical Installation

Page

: 2

Page: 3

1. S

elect door opening angle and use dimensions shown above.

ark four (4) holes on door frame for closer body and two (2) holes on door leaf for arm shoe.

Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.

r drill and tap for 1/4-20 machine screws for metal door/frame

Install forearm/arm shoe assembly to door leaf using provided screws.

4. Mount closer on door frame using provided screws. SPEED ADJUSTING VALVE MUST BE POSITIONED TOWARD

HINGE EDGE

Install main arm to bottom pinion shaft, perpendicular to door frame.

Secure it tightly with provided arm screw/washerassembly.

Adjust length of forearm so that forearm is perpendicular to door leaf when assembled to preloaded main arm (see below

iIlustration). Secure forearm to main arm with provided screw/washer assembly

Snap pinion cap over shaft at top of closer. If the slim cover is packed, please fix it by provided screws.

Adjust the door closer, following instructions as shown on page 1.

INS

TALLATION

SEQU

ENCE

Left hand door shown

Right hand door opposite

Dimensions are in inches(mm)

Do not scale drawing

ADJUST SPRING TENSION ACCORDING TO THE

DOOR WIDTH & WEIGHT

OTE: MAX 16 TURNS FROM MINIMUM SETTING

INCREASE

DECRE

ASE

SPRIN

POWER

FULL TURNS

OF SPRING

ADJUSTING

NUT

MAX

DOOR

WEIGHT

(kg)

2 -5

65 3 0

85 4 5

120 5 11

INCREASE

DECREA

SPRIN

POWER

FULL TURNS

OF SPRING

ADJUSTING

NUT

MAX

DOOR

WEIGHT

(kg)

2 -5

65 3 0

85 4 5

120 5 11

AGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149

HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149

7/16

(11.1mm)

5/16 (8mm)

3/8

(9.5mm)

3/8

(9.5mm)

3/8

(85.7mm)

Pull Side of Door Pull Side of Door

Push Side of Door Push Side of Door

THIS IS A LEFT HAND DOOR

THIS IS A RIGHT HAND DOOR

CLO

SING SPEED

LATCHING

SPEED

CLOSING

VALVE

LATCH

VALVE

Reg

ular Arm Installation

Closer installs on PULL/HINGE

side of door

OR CLOSER ADJUSTMENTS