Zippity Outdoor Products ZP19026 Operating instructions

Brand
Zippity Outdoor Products
Model
ZP19026
Type
Operating instructions
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at
1 877 234 6196
(Mon. to Fri. 8:00 AM to 4:00 PM EST).
1.
Post Caps
(2)
2. Top Rail
(
1) - 1½” x 1½“ x 91 7/8”
3.
Posts
(2) - 7/8“ x 1½” x 41 ½”
4. Pickets
(20) - ¼” x 1½” x 38 3/8“
5. Bottom
Rail (
1) - 1½“ x 1½” x 91 7/8“
6. Metal U-
Joiner
(2)
7. Metal
Feet
(2)
8.
3/4” Self-Auguring Stainless Steel Screw
(8)
Tools You Will Need
• Cordless Drill
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
Zippity Lightweight Portable Vinyl Fence
Kit (42”H x 92”W)
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Ver 2.2/012318
1
3
2
4
5
Ground
This fence can easily be trimmed down horizontally
to fit your custom space. Use a fine toothed circular
saw or hack saw.
8
Not to Scale
6
92 in
44 1/2 in
2 5/8 in
6 in
29 1/2 in
42 in
46 in
40 7/8 in
7
2 in
3 1/2 in
2 3/8 in
14 in
2 in
12 1/2 in
1/2 in
Diameter.
3 1/8 in
Metal Feet Metal U-Joiner
2
Position the two rails as illustrated and slide the two posts
thru the large routed holes in the top and bottom rails until
the predrilled holes in both rails are aligned with the pre-
drilled holes in both posts.
Note the difference between the top and bottom rails.
Secure the rails to the post with screws on both sides of the
rails as illustrated.
1
2
STEP ONE
Zippity Lightweight Portable Vinyl Fence Kit Instructions
1
Note: Underside of Bottom Rail
Note: Align Holes
2
Bottom rail only has picket holes
on one side.
3
Zippity Lightweight Portable Vinyl Fence Kit Instructions
STEP TWO
1
Install Fence
Stand the fence assembly up as shown and align and insert the
two posts into the steel feet as shown.
1
Note: You may need to squeeze the metal prongs
slightly together for them to slip inside the posts.
4
Zippity Lightweight Portable Vinyl Fence Kit Instructions
2
2
STEP THREE
Please insert each picket down thru the top rail and into the
bottom rail.
Note: The tabs on the bottom of the pickets are intended to go
into the bottom rail to lock picket into place.
Finish the assembly by pushing the post caps down over the
top of posts as illustrated. The post caps will lock into place.
1
1
5
STEP THREE
1
Multiple Fence Panels Installation
For multiple fence panels installation, bring the two ends
close to each other and simply insert the U-Joiners through
the pre-drilled holes on both top and bottom rails as shown.
45° Application
90° Application
5
10616 Bailey Road, Unit H, Cornelius NC 28031
Toll Free Phone: 1 877 234 6196 Fax: 704 631 4685
www.zippity-outdoor.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Zippity Outdoor Products ZP19026 Operating instructions

Brand
Zippity Outdoor Products
Model
ZP19026
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents