English
EN
SETUP AND USER MANUAL
XNVR3216H - XNVR3316H - XNVR3332H
XNVR3204PH - XNVR3208PH
NETWORK VIDEO RECORDER
FA00745-EN
AUDIO
OUT
AUDIO
IN VGA USB LAN DC 48V
DC 12V
ALARM IN
ALARM OUT
2
1
4
3
PoE PORTS
AUDIO
OUT
AUDIO
IN
USB 3.0 LAN
AUDIO
OUT
AUDIO
IN VGA USB LAN DC 48V
PoE PORTS
2 6
5
1
4 8
7
3
DC 12V
AUDIO
OUT
AUDIO
IN
VGA USB 3.0LAN
Page 2 - Manual: FA00745-EN - ver. 1 - 04/2017 - © CAME S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.
Description of parts
Rear panel XNVR3316H - XNVR3332H
GENERAL PRECAUTIONS
• Important safety instructions: READ CAREFULLY
• Installation, programming, commissioning and maintenance must only be carried out by qualified, expert sta and in full compliance with the
applicable law.
• Always cut o the mains power when doing cleaning and maintenance jobs.
• This product must only be used for the purpose for which it was designed.
• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.
DESCRIPTION
Digital network video recorder with 4, 8, 16 inputs.
Technical data
Type XNVR3204PH XNVR3208PH XNVR3216H XNVR3316H XNVR3332H
IP video inputs (number of channels) 4 8 16 16 32
IP audio inputs (number of channels) 4 8 16 16 32
HDMI video outputs
4K x 2K / 1920x1080 / 1280x1024 1 1 1 1 1
VGA video outputs, 1920x1080 / 1280x1024 (BNC) 1 1 - 1 1
Audio inputs/outputs (RCA) 1/1 1/1 1/1 1/1 1/1
Video compression of recording H.265 / H.264 H.265 / H.264 H.265 / H.264 H.265 / H.264 H.265 / H.264
Recording resolutions supported 5MP / 4MP / 3MP / 1080P / 960P / 720P
Recording frame rate @ 5MP (fps) 1 - 25 1 - 25 1 - 25 1 - 25 1 - 25
SATA ports available 1 1 1 2 2
RJ45 Ethernet ports 1x
10/100 M
1x
10/100 M
1x
10/100 M
1x
10/100/1000 M
1x
10/100/1000 M
USB 2.0 ports 2 2 2 1 1
USB 3.0 ports - - - 1 1
Alarm inputs - - 4 - -
Alarm outputs - - 1 - -
Power supply (V DC) 48 48 12 12 12
Consumption without hard disk (W) ≤ 5 ≤ 5 ≤ 5 ≤ 5 ≤ 15
Operating temperature (°C) -10 to +50 -10 to +50 -10 to +50 -10 to +50 -10 to +50
Operating humidity (%) 10 to 90 10 to 90 10 to 90 10 to 90 10 to 90
Dimensions (mm) 300 x 248 x 52 300 x 248 x 52 300 x 248 x 52 380 x 268 x 52 430 x 300 x 55
❶❷ ❸ ❹ ❺
❻
AUDIO
OUT
AUDIO
IN VGA USB LAN DC 48V
DC 12V
ALARM IN
ALARM OUT
2
1
4
3
PoE PORTS
AUDIO
OUT
AUDIO
IN
USB 3.0 LAN
AUDIO
OUT
AUDIO
IN VGA USB LAN DC 48V
PoE PORTS
2 6
5
1
4 8
7
3
DC 12V
AUDIO
OUT
AUDIO
IN
VGA USB 3.0LAN
AUDIO
OUT
AUDIO
IN VGA USB LAN DC 48V
DC 12V
ALARM IN
ALARM OUT
2
1
4
3
PoE PORTS
AUDIO
OUT
AUDIO
IN
USB 3.0 LAN
AUDIO
OUT
AUDIO
IN VGA USB LAN DC 48V
PoE PORTS
2 6
5
1
4 8
7
3
DC 12V
AUDIO
OUT
AUDIO
IN
VGA USB 3.0LAN
AUDIO
OUT
AUDIO
IN VGA USB LAN DC 48V
DC 12V
ALARM IN
ALARM OUT
2
1
4
3
PoE PORTS
AUDIO
OUT
AUDIO
IN
USB 3.0 LAN
AUDIO
OUT
AUDIO
IN VGA USB LAN DC 48V
PoE PORTS
2 6
5
1
4 8
7
3
DC 12V
AUDIO
OUT
AUDIO
IN
VGA USB 3.0LAN
Page 3 - Manual: FA00745-EN - ver. 1 - 04/2017 - © CAME S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.
USE OF DEVICE
Switching NVR on and o
Switching on the device
Connect the monitor and power supply; the blue LED on the front comes on and the device carries out startup.
A guided procedure lets you set up the device.
Switching o the device
On the main menu select the "Shutdown" icon; this opens a Shutdown window; press the "OK" button and then disconnect the power supply.
❻ USB 2.0 port,
❼ Audio inputs / outputs,
❸ Alarm inputs and outputs,
❾ PoE ports.
Rear panel XNVR3208PH
Rear panel XNVR3204PH
Rear panel XNVR3216H
❶ Power input from power supply,
❽ LAN port,
❻ VGA video output,
❹ HDMI video output,
❺ USB 3.0 port,
❶
❶
❶
❼
❽
❼ ❾
❾❼
❺
❻
❻
❹
❸ ❹
❸ ❹
❷
❷
❷
Page 4 - Manual: FA00745-EN - ver. 1 - 04/2017 - © CAME S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.
QR Code
Enabling the NAT box.
If you want to access the device via your iOS or Android smartphones download the Superlive PLUS app; for iOS or Android tablets download the
Superlive PLUS or Superlive HD app.
After installing and launching the app, scan the QR Code that appears on the screen for immediate access to the video recorder.
Entering network parameters
❶ Tick this box for the system to automatically assign an IP
address to the device.
If box ❶ is not ticked the following data must be entered
manually:
- IP ADDRESS
- SUBNET MASK
- GATEWAY
- PREFERRED DNS SERVER
- ALTERNATE DNS SERVER: this selection allows the NVR to
be used/displayed remotely.
The pre-set values for the ports are:
HTTP port: 80 SERVER port: 6036
Press the NEXT button to continue with setup.
Setting up correct date and time.
Press the NEXT button to continue with setup.
When starting up the device for the first time, it is possible to choose a
personalised password that can be changed later.
When you click on the fields that require text or numbers to be entered, a keypad
is displayed; select the letters and/or numbers required to compose the text; use
the SHIFT key to enter capital letters and symbols.
Press the NEXT button to continue with setup.
Setting up the device's main parameters via the WIZARD window
Basic parameters
Switch on the NVR.
The WIZARD (GUIDED SETUP) window lets you quickly carry out the main
operations to make the device operational.
Press the SKIP button to immediately exit the guided setup; press the central
button to start the guided setup.
Note: The data entered during the guided setup (Wizard) can be changed at any
time.
❶
Page 5 - Manual: FA00745-EN - ver. 1 - 04/2017 - © CAME S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.
Adding video cameras
Pressing button ❷ updates the list of IP video cameras there
are in the same local network as the NVR.
Press button to add the video camera you want.
Select ❸ to add all the video cameras in the list.
Press button to delete one of the video cameras added to
the list. Press button ❹ to delete all of the video cameras
added to the list.
If the IP video camera you want does not have an IP address
that is in the same network segment as the NVR, select the
device and press the icon ❺ to change the IP address
❻; select the video camera with the new address and press
the button to add it to the list.
By pressing the icon ❼ you can associate a name to the
IP video camera so as to make it easier to recognise.
The video cameras connected directly to the NVR's PoE ports
are addressed and managed automatically.
Press the NEXT button to continue with setup.
For MANUAL mode the alarm input that triggers the recording, the "motion" alarm that triggers the recording, and the programmer timer must be
set for each video camera.
To set up the recording options more precisely, press the icon ⇨ Settings ⇨ Record.
Press the OK button to save the settings.
Recording settings
Two recording modes are available: AUTOMATIC and
MANUAL.
Choose one of the options available for AUTOMATIC mode:
❾ Recording is activated if the video camera detects motion
within a pre-set area of the image.
❿ Recording is activated following the activation of an
alarm input.
⓫ Recording is activated when the conditions described in
points ❾ and ❿ occur.
⓬ Recording always on; if the video camera detects motion
within a pre-set area of the image an alarm is triggered.
⓭ Recording always on; if an alarm input is activated an
alarm is triggered.
⓮ Recording always on; if an alarm input is activated or if
the video camera detects motion within a pre-set area of the
image an alarm is triggered.
Press the OK button to save the settings.
❷ ❸ ❹
❺
❻
❼
❽
❾
❿
⓫
⓬
⓭
⓮
Page 6 - Manual: FA00745-EN - ver. 1 - 04/2017 - © CAME S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.
After ActiveX is installed, the login window opens:
Serial No: MAC address of NVR
To display the MAC address of the NVR, access Menu ⇨ Settings ⇨ Network ⇨ Network status.
Alternatively select the icon on the lower tool bar.
User Name: name of user of the NVR (default name is admin).
Password: NVR password (password chosen on first startup via the guided setup; the default
password is 123456).
Remote access can also take place via NVMS1000 software (for PC) or NVMS1200 software (for
MAC OS).
CONNECTION VIA CLOUD
NAT settings
The NVR must be powered and connected to the network.
1. Access the Menu ⇨ Settings ⇨ Network ⇨ NAT.
Select the NAT tab.
2. Enable NAT and if necessary fill in the NAT Server fields, the default NAT Server value is www.autonat.com.
3. Click APPLY to save the parameters.
Access to NAT server
After completing the NAT settings, it is possible to access the NAT server from the PC (enter http://www.autonat.com in the browser).
If you are accessing NAT for the first time, the ActiveX plugin is automatically downloaded.
Access the playback and recorded material search
window by pressing icon on the bottom of the
screen or by selecting PLAYBACK from the menu .
Video cameras can be added manually to the playback
window.
Select the icon to make the window appear that lets
you add a video camera to the views.
Select the video camera you want and then click ADD to
add video cameras to the views.
The files of recordings from the video camera added will
be played back within the interface.
General playback
By right-clicking with the mouse on the screen that shows the images taken live by
the video camera you can choose the section of video recorded that you want to see
immediately from the menu that appears.
The same menu can be called up by pressing icon that is next to icon on the
bottom of the screen that shows the images taken live by the video camera.
PLAYBACK
Fast playback
Page 7 - Manual: FA00745-EN - ver. 1 - 04/2017 - © CAME S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.
Enter a name of your choice in the box ❹ to identify the device. Enter the credentials for access to the video recorder into boxes ❺ and press
button ❻.
If you are using a connection via DDNS
Type the Host name followed by the domain inside the box ❶ (for example: came.autoddns.com).
If you are using a connection via Cloud
Touch the icon ❷ and scan the QR code that you can find in the NVR's information menu under the heading QR code. Alternatively you can type
the code directly into the Device box ❸.
CONTROL FROM A MOBILE DEVICE
Access via app
For iOS or Android smartphones download the Superlive PLUS app; for iOS or Android tablets download the Superlive PLUS or Superlive HD
app. Once the app has started, follow the sequence shown in the images below.
❶❸
❹
❻
❺
❷
www. came.com
CAME S.p.A.
Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c
31030 Dosson di Casier
Treviso - Italy
33079 Sesto al Reghena
Pordenone - Italy
(+39) 0422 4940
(+39) 0422 4941
(+39) 0434 698111
(+39) 0434 698434
English - Manual: FA00745-EN - ver. 1 - 04/2017 - © CAME S.p.A.
The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.
The device just added is shown in the list; the green icon ❼ indicates that the connection to the video recorder is on.
Go back to the previous screen to display and select the devices connected. The icon ❽ lets you open the window through which to choose the
display mode.
❽
❼
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Elvox 46540.H08 Quick Manual
-
Novus NVR-6204P4-H1 User manual
-
-
-
-
Genie WONVR18P5 User guide
-
Novus NVR-6308P8-H1-II User manual
-
-
-