UTEPO UTP1218-PSB150 Quick Installation Guide

Brand
UTEPO
Model
UTP1218-PSB150
Category
Network switches
Type
Quick Installation Guide
1
2
16-Port 100M PoE+ 2-Port 1000M RJ45 Ethernet Switch
User Manual
Please check the following items after unpacking, if any missing, please contact your local dealer.
Items
Quantity
Switch
1 pc
AC Power Cable
1 pc
Mounting Accessory
1 set
User Manual
1 pc
Product Overview
The product is 16-Port 100M PoE+ 2-Port 1000M RJ45
Ethernet Switch.
The switch provides 16 100M Ethernet RJ-45 downlink ports
and 2 Gigabit Ethernet RJ-45 uplink ports. All RJ-45 downlink
Ethernet ports support Power-over-Ethernet (PoE+) and
deliver up to 30W power per port.
The switch supports 3 working modes through DIP switch:
Default, VLAN and CCTV. It can be widely used in video
security monitoring systems, network projects, etc.
Dimensions (mm)
16-Port 100M PoE+ 2-Port 1000M RJ45 Ethernet Switch
Front Panel
Rear Panel
Indicators
Indicators
Status
Descriptions
Power
Power supply indicator
On
Power supply is on
Off
Power supply is off.
Link1~16
Downlink Ethernet ports link
indicators
On
The port is linking normally.
Blink
The port is transmitting or receiving data.
Off
The port links down.
G1, G2
Uplink Ethernet ports link indicators
On
The port is linking normally.
Off
The port links down.
PoE Max
PoE Power Limit Indicator
On
When the total PoE power provided by the ports
exceeds 130W, the indicator lights up.
When the total PoE power provided by the ports
exceeds 135W, the device will stop the PoE of the
port with the largest port number.
Off
When the total PoE power provided by the ports
does not exceed 130W, the indicator turns off.
Note:
The total PoE power that the PoE ports can provide is 135W. If it exceeds 135W, the PoE of the port with the
maximum port number will be cut off. In this case, please use a lower power device to replace the original one, or
take other measures to ensure the total PoE power less than 135W. And users need to re-plug one of the other
normal connection ports to restore the PoE of the port whose power is cut off.
DIP Switch
The support supports three working modes through DIP switch.
Interfaces
Descriptions
Default
All ports are free to communicate, transmission distance: 0~100m.
VLAN
Downlink ports are isolated from each other, but can communicate with uplink ports.
Transmission distance: 0~100m. Under this mode, the PoE watchdog function is
enabled.
CCTV
The transmission distance is extended up to 250m, but the rate is limited to 10Mbps.
Under this mode, the PoE watchdog function is enabled.
16-Port 100M PoE+ 2-Port 1000M RJ45 Ethernet Switch
16-Port 100M PoE+ 2-Port 1000M RJ45 Ethernet Switch
3
4
1) Before installation, power off the equipment. Installation when device is powered on is prohibited.
2) The switch supports rack mounted and desktop installation. Following with the rack-mounted installation steps:
Step 1: Fix the hangers on the side of the switch.
Accessories
2*
8*
Step 2: Install the switch on the rack. The distance between the devices should be more than 5cm.
3) After step 2) is completed, please use Cat5 or better cables to connect the switch and the device.
4) Check the installation and the wiring, after confirming that the connection is correct and reliable, power on the
switch.
The installation is completed.
Power on the system only after confirming that the wiring is correct, to avoid damage to the equipment. It is
recommended to use the power adapter and AC power cable to in the package to connect the power supply.
For better transmission performance, it is recommended to use Cat5 or better cables to connect the switch and
powered devices.
For better protection performance, it is recommended always to make the ground connection first and disconnect
it at the end when operating the device.
Each PoE RJ-45 port can provide a maximum power of 30W for a powered device. Please do not connect to a
powered device with a power exceeding 30W.
Before operating or maintaining the switch, please read the user manual carefully to avoid equipment damage
caused by misoperation.
Specifications
Items
16-Port 100M PoE+ 2-Port 1000M RJ45 Ethernet Switch
Hardware Specifications
Downlink Ports
16*10/100Base-TX PoE+ RJ-45 (Auto-MDI/MDI-X)
Uplink Ports
2*10/100/1000Base-T RJ-45 (Auto-MDI/MDI-X)
Led Indicators
1* power supply indicator, 1* PoE max indicator
16* downlink port indicators, 2*uplink port indicators
Cable
Cat5 or better
Dimensions (W*D*H)
294mm*180mm*44mm
Net Weight
1.6kg
Input Voltage
100~240V AC
Power Consumption
15W (Not include PoE)
Installation
Rack-mounted/wall-mounted
Material
Metal shell
Switch Property
Forwarding Modes
Store and Forward
Switching Capacity
7.2Gbps / non-blocking
Packet Forwarding Rate
5.4Mpps
MAC Table
8k, supported auto learning
Packet Buffer
4Mbit
PoE
PoE device
Endpoint PSE (Power Sourcing Equipment)
PoE Standard
IEEE 802.3af/at
PoE Pin Assignment
1/2(+), 3/6(-)
PoE Power Output
52V DC
PoE Budget
30W max for each port, 135W max for whole switch
Standard Conformance
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3x Flow Control
IEEE 802.3af Power Over Ethernet
IEEE 802.3at Power Over Ethernet
EMC
EMC
FCC 47 CFR Part 15 Class A
EN55032 Class A
IEC61000-4-2, Level 3: Contact Discharge: 6kV, Air Discharge: 8kV
IEC61000-4-3, Level 2: 3V/m
IEC61000-4-4, Level 2: 1kV
IEC61000-4-5, line to earth: 6kV
IEC61000-4-6, Level 2, (0.15MHz~80MHz)
LVD
LVD
EN 62368-1:2014
EN 62328-A11:2017
Environments
Operating
Temperature: -5 ~45
Relative Humidity: 5%~95% (Non-condensation)
Storage
Temperature: -40 ~75
Relative Humidity: 5%~95% (Non-condensation)
Certifications
Certifications
CE, FCC
Version: 13.238.101.2179, V1.0, updated 2021.8.5.
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
  • Page 1 1
  • Page 2 2

UTEPO UTP1218-PSB150 Quick Installation Guide

Brand
UTEPO
Model
UTP1218-PSB150
Category
Network switches
Type
Quick Installation Guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents