ViziT VIZIT-MB2P Operating instructions

Brand: ViziT

Model: VIZIT-MB2P

Type: Operating instructions

Mounting Box 2PVIZIT-MB

Mounting Box (the Box hereinafter) is intended for use as a housing for trademarked doorphone /

video doorphone units.

The Box has a socket outlet installed to provide connection of the control unit / power supply unit to the supply mains of

the premises.

The Box is capable to house the following combinations of units:

- one control unit / power supply unit ; or

- one control unit /power supply unit and one power supply unit w v EU FARADAY; * or

- two commutators distribution amplifiers ; or

- two commutators distribution amplifiers and one power supply unit w v EU FARADAY;

- two power supply units w v EU FARADAY. *

If installing in the Box two units which require mains supply, use an adapter plug with two Euro sockets, e.g.

BRENNENSTUHL 1508030 (the adapter plug is not supplied). Appearance of the adapter plug with two sockets is given on

Figure 2.

VIZIT-MB2P VIZIT

VIZIT

Note

19 /14.4 /

/ 19 /14.4 /

19 /14.4 /

Figure Mounting Box VIZIT-MB2P appearance and mounting dimensions1 -

Case

Protective earthing terminal to

connect the

protective earthing wire

Doorphone communication

cables inlet

Protective bonding terminal to

connect the door to the case

Door

Earthing terminal for the

doorstation

Lugs to hook the box on a DIN-

rail inside a wiring closet

Padlock lug

mains cable’s

Mains socket outlet

Cable tie

Mains cable inlet

Seal for cable inlet

Brackets to fix on a wall

150

130

12 12

Figure Adapter plug with two Euro sockets2 -

SPECIFICATIONS

OPERATING CONDITIONS

PARTS LIST

MB P

SAFETY INSTRUCTIONS

INSTALLATION

Ambient temperature range + to +

Relative humidity of air up to at

Mounting Box pc.

Fastening kit pc.

Operating Instruction pc.

1°C 4 °C

93% 25°C

VIZIT- 2 1

Rated mains voltage

Rated mains frequency

Maximum power consumption of

units installed in the Box

Ingress protection rating

Class

Dimensions (W)x(H)x(D) x x

Weight

When the mains power is on, the Box contains dangerous for life mains voltage - .

To avoid electric shock the Box shall be connected to the protective earth using the mains cable protective earthing wire.

In order to protect the mains socket outlet in the Box and the mains cable against current overload, the premises must

have a single-pole or double-pole circuit breaker (with rated current from 3A to 6A) installed in the power system. A single-

pole circuit breaker

Wiring and servicing of the Box shall be referred to qualified personnel.

When connecting the Box to the supply mains, mains power must be off.

Before performing any wiring or repair inside the Box, make sure that the control unit’s / power supply unit’s plug is

disconnected from the mains socket outlet.

The Box shall not be exposed to dripping or splashing and no objects filled with liquids shall be placed on the Box.

No metallic objects shall penetrate into ventilation openings of the Box.

The Box shall be installed in heated premises with proper ventilation. The Box may be installed either on a wall, or on a

DIN-rail inside a wiring closet.

The mounting dimensions of the Box are given on Fig.

Follow the directions on Fig.

VAC

.kg

WARNING! 230 V

WARNING! Do not mount the Box near heating equipment!

Mounting on a wall

Mounting on a DIN-rail

VIZIT

Make necessary measurements and put marks on a wall. Drill holes and drive in anchors 6х30 and screws 4х35 supplied.

Hook the brackets (see Fig.1) over the screws to hang the Box on the wall.

100

IP20

251 208 93

1 3

230

shall be connected to a phase wire.

Figure 3 - Mounting the Box on DIN-rails

Fix the Box to the lower DIN-rail with a

self-tapping screw . DIN 7504M (not

supplied)

3 5х19

Hook the lugs over the top DIN-rail.

2 9х13

19 /14.4 /

/ 19 /14.4 /

19 /14.4 /

4-11.

- ( 1) .

Connect the socket outlet to the supply mains.

Wiring order

Fix doorphone units inside the Box

VIZIT

Make connections of doorphone units

Check doorphone units for proper operation.

Padlock the door

Note.

Use a 3-wire copper cable with wire cross-section no less than 0.75 mm . Before making any connections, make sure that

the supply mains power is off.

Let in the supply mains cable through the sealed mains cable inlet , .

Split the cable wires. Cut the live and neutral to the appropriate size, leaving the protective earthing wire (green / yellow) a

bit longer.

Strip the leads

Remove the cover from the socket outlet and connect the live and neutral to the socket outlet’s terminals. Restore the

cover back to its place.

Connect the protective earthing wire to the protective earthing terminal . To ensure proper connection, the wire and the

ring terminal should be clamped together with a clipper.

Fix the supply mains cable inside the Box with a cable tie

Use screws . (supplied) and holes in the back of the Box to fix doorphone units. Terminals of a control unit and power

supply units should be oriented horizontally to ensure most efficient ventilation of the units.

The Box is capable to house the following units and combinations of units:

- one control unit / power supply unit ;

- one control unit / power supply unit and one power supply unit w v EU FARADAY;

- two commutators distribution amplifiers ;

- two commutators distribution amplifiers and one power supply unit w v EU FARADAY;

- two power supply units w v EU FARADAY.

The correct location of units inside the Box is given on Figures

Let doorphone cables in through the doorphone cable inlets see Fig.

If the doorstation design provides for its earthing, connect the protective earthing wire of the doorstation to the doorstation

earthing terminal , and clamp the connection.

Plug the control unit’s / power supply unit’s mains plug in the Box socket outlet (see Fig. 4, 5).

Plug the control unit and power supply unit’s mains plugs in an adapter plug with two Euro sockets (see Fig. 6, 7, 11).

Switch the mains power on .

Switch the control unit’s power on and check doorphone units for operation following their operating instructions.

The Box is provided with a special padlock lug. Use a padlock to lock the Box.

Apadlock is not supplied.

Figure Position of control unit in the Box4 - VIZIT

Figure Position of power supply unit in the Box5 - VIZIT

Figure Position of control unit

in the Box

6 -

19 /14.4 /

VIZIT and power supply

unit w v EU FARADAY

Figure Position of power supply unit7 -

19 /14.4 /

VIZIT and power

supply unit w v EU FARADAY in the Box

Figure 8 - Position of two commutators and distribution

amplifiers in the BoxVIZIT

Adapter plug

with 2 sockets

Adapter plug

with 2 sockets

Figure Position of two commutators / distribution

amplifiers

in the Box

9 -

19 /14.4 /

VIZIT and one power supply unit

w v EU FARADAY

Figure Position of one commutator / distribution

amplifier

10 -

in the Box19 /14.4 /

VIZIT and one power supply unit

w v EU FARADAY

Figure 11 - Position of two power supply units

19 /14.4 /w v EU FARADAY in the Box

Adapter plug

with 2 sockets

ViziT VIZIT-MB2P Operating instructions

ViziT VIZIT-MB2P Operating instructions

ViziT VIZIT-MB2P Operating instructions

Related papers

Other documents