Greengate VNW-P-1001-DMV-V Installation guide

Brand: Greengate

Model: VNW-P-1001-DMV-V

Type: Installation guide

This manual is also suitable for

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Installation Instructions

LOAD 2

LOAD 1

120/277 VAC

BLACK

RED

BLUE

RED

NEUTRAL

GROUND

GREEN

Model # VNW-P-1001-DMV-W

Model # VNW-P-1001-DMV-V

Model # VNW-P-1001-DMV-G

NeoSwitch Passive Infrared (PIR)

Dual Relay Vacancy Sensing Wall Switch

(Ground Required)

• Readallinstructionsonbothsidesofthis

sheetfirst

• InstallinaccordancewithALLlocalcodes

• Forindooruseonly

Technology:PassiveInfrared(PIR)

Electrical Ratings:

120VAC:

• Incandescent/Tungsten–Max.load:6.7amps,

800W,50/60Hz

• Fluorescent/Ballast–Max.load:10amps,1200W,

50/60Hz

MotorLoad:¼HP@125VAC

277VAC:

• Fluorescent/Ballast–Max.load:9.8amps,

2700W,50/60Hz

Ballast Compatibility:Compatiblewithmagneticand

electronicballasts

No Minimum Load Requirement

Time Delays:Self-Adjusting,15seconds/test(10min

Auto),Selectable5,15,30minutes

Coverage:Majormotion–1000sq.ft.

Minormotion–300sq.ft.

Light Level Sensing:0to200foot-candles

Operating Environment:

• Temperature:32°F–104°F(0°C–40°C)

• RelativeHumidity:20%to90%non-condensing

Housing:Durable,injectionmoldedhousing.

PolycarbonateresincomplieswithUL94VO.

Size:

• MountingPlate/StrapDimensions:

4.195"Hx1.732"W(106.553mmx44mm)

• ProductHousingDimensions:2.618"Hx1.752"

Wx1.9"D(66.5mmx44.5mmx48.26mm)

LED Indicators:RedLEDindicatesPIRdetection;Green

LEDactsasEcoMeterornightlightlocator.

TheVNW-P-1001-DMVVacancySensingWallSwitchisaPassiveInfrared(PIR)motionsensinglightingcontrol

andconventionalwallswitchall-in-one,usedforenergysavingsandconvenience.

PIR Technology

Thesensor’ssegmentedlensdividesthefieldofviewintosensorzones,anddetectsthechangesintemperature

thatarecreatedwhenaperson,orpartofapersonassmallasahand,passesintooroutofasensorzone.

TheVNW-P-1001-DMVallowsthecontroloftwoseparateloadswithoneoccupancysensorswitch.

ThelightsareturnedONbypressingtheuniversallyrecognizedlighticonpushbutton.Ineithermode,the

lightsstayONaslongasthesensordetectsmotionintheroom.Whentheroomisvacated,thelightsturnOFF

automaticallyafterapresetTimeDelayinterval.

Thesensorincludesself-adaptivetechnologythatcontinuallyadjuststoconditionsbyadjustingsensitivityandtime

delayinreal-time.Byadjustingsensitivityandtimedelayautomatically,thesensorismaximizingthepotentialenergy

savingsthatareavailableintheparticularapplication.

TheEcoMeterprovidesavisualindicatorofenergyusage,increasingenduserawarenessandreminding

individualstotakecontroloftheirlightingtomaximizeenergysavings.

TheDaylightingfeaturepreventslightsfromturningON,

whentheroomisadequatelyilluminatedbynaturallight.

BathroomMode–Whenselected,bathroommodekeepsthesecondrelayONforanadditional8minutes,after

thefirstrelayhasbeenturnedoff.Combinethiswithchangingthepushbuttontothelight/fangraphicandyounow

havetheuniversallyrecognizedandeasytousebathroomsolution.

RelaySwapOption–Acommonprobleminelectricwiringiswiringthewrongswitchtothewrongload.Thiscan

makecontrolofloadsconfusingtoanenduser.TheRelaySwapoptionsolvestheproblembyallowingtheswitch

buttonsonthefaceoftheunittobeswapped,aftertheunitiswiredandinstalled.

TheVNW-P-1001-DMVisdesignedforofficesupto300squarefeet.

WheninstallingtheVNW-P-1001-DMVinanewjunctionbox,choosetheswitchlocationcarefullytoprovideoptimum

coverageoftheoccupiedarea.Whenreplacinganexistingwallswitch,bearinmindthattheremustbeaclearline-of-

sightbetweenthesensorandtheareatobecovered.AvoidpointingtheVNW-P-1001-DMVdirectlyintothehallway

whereitmaydetectpassers-by.

TheVNW-P-1001-DMVcanbeinstalledinanystandardsinglegangbox.It

maybeinstalledinthesamemannerasanordinarywallswitch.

• WiretheVNW-P-1001-DMVasdescribedinthewiringsection.

• MounttheVNW-P-1001-DMVinthejunctionbox.

CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned

OFF at the branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used as the

main switch for a fluorescent lighting circuit, the circuit breaker should be marked “SWD.” All installations

should be in compliance with the National Electric Code and all state and local codes.

NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact fluorescent lamps (CFLs) is

shortened by frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the

effects of cycling.

1.MakesurepoweristurnedOFFatthebranchcircuitbreaker.

2.Wireunitsasshowninwiringdiagramsperapplicablevoltagerequirements.

3.Mountunittowallbox.

4.TurnpowerbackONatthebranchcircuitbreakerandwait2minutesfortheunittostabilize.

5.Makenecessaryadjustments.(SeeCheckoutandAdjustmentssection)

6.Installwallswitchplate.

EcoMeter Operation

Load 1 Load 2 EcoMeter LED

OFF OFF 100%

ON OFF 50%

OFF ON 50%

ON ON OFF

Action EcoMeter Benefit

Apersonentersthespaceandoneof

theloadsisactivated

50% Increasedawarenessofenergysavings

BothloadsareON OFF

Theareaisvacatedandthelightsturn

OFFautomatically

100%

Increasedawarenessofenergysavings;

Actsasanightlightlocator

ApersonturnsthelightsOFF

manuallyuponexitinganarea

100%

Increasedawarenessofenergysavings

andremindsindividualstotakecontrol

oftheirlightingforadditionalsavings;

Actsasanightlightlocator

Ifthedaylightingfunctionisactivated

foroneofthetwoloadsandthereis

sufficientdaylightinthespace,theunit

willholdthatloadOFF

50%

Increasedawarenessofenergy

savings;Letspersonsknowthatthe

daylightsensorisholdingthelightsOFF;

Actsasanightlightlocator

Ifthedaylightingfunctionisactivated

forbothloadsandthereissufficient

daylightinthespace,theunitwillhold

thatloadsOFF

100%

Increasedawarenessofenergy

savings;Letspersonsknowthatthe

daylightsensorisholdingthelightsOFF;

Actsasanightlightlocator

Wiring Diagram 1: 120/277 VAC dual level single circuit wiring diagram

Maximum coverage area may

vary somewhat according to room

shape and the presence of obstacles.

Minor Motion, IR

Major Motion, IR

P/N 9850-000287-02

LOAD 2

LOAD 1

BLACK

RED

BLUE

RED

NEUTRAL (CIRCUIT 1)

NEUTRAL (CIRCUIT 2)

GROUND

CIRCUIT 1

GREEN

CIRCUIT 1

120/277 VAC

CIRCUIT 2

120/277 VAC

Wiring Diagram 2: 120/277 VAC dual level dual circuit wiring diagram

Coverage

Description

Speciﬁcations

General Information

Location

Installation

Wiring

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Printed in Malaysia

PIR Sensitivity

1.Standindifferentareasoftheroomandwaveyourhands.

2.IftheRedLEDdoesnotturnON,checkforanyobstructions.

3.Standstillthreetofourfeetawayfromsensorforfiveseconds.LEDshouldnotturnON.

4.IfRedLEDturnsONwithoutmotionorisconstantlyONadjustPIRsensitivityto50%bymovingDIPSwitch5up.

Field-of-view outside the space

1.AdjustPIRsensitivityto50%bymovingDIPSwitch5up.

2.Usenon-reflectivetapestripstocovertheportionsofthesensorlensthatviewoutsidethespace.

Daylight Adjustments

TheDaylightingfeaturepreventsthelightsfromturningONwhentheroomisadequatelyilluminatedbynaturallight.

Ifthereisenoughlightintheroomregardlessofoccupancy,thesensorwillholdthelightsOFF.Ifthereisnotenough

lightintheroom,thesensorwillallowthelightstoturnON.TheDaylightingfeatureallowstheselectionofwhichrelayto

controlviadaylighting(dualloadmodelsonly).ThesensorwillnotallowtheDaylightingfeaturetoturntheloadOFFuntil

thespaceisvacantifthelightlevelrisesabovethesetpointandtheTimeDelayexpires.Ifsomeoneattemptstoturnthe

load

ONandthereissufficientdaylightavailabletheDaylightingfeaturewillholdthelightsOFF.

1.Setthelightlevelwhentheambientlightisatthelevelwherenoartificiallightisneeded.Ifthisfeatureisnot

needed,leavethelightlevelatmaximum(fullyCW).

2.SetDIPSwitches11(Relay1)and/or12(Relay2)for

daylightcontrol.

3.Withtheload(s)ON,putthesensorintoTestMode.To

placeintoTestMode,toggleDIPSwitch12outofits

currentposition,wait3secondsandthenbackintoits

originalposition.

4.Setthelightleveltominimum(fullyCCW).

5.Letthesensortime-outsolightsareOFF.Enterthe

spaceandlightsshouldremainOFF.

6.MakesurenottoblockthesensorfromthedaylightsourceandadjustthelightlevelpotentiometerCWinsmall

increments.(Pause5secondsbetweeneachadjustment)

7.LightswillnotturnONuponmanualactivation,whentheambientlightlevelexceedsthedaylightthresholdsetting.

Time Delay Adjustments

Peoplewhoremainverystillforlongperiodsoftimemay

needalongertimedelaythanthedefaultsettingof10minutes.

Aslongastheself-adjustingfeatureisenabled,theswitch

will

respondtoeachpairoffalse-offswithnonormalOFFin

between,byalternatelymakingslightadjustmentstoeithertime

delay(by2minuteincrements)orsensitivity,sothereshouldbe

noneedformanualadjustment.Ifmanualadjustmentisdesired,

refertoTimeDelaysettingsinDIPSwitchlegend.

ResetsensorTimeDelaytofactorysettingsbymovingDIP

Switches1and2down.(IfDIPSwitches1and2arealready

down,toggleDIPSwitch1outofitscurrentposition,wait3seconds,andthenbacktoitsoriginalposition)

Override

TheOverridesettingallowsthesensortooperateasaserviceswitchintheunlikelyeventoffailure.

1.MoveDIPSwitch8up.

2.ThepushbuttoncanbeusedtomanuallyturnlightsONorOFF.

4.Walkoutsidetheroomandwait15secondsforthelightstoturnOFF.(IflightsdonotturnOFFgotoInstaller

AdjustmentsSection)

5.Re-entertheroomandmanuallyactivatethesensor.(IflightsdonotturnONgotoTroubleshootingSection)

6.Atthispointyoucanexittheroomandletthesensortime-out.Whenthesensortimes-outandisinactiveforfive

minutes,theunitwillgotoa10minuteTimeDelayusermodesetting.

Note:

ToplaceintoTestMode,toggleDIPSwitch12outofitscurrentposition,wait3seconds,andthenbackintoitsoriginalposition.

LOAD 2

LOAD 1

BLACK

RED

BLUE

RED

NEUTRAL

THREE-WAY WIRING DIAGRAM:

LIGHTS WILL TURN OFF, WHEN UNIT THAT WAS TURNED ON LAST AND/OR DETECTED MOTION LAST TIMES-OUT

GROUND

GREEN

120/277 VAC

BLACK

RED

BLUE

RED

GROUND

GREEN

TRAVELER

WIRES

Wiring Diagram 3: 120/277 VAC dual level single circuit three-way wiring diagram

CAUTION: If a room is wired for two circuits using two separate hot leads, it is very important to connect only

one circuit per relay. Both circuits must be fed from the same phase.

Issue Possible Causes Suggestions

Lights

Will Not

Turn ON

manually

DaylightFeatureEnabled

IfalllightsarerequiredadjustDIPSwitches

11and12and/ordaylightpotentiometer.

Powerinterruption Checkincomingvoltageand/orwiring.

If lights will still not turn ON, set sensor to override mode and call Technical Services at 1-800-553-3879

Lights

Will Not

Turn OFF

automatically

Override

MakesuresensorisnotinOverrideMode

(DIPSwitch8up).

Self-Adjust

IfsensorisinSelf-AdjustMode,itmaybepossibleforthe

unittohaveincreasedtheTimeDelaytoa30minutedelay.

IfthelightsdonotturnOFFafter30minutesfollownextstep.

30MinuteDelay

MaximumTimeDelayis30Minutes.CheckDIPSwitches

toverifyDIPSwitchsettings.IflightsdonotturnOFFatthe

setTimeDelay,checknextstep.

PIRactivatedbyheatsourceotherthanoccupant MoveDIPSwitch5up.

Lights

Will Not

Turn OFF

manually

CallTechnicalServices

If lights will still not turn OFF, call Technical Services at 1-800-553-3879

5 Minutes

Auto*

*Self-Adjusts to

10 min. user

mode

Time Delay

DIP Switch

Not Used PIR Sensitivity EcoMeterBathroom Relay SwapDaylighting

Relay 1Relay 2

Override

Default =

30 Minutes

15 Minutes

DIP Switch Legend





Disable

Enable





Disable

Enable





Disable

Enable

643













Full

50%





Disable

Enable





Enable

Disable





Normal

Swap

12345678910

11 12

Not Used

11 and 12

12345678910

11 12

34567891011

1 and 2

AdjustmentsshouldbemadewiththeHVACsystemonsothattheinstallerwillbeabletodetecttheeffectof

airflowontheoperationoftheVNW-P-1001-DMV.Useonlyinsulatedtoolstomakeadjustments.

Immediatelyafterapplyingpowertothelighting

circuit,waitapproximatelytwominutesfortheswitch

topowerupandstabilize.

Self-Adjust

SensorisshippedinSelf-AdjustMode.Thisapplies

totimedelayandPIRsensitivity.Inpreparationforthe

InstallerTest,thetimedelayissetto15seconds,after

thesensorisinstalled,poweredONandhasstabilized,

theunitwilltime-out15secondsafterthelastmotion

detected.Coverageandsensitivitycanbeconfirmedby

watchingtheRed(PIR)indicatorLEDonthefrontofthe

sensor,whilemovingaroundtheroom.

1.WalkaroundtheroomandmonitorLEDs.

2.Standindifferentpartsoftheroomandwave

yourhands.LEDshouldonlyturnONforone

secondwitheachmotion.(IfLEDdoesnotturn

ON,gotoInstallerAdjustments–Sensitivity

AdjustmentSection)

3.Standstillthreetofourfeetawayfromsensorfor

fiveseconds.LEDshouldnotturnON.(IfLEDturnsON,gotoInstallerAdjustments–Sensitivity

Adjustmentssection)

EcoMeter

ON/OFF Buttons

1 & 2

PIR Lens

DIP Switches

Daylight

Sensor Level

Adjustment

Red (PIR)

Detection LED

Checkout and Adjustment

DIP Switch Settings

Installer Adjustments

Troubleshooting

Warranties and Limitation of Liability

Pleaserefertowww.coopercontrol.comundertheLegalsectionforourtermsandconditions.

Greengate VNW-P-1001-DMV-V Installation guide

Brand: Greengate

Model: VNW-P-1001-DMV-V

Type: Installation guide

This manual is also suitable for

Download PDF

report

Greengate VNW-P-1001-DMV-V Installation guide

This manual is also suitable for

Greengate VNW-P-1001-DMV-V Installation guide

Related papers

Other documents