Hagerco 5200 Series Double Egress Slide Track Arms Operating instructions

Hagerco
Brand
Hagerco
Model
5200 Series Double Egress Slide Track Arms
Type
Operating instructions

Hagerco 5200 Series Double Egress Slide Track Arms are designed for use on double egress doors and frames, pull side only. They are universally handed, so can be used on either left- or right-handed doors. The arms are adjustable, allowing you to customize the opening angle of the door. They also feature a hold-open stop, which can be used to keep the door open at a specific angle. The arms are easy to install and come with all the necessary hardware.

Here are some of the benefits of using Hagerco 5200 Series Double Egress Slide Track Arms:

  • They allow you to open the door from either side, making them ideal for use in emergency situations.

Hagerco 5200 Series Double Egress Slide Track Arms are designed for use on double egress doors and frames, pull side only. They are universally handed, so can be used on either left- or right-handed doors. The arms are adjustable, allowing you to customize the opening angle of the door. They also feature a hold-open stop, which can be used to keep the door open at a specific angle. The arms are easy to install and come with all the necessary hardware.

Here are some of the benefits of using Hagerco 5200 Series Double Egress Slide Track Arms:

  • They allow you to open the door from either side, making them ideal for use in emergency situations.
FOR
2-5/8"
EGRESS
Adjustable Rod
Connection Pin
Tube Arm
Set Screw
Small Arm (Universally Handed)
Screw to secure adjustable rod
to tube arm
19 7/8"
504.8
3 15/16"
100.8
12"
304.8
3/4"
19
1 15/16"
49.8
1 1/16"
27.2
3 7/8"
99
PARTS - DE TRACK ARM (RIGHT HAND SHOWN)
INSTALL DE TRACK ARM - PULL SIDE APPLICATION (RIGHT HAND SHOWN) 120
TEMPLATE
Installation Sequence:
Use template above to locate mounting holes on door and frame. Drill 1/8" pilot holes for the
1.
self tapping screws.
Determine door width, adjust spring power of closer by referencing closer installation
2.
instructions.
Fasten closer body to door with power adjustment nut toward hinge.
3.
Fasten slide track to frame face with open side facing down and with hold open stop end toward
4.
hinge edge of door.
Place slide arm on pinion shaft of closer at preload of 45 degrees out from door face.
5.
Secure arm with arm washer and arm screw.
6.
Push arm towards door to pretension closer then secure other end of slide arm to track by
7.
screwing it to the slide insert. Open door to required opening angle. Then slide stop only/hold
open stop up against slider insert and tighten down the stop only/hold open stop via set screw.
NOTE: IF USER
WISHES
TO HAVE A
LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD
OPEN STOP
OR STOP ONLY
AWAY FROM
THE PIVOT
HINGE IN
INCREMENTS
OF 1/2" UNTIL
DESIRED
ANGLE IS
ACHIEVED.
5200 Series DE Track Arm
Installation Instructions
I-CL00581
REV: 2 REV DATE: 1/23/18
Page 1 of 2
DOUBLE EGRESS ARM (RIGHT HAND SHOWN)
Installation instructions:
1. Universally handed DE arm is for installations on double egress doors and
frames, pull side only. For push side mountings on double egress frames, use
standard arm PA or Top Jamb mounting.
2. Reference instructions above for arm assembly. Right hand shown. For left hand
simply mirror the short arm 45 degrees to the opposite side of main arm.
3. Reference instructions on page 1 for specific mounting with closer
and track.
3. Put the
connecting
pin thru
the 2 holes
as shown.
2. Put the small arm with
L side up and align the
two holes to make a 45
degree angle between
the tube arm and small
arm.
1. Put the adjustable rod
into tube arm as shown.
5. Tighten the adjustable rod and
the tube together with the screw against
the actual dimmension.
4. Tighten the set screw.
EXPLODED
ASSEMBLED
5200 Series DE Track Arm
Installation Instructions
I-CL0058
REV: 2 REV DATE: 1/23/18
Page 2 of 2
  • Page 1 1
  • Page 2 2

Hagerco 5200 Series Double Egress Slide Track Arms Operating instructions

Hagerco
Brand
Hagerco
Model
5200 Series Double Egress Slide Track Arms
Type
Operating instructions

Hagerco 5200 Series Double Egress Slide Track Arms are designed for use on double egress doors and frames, pull side only. They are universally handed, so can be used on either left- or right-handed doors. The arms are adjustable, allowing you to customize the opening angle of the door. They also feature a hold-open stop, which can be used to keep the door open at a specific angle. The arms are easy to install and come with all the necessary hardware.

Here are some of the benefits of using Hagerco 5200 Series Double Egress Slide Track Arms:

  • They allow you to open the door from either side, making them ideal for use in emergency situations.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents