NEC NP-P474U Installation guide

NP-P474U
NEC
Brand
NEC
Model
NP-P474U
Category
Projector mounts
Type
Installation guide

This manual is also suitable for

ISSUED: 10-01-10 SHEET #: 056-9034-7 05-08-2015
Visit the Peerless Web Site at www.peerlessmounts.com
1 of 9
For customer care call 1-800-865-2112
Installation and Assembly Manual:
Custom Ceiling Mount for NP-M332XS, NP-M352WS, NP-M282X,
NP-M283X, NP-M322X, NP-M323X, NP-M322W, NP-M323W, NP-
M363X, NP-M363W, NP-M402X, NP-M403X, NP-M402H, NP-M403H,
NP-P401W, NP-P451X, NP-P451W, NP-P501X Projectors
Model: MP300CM
Features:
• ImageLock
TM
alignment prevents picture sag or drift
• Wrenchaccessslotforeasierushmountinstallations
• Exclusive aluminum track quick release
NEC Display Solutions of America, Inc.
Max UL Load Capacity: 50 lb (22.7 kg)
ISSUED: 10-01-10 SHEET #: 056-9034-7 05-08-2015
Visit the Peerless Web Site at www.peerlessmounts.com
2 of 9
For customer care call 1-800-865-2112
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Extension Columns / Ceiling Plate ...................................................................................................................4
Installation to Wood Joist Ceilings ..........................................................................................................................................5
Installation to Concrete Ceilings .............................................................................................................................................6
Attaching Adapter Plate to Projector.......................................................................................................................................7
Attaching Adapter Plate to Projector Mount............................................................................................................................8
Projector Alignment ................................................................................................................................................................9
Tools Needed for Assembly
• studnder("edgetoedge"studnderisrecommended)
• phillips screwdriver
• drill
• 5/16"bitforconcretesurface
• 5/32"bitforwoodstuds
• level
NOTE: Read entire instruction sheet before you start installation and assembly.
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity. See page 1.
• If mounting to wood joist ceilings, make sure that mounting screws are anchored into the center of the joist. Use of
an"edgetoedge"studnderishighlyrecommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed and intended to be mounted to the following supporting surfaces checked below with
thehardwareincludedinthisproductasspeciedintheinstallationsheet.Tomountthisproducttoanalternative
supporting surface, contact Peerless customer care at 1-800-865-2112.
• This product was designed to be installed on the following ceiling construction only;
CEILING CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x Wood Stud None
x Wood Joist None
x Solid Concrete None
Cinder Block Contact Customer Service
Brick Contact Customer Service
Otherorunsure? ContactCustomerService
WARNING
ISSUED: 10-01-10 SHEET #: 056-9034-7 05-08-2015
Visit the Peerless Web Site at www.peerlessmounts.com
3 of 9
For customer care call 1-800-865-2112
Description Qty. Part #
A
projector mount assembly 1
054-2171
B
4 mm security allen wrench 1
560-9646
C
#10-32x3/8"serratedwasherheadsocketpinscrew 2
520-2151
D
#10-32x1/4"socketpinscrew 1
520-2196
E
flat washer
2 540-1078
F
#14 x 2.5 phillips hex head wood screw 2
5S1-015-C04
G concrete anchor 2 590-0320
A
A
adapter plate 1 055-2985
BB M4 x 16 mm serrated socket pin screw 3 510-2087
CC retaining spacer 3 590-2009
DD 2 mm allen wrench 1 560-1097
EE
connection block 1 580-4065
Parts List
NOTE: Actual parts may appear slightly different than illustrated.
Before you start check the parts list to insure all of the parts shown are included.
C
A
D
G
E F
CC
BB
B
DD
EE
AA
ISSUED: 10-01-10 SHEET #: 056-9034-7 05-08-2015
Visit the Peerless Web Site at www.peerlessmounts.com
4 of 9
For customer care call 1-800-865-2112
Installation to Extension Column / Ceiling Plate
NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to
ceiling.
Screw projector mount assembly (A) onto extension column as shown in gure 1.1. Tighten swivel stop screw
againstextensioncolumn,ushmounttubeorreducerusing4mmsecurityallenwrench(B) as shown in gure
1.2.
NOTE: Swivelstopscrewisusedtojamagainstthreadsofextensioncolumn,ushmounttubeorreducerto
prevent any excess movement of projector mount assembly (A). Do not overtighten screw; overtightening screw
willdamagethreadsmakingitdifculttoseparateproducts.
Skip to step 4.
1
g. 1.1
g. 1.2
A
1-1/2"EXTENSIONCOLUMN
(SOLDSEPARATELY)
(ULLISTEDEXTORAECSERIES)
ARROWINDICATES
FRONTOFMOUNT
SWIVELSTOPSCREW
CMJ 455
(SOLDSEPARATELY)
ISSUED: 10-01-10 SHEET #: 056-9034-7 05-08-2015
Visit the Peerless Web Site at www.peerlessmounts.com
5 of 9
For customer care call 1-800-865-2112
Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes.
Makesurethatthemountingholesareinthecenterofthewoodjoist.Drilltwo5/32"(4mm)dia.holestoa
minimumdepthof2.5"(64mm).Attachprojectormountassembly(A)withtwo#14x2.5"woodscrews(F) and
twoatwashers(E) as shown in gure 2.1 or gure 2.2 depending on joist orientation.
NOTE: Mounting slots on projector mount assembly allow for 30° (±15°) of swivel adjustment before fully securing
wood screws.
Tighten wood screws (F)using3/8"(10mm)socketwrench,phillipsscrewdriveror10mmopenendwrenchuntil
projector mount assembly (A)isrmlyattached.
Skip to step 4.
Installation To Wood Joist Ceilings
2
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tightenwoodscrewssothatprojectormountassemblyisrmlyattached,butdonotovertighten.Overtightening
can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan"edgetoedge"studnder
is highly recommended.
• When installing Peerless ceiling mounts on a wood joist/beam covered with gypsum board (drywall), verify that the
joistsorbeamsareaminimumof2"x4"nominalsize.Donotinstallovergypsumboardthickerthan5/8".
WARNING
F
F
A
WOODJOIST
FRONTOF
MOUNT
E
E
WOODJOIST
A
ACCESSSLOTFOR
OPENENDWRENCH
ALLOWSTIGHTENING
OFWOODSCREW
g. 2.1
g. 2.2
ARROWONTOPOF
PROJECTORMOUNT
ASSEMBLYINDICATES
FRONTOFMOUNT
ISSUED: 10-01-10 SHEET #: 056-9034-7 05-08-2015
Visit the Peerless Web Site at www.peerlessmounts.com
6 of 9
For customer care call 1-800-865-2112
g. 3.1
Installation to Concrete Ceilings
Place projector mount assembly (A) on ceiling
as a template and mark the center of the two
mountingholes.Drilltwo5/16"(8mm)dia.holes
toaminimumdepthof2-1/2"(64mm).Attach
projector mount assembly (A) using two concrete
anchors (G),twoatwashers(E), and two #14 x
2-1/2"woodscrews(F) as shown in gure 3.1.
NOTE: Mounting slots on projector mount
assembly allow for 30° (±15°) of swivel adjustment
before fully securing wood screws.
Tighten wood screws (F)using3/8"(10mm)socket
or open end wrench or phillips screwdriver until
projector mount assembly (A)isrmlyattached.
3
• WheninstallingPeerlessceilingmountsonaconcreteceiling,theceilingmustbeatleast8"thickwithaminimum
compressive strength of 2000 psi. Never attach concrete expansion anchors to concrete covered with plaster,
drywall,orothernishingmaterial.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
WARNING
• Tightenwoodscrewsrmly,butdonotovertighten.
Overtighteningcandamagethescrews,greatly
reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
G
F
E
A
CONCRETECEILING
ARROWONTOP
OFPROJECTOR
MOUNTASSEMBLY
INDICATESFRONT
OFMOUNT
1
3
G
Drill holes and insert anchors (G).
Place plate (A) over anchors (G) and secure with screws (F).
Tighten all fasteners.
2
G
A
F E
concrete
surface
ISSUED: 10-01-10 SHEET #: 056-9034-7 05-08-2015
Visit the Peerless Web Site at www.peerlessmounts.com
7 of 9
For customer care call 1-800-865-2112
Align shoulder on connection block (EE) opposite
notch in adapter plate (AA). Attach adapter plate
(AA) to connection block (EE) using two #10-32 x
3/8"serratedwasherheadsocketpinscrews(C)
asshowningure4.1.Tightenscrewsusing4mm
allen wrench (B).
C
NOTCHINDICATES
FRONTOFPROJECTOR
SHOULDER
Attaching Adapter Plate to Projector
g. 4.1
BB
Flip projector upside down and attach adapter plate (AA) using four serrated socket pin screws (BB) and retaining
spacers (CC) as shown below. Tighten using 4 mm allen wrench (B).
NOTE: Retaining spacers (CC) go between the projector and adapter plate (AA).
AA
CC
AA
EE
5
4
ISSUED: 10-01-10 SHEET #: 056-9034-7 05-08-2015
Visit the Peerless Web Site at www.peerlessmounts.com
8 of 9
For customer care call 1-800-865-2112
Slide connection block (EE) with projector into projector mount assembly (A) as shown. Tighten captive screw to
secure projector to projector mount assembly (A).
IMPORTANT:Forsecurityinstallations,insertone#10-32x1/4"socketpinscrew(D) through projector mount
assembly (A) and into connection block (EE) as shown in detail 1. Tighten screw using 4mm security allen
wrench (B).
A
D
• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely
handle placement of the screen.
WARNING
Attaching Adapter Plate to Projector Mount
DETAIL 1
EE
7
A
FRONTOFMOUNT
CAPTIVE SCREW
ARROWINDICATES
FRONTOFMOUNT
EE
6
ISSUED: 10-01-10 SHEET #: 056-9034-7 05-08-2015
Visit the Peerless Web Site at www.peerlessmounts.com
9 of 9
For customer care call 1-800-865-2112
SCREWFORYAW(SWIVEL)STOP
(REFERTOSTEP1,INSTALLATION
TOEXTENSIONCOLUMNS,FIG.1.2)
KNOBFORROLL
ADJUSTMENT
KNOBFORPITCH
ADJUSTMENT
BACKOFMOUNT
ARROWINDICATES
FRONTOFMOUNT
To adjust yaw (swivel) for wood stud and concrete ceiling: Loosen wood screws (F)ifushmountedtowood
joists (page 5) or concrete ceilings (page 6), until projector mount can be rotated. Rotate mount to desired
position and retighten screws.
To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A)
indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and
turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand for
easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
A
To prevent tampering with the pitch and roll adjustments: Tighten the two tamper resistant security screws
on the projector mount assembly using 4 mm security allen wrench (B) to lock the pitch and roll adjustments as
shown below. Note:Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagethemount.
SIDE VIEW
Projector Alignment
8-1
TOLOCKPITCH,TIGHTEN
TAMPER RESISTANT
SECURITYSCREW
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
• Do not adjust pitch or roll while tamper resistant security screws are fully engaged.
• Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly
or damage may occur.
CAUTION
8
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

NEC NP-P474U Installation guide

NP-P474U
NEC
Brand
NEC
Model
NP-P474U
Category
Projector mounts
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents