ViziT RD-4F Operating instructions

ViziT
Brand
ViziT
Model
RD-4F
Type
Operating instructions

ViziT RD-4F is a reader intended for operation within RF controllers VIZIT-KTM600F and VIZIT-KTM602F. It can be mounted on a wall or on a fixed door leaf. The reader has an LED indicator and a built-in antenna. It is powered by a 12-27 VDC power supply and consumes 0.5 W of power. The operating temperature range is - 30°C to +50°C, and the relative humidity of air is up to 98% at 25°C.

The ViziT RD-4F reader can be used to control access to a building or room. It can be used with a variety of different access control cards or tags. The reader can also be used to trigger an alarm or other event when a valid access card or tag is presented.

ViziT RD-4F is a reader intended for operation within RF controllers VIZIT-KTM600F and VIZIT-KTM602F. It can be mounted on a wall or on a fixed door leaf. The reader has an LED indicator and a built-in antenna. It is powered by a 12-27 VDC power supply and consumes 0.5 W of power. The operating temperature range is - 30°C to +50°C, and the relative humidity of air is up to 98% at 25°C.

The ViziT RD-4F reader can be used to control access to a building or room. It can be used with a variety of different access control cards or tags. The reader can also be used to trigger an alarm or other event when a valid access card or tag is presented.

RD-4F
RD 4F VIZIT-KTM60 F
VIZIT-KTM602F
SPECIFICATIONS
VDC
.W
47 75 mm
.kg
OPERATING CONDITIONS
+50
PARTS LIST
VDC
OPERATING INSTRUCTION
- 0
12...27
0 5
хх
0 1
°C
98% 25°C
SAFETY INSTRUCTIONS
Reader (the Reader hereinafter) is intended for operation within RF controllers ,
Operating voltage
Power consumption
Dimensions (W)x(H)x(D)
Weight
Ambient temperature range to
Relative humidity of air up to at
The product does not contain voltage above
Do not make any connections or repair when the power is on
Take care not to spill any liquids or chemically active substances on the product. Switch the power off before cleaning the
product. Clean by wiping with dry soft cloth. Do not use any liquid cleaners, aerosol cleaners or abrasive agents
.
.
.
.
.
18
°C
2
- 30
8
www. 201 - /2vizit-group.com RD-4F Operating Instruction (revision 6 11) 1
Figure 2 Destination of wires-
Operating Instruction
x1
Fasteners
Screw 404х Anchor 46х 0
x2 x2
Gag
x 4
Reader RD 4F-
x1
2
Figure Reader RD-4F appearance1 -
1LED indicator
Reader’s antenna
1
2
Destination
Wire colour
Supply voltage for RD-4FRed
GroundBlack
DataWhite
Supply voltage for Reader’s
buzzer
Blue
INSTALLATION
For qualified installation, wiring and servicing refer to technical and commercial partners of VIZIT TM.
The list of companies is given on VIZIT.EU ( .http://vizit.eu/eurounion/)
The Reader is mounted either on a wall, or on a fixed door leaf.
Wiring diagrams and operating order of the Reader RD-4F is given in operating instructions on the
RF controllers VIZIT.
3
4
- Drill 2 holes (1)
with diameter 3 mm
- Drill a hole for wires (2) with diameter
no less than 5 mm
Attach the Reader to the and
fasten two screws x13 ( ) .
- Drive in gags .
.
.
-
3
(4)
fixed door leaf
()not supplied3.5
Figure 4 - Front side mounting on a fixed door leaf
2
1
1
Figure 5 - Back side mounting on a fixed door leaf
- Drill 2 holes (1)
with diameter 5.5 mm
- Drill a hole for wires (2)
with diameter 5 mm
Attach the Reader RD-4F to the
and fasten two screws ( ) .
on
.
- Drive in gags .
.
.
-
М5 3
The screw length is chosen the condition:
door leaf thickness plus 5 mm
(4)
fixed door leaf
()not supplied
1
1
3
4
2
49 mm
- Drill 2 holes (1) in the wall
Diameter is 6 mm, and
depth is 40 mm.
- Drive anchors (2) into the holes
- Drill a hole for wires ( ) with diameter 5 mm
.
.
3.
-
х0 ()
()
Attach the Reader to the wall and
fasten two screws 4 4 4 in the anchors.
- Drive in gags 5 .
Figure 3 Mounting on a wall-
4
5
60 mm
3
1
2
www. 201 - /2vizit-group.com RD-4F Operating Instruction (revision 6 11) 2
  • Page 1 1
  • Page 2 2

ViziT RD-4F Operating instructions

ViziT
Brand
ViziT
Model
RD-4F
Type
Operating instructions

ViziT RD-4F is a reader intended for operation within RF controllers VIZIT-KTM600F and VIZIT-KTM602F. It can be mounted on a wall or on a fixed door leaf. The reader has an LED indicator and a built-in antenna. It is powered by a 12-27 VDC power supply and consumes 0.5 W of power. The operating temperature range is - 30°C to +50°C, and the relative humidity of air is up to 98% at 25°C.

The ViziT RD-4F reader can be used to control access to a building or room. It can be used with a variety of different access control cards or tags. The reader can also be used to trigger an alarm or other event when a valid access card or tag is presented.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents