ViziT VIZIT-MB1PE Operating instructions

Brand: ViziT

Model: VIZIT-MB1PE

Type: Operating instructions

VIZIT-MB

1PE

OPERATING INSTRUCTION

1PEMounting Box (the Box hereinafter) is intended for use as a housing for trademarked doorphone /

video doorphone units. The Box has a built-in socket outlet to connect units to the supply mains.

The Box is capable to house the following combinations of units:

- one control unit / power supply unit and one commutator / distribution amplifier ; or

- one control unit and one power supply unit.

If two units installed in the Box need the mains power, use a two Euro sockets adapter plug, e.g. BRENNENSTUHL

1508030 (the adapter plug is not supplied).

VIZIT

Note.

Figure Mounting Box VIZIT-MB1PE appearance and mounting dimensions1 -

Housing

Doorphone communication cables inlets

Protective bonding terminals to connect the

door to the

Door

Terminal

Lugs to hook the Box on a DIN-rail inside a

wiring closet

Terminal to connect the housing to the

mains cable’s protective (PE) conductor

to connect

uilt-in fuse protects the mains

socket outlet of the Box in case of current

overload / short circuits.

Padlock lug

to connect the

Cable gland

Fused terminal block the mains

cable. The b

Mains socket outlet

Seals for cable inlet

housing

doorstation’s PE

conductor

Brackets for fixing on a wall

Figure Adapter plug with two Euro sockets2 -

www. VIZIT-MB1PE Operating Instruction (revision 6 05)vizit-group.com 61/201 -

710

SPECIFICATIONS

OPERATING CONDITIONS

PARTS LIST

MB1PE

SAFETY INSTRUCTIONS

INSTALLATION

Ambient temperature range + to +

Relative humidity of air up to at

Mounting Box pc.

Fastening kit pc.

Operating Instruction pc.

1°C 4 °C

93% 25°C

VIZIT- 1

Rated mains voltage

Rated mains frequency

Maximum power consumption of

units installed in the Box

Maximum current consumption of

units installed in the Box

Ingress protection rating

Class

Dimensions (W)x(H)x(D) x x

Weight

When the mains power is on, the Box contains dangerous for life mains voltage - .

To avoid electric shock the Box shall be connected to the main protective (PE) conductor of a building using the mains

cable PE conductor.

The mains cable shall be protected against current overload by a single-pole or double-pole circuit breaker (with rated

current from 3Ato 6A).Asingle-pole circuit breaker

Mains power shall be off when connecting the Box to the supply mains.

Before performing any wiring or repair inside the Box, make sure that the control unit’s / power supply unit’s plug is

disconnected from the mains socket outlet.

The Box shall not be exposed to dripping or splashing, and no objects filled with liquids shall be placed on the Box.

No metallic objects shall penetrate into ventilation openings of the Box.

The Box shall be installed in heated premises with proper ventilation. The Box may be installed either on a wall, or on a

DIN-rail inside a wiring closet.

B , f gland to housing .

body of the gland , lock .

VAC

0.34 A

343 mm

2.5 kg

WARNING! 230 V

For qualified installation, wiring and servicing refer to technical and commercial partners of VIZIT TM. The list of

companies is given on VIZIT.EU ( .

WARNING! Do not mount the Box near heating equipment!

VIZIT

efore mounting the Box asten the cable supplied the (see Fig. 3)

Put the (1) cable into the hole (2) and tighten the nut (3)

IP20

251 93

http://vizit.eu/eurounion/)

230

shall be connected to the phase wire.

www. VIZIT-MB1PE Operating Instruction (revision )vizit-group.com 2 6/201 -605

Figure 3 Fixing the cable gland–

4Sealing nut

Body

Hole

Lock nut

Mounting on a wall

Connect the f to the supply mains

·Mounting on DIN-rails

used terminal block

Use a 3-wire copper cable with wire cross-section 1.5 mm . Before making any connections, make sure that the supply

mains power is off.

www. VIZIT-MB1PE Operating Instruction (revision )vizit-group.com 3 6/201 -605

Figure 5 - Mounting the Box on DIN-rails

Fix the Box to the lower DIN-rail with a

self-tapping screw . DIN 7504M (not

supplied)

3 5х19

Hook the lugs over the top DIN-rail.

240

Figure 4 – Mounting the Box on a wall

150

170

Drill three holes

(1) in the wall with diameter 6 mm

and depth 4 mm

- Drive anchors (2) into the holes, and

fasten screws in the anchors.

Leave some distance between the

screw heads and wall (around 3 mm).

Anchors and screws are supplied.

Make necessary measurements and

put marks on a wall.

(3)

Hook the brackets (13) (see Fig.1)

over the screws (3) to hang the Box

on the wall.

- Fasten a screw (4).

L PE

FUSED TERMINAL BLOCK

MAINS SOCKET OUTLET

To the supply mains of a building

F 1.6AL V250

Figure 6 Wiring diagram of the Box connection to the supply mains–

Wiring order

Split the cable wires. Cut the live and neutral to the appropriate size, leaving the PE conductor (green / yellow) a bit longer.

Strip the leads. Strip length: 7 - 8 mm.

Connect the live (L), neutral (N) and PE conductors to the fused terminal block (see Fig. 7).

2 9х1

-(1

Fix doorphone units inside the Box

Make connections of doorphone units

Check doorphone units for proper operation

Padlock the door

Note.

Use screws . 3 (supplied) and holes in the back of the Box to fix doorphone units. Terminals of a control unit and power

supply units shall be oriented horizontally to ensure most efficient ventilation of the units.

The Box is capable to house the following units and combinations of units:

- one control unit / power supply unit and one commutator distribution amplifier; or

- one control unit and one power supply unit.

The correct location of units inside the Box is given on Figures 8 - 10

Let doorphone cables in through the doorphone cable inlets (6) see Fig. ), and connect the cable conductors to

corresponding terminals of doorphone units

If the doorstation design provides protective earthing, connect the PE conductor of the doorstation to the terminal (10), and

clamp the connection.

Plug the control unit’s / power supply unit’s mains plug in the Box socket outlet.

Switch the mains power on .

Switch the control unit’s power on and check doorphone units for operation following their operating instructions.

The Box is provided with a special padlock lug. Use a padlock to lock the Box.

Apadlock is not supplied.

Let the supply mains cable through the cable gland

Fix the mains cable with the sealing nut of the cable gland

www. VIZIT-MB1PE Operating Instruction (revision )vizit-group.com 4 6/201 -605

Protective earthing conductor (green / yellow)

Neutral (blue)

Live (black or brown)

conductor

Figure 7 – Mains connection to the fused terminal blockconductors

www. VIZIT-MB1PE Operating Instruction (revision )vizit-group.com 5 6/201 -605

Figure 9 - Control unit and one commutator / distribution amplifier layout

Figure 8 - Power supply unit and one commutator / distribution amplifier layout

www. VIZIT-MB1PE Operating Instruction (revision )vizit-group.com 6 6/201 -605

Figure 10 - Control unit and power supply unit layout

Power

Supply

Unit

Control

Unit

Adapter plug

with 2 sockets

ViziT VIZIT-MB1PE Operating instructions

ViziT VIZIT-MB1PE Operating instructions

ViziT VIZIT-MB1PE Operating instructions

Related papers

Other documents