Zippity Outdoor Products ZP19008 Operating instructions

Brand
Zippity Outdoor Products
Model
ZP19008
Type
Operating instructions
Wilmington Vinyl Screen Kit 2 Pack
(36”W x 48”H)
ASSEMBLY INSTRUCTIONS
1
Ver 1.1/052015
Ground
10 in
18
1
2
in
18
1
2
in
4 in
36 in
48 in
3
4
in
1
2
in
1 in
1
1
2
in
32 in
33
3
8
in
7
8
in
1
1
2
in
If necessary, this enclosure can be trimmed down horizontally and vertically to fit your custom space.
Use a fine toothed circular or hack saw. Rails will need to be re-spaced and configured accordingly
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
2 Wilmington Vinyl Screen Instructions
GENERAL INFORMATION
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at
1 877 234 6196
(Mon. to Fri. 8:00 AM to 4:00 PM EST).
1.
Post Caps
(4)
2. Top and Bottom Rails
(
4) - 1½” x 1½“ x 36½”
3. Posts (4) - .875” x 1½” x 57½”
4.
Slats
(28) - ¼“ x 1½” x 41”
5.
Middle Rail (
2) - 1½“ x 1½” x 36½“
6.
Joiner Clips
(4)
7.
3/4” Self-Auguring Stainless Steel Screw
(32)
Tools You Will Need
• Cordless Drill
• Level
• Hammer
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
Please read through before starting assembly.
7
Not to Scale
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
1
4
2
3
2
5
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
6
3Wilmington Vinyl Screen Instructions
Identify the top and bottom rails (rails with holes on only one
side for vertical slats)
Position the two posts as illustrated and slide the top rail
(with holes facing up as illustrated) down over the posts
until the pre-drilled holes in rails are aligned with the
pre-drilled holes in both posts.
Tip!
Shine an LED light from smart phone or flashlight down the
end of the posts to help identify alignment of pre-drilled
holes if necessary.
Screw the top rail into both sides of both posts.
1
2
STEP ONE
2
Spear end facing up;
Orientate posts as illustrated
3
4
Slide the middle rail (with holes on both sides) over the
posts until the pre-drilled holes in the rail are aligned
with the pre-drilled holes in both posts.
Screw the middle rail into both sides of both posts.
Slide all vertical slats down thru the middle rail and
down into the top rail.
4
5
6
6
5
3
1
Holes for Vertical Slats Only on One Side
Slide the bottom rail (same as the top rail) over the posts and
begin aligning vertical slats one by one into the bottom rail.
Align the pre-drilled holes on the rail with the pre-drilled
holes in the posts and fasten with screws on both sides of post.
1
2
STEP TWO
1
2
4 Wilmington Vinyl Screen Instructions
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
5
STEP THREE
1
2
Install Screen into Ground
Move the screen to its final location and identify the location
of posts.
Attempt to push the unit into the ground as illustrated
1
x
x
2
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
Optionally:
1. If your ground is too hard, loosen the top 6” or 7” of the ground
with a claw hammer as illustrated.
2. Add water to loosened soil
3. Use a block of wood to the protect the top of post and
gently hammer the post into the ground.
Wilmington Vinyl Screen Instructions
Option 3:
x
x
Option 1:
Option 2:
x
x
Push down on the top of posts
with both hands
Block of Wood
Level
3
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
STEP THREE
3
Install Screen into Ground (Continued)
Level the screen as necessary and backfill excavated dirt and
tamp as necessary.
If your ground is really hard, you may need to dig a
hole large enough to accomodate one post from each
panel into the same hole - Approximately 8” in diameter
and 10” deep.
Backfill and compact the dirt.
6
Wilmington Vinyl Screen Instructions
8” Dia x 10” Deep
7
STEP FOUR
1
2
Fasten Joiner Clips
Fasten screens together by using joiner clips as illustrated.
Fasten the opposite end of the joiner clip as illustrated.
1
2
Angled Screens Application
Corner Screens Application
Wilmington Vinyl Screen Instructions
Top Rail
Bottom
Rail
Top Rail
Bottom
Rail
Top Rail
Bottom
Rail
1
10616 Bailey Road, Unit H, Cornelius NC 28031
Toll Free Phone: 1 877 234 6196 Fax: 704 631 4685
www.zippity-outdoor.com
8
STEP FIVE
1
Fasten Post Caps
Push the post caps down over the posts to lock into place.
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Zippity Outdoor Products ZP19008 Operating instructions

Brand
Zippity Outdoor Products
Model
ZP19008
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents