CAME MSC Installation guide

FA00187-EN

Engl

i

s

h

E

N

IP VIDEO CAMERAS FOR VIDEO SURVEILLANCE

QUICK INSTALLATION GUIDE

Page 2 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

General warnings

• Do not expose the product to rain or moisture.

• Check that the device is securely attached to the wall or ceiling on which it is installed.

• Before using the camera, check that the supply voltage is correct.

• Do not attempt to disassemble or modify the camera.

System requirements

• Operating system: Windows XP/7/Vista/Server 2000/Server 2008 (use IE as the browser).

• CPU: 1.66 GHz or more.

• Memory: 1 GB or more.

• Graphics memory: 128 MB or more.

• Internet protocol: TCP/IP (IPv4).

Page 3 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

General presentation

This guide provides the basic instructions for installing the the network camera and explains how to access

it. For more details, consult the user manual.

Mini-dome network video camera

Release tab

Lens

Error LED

Power supply LED

Micro-SD/SDHC card slot

Reset

Ethernet port (PoE)

*N.B.

1) Error LED: the error LED lights up when the camera is turned on or in the event of an error.

2) Reset button: pressing the reset button for 5 seconds will restore the factory settings.

Page 4 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Mini-dome IR network video camera

Release tab

Ethernet port (PoE)

Lens

Error LED

Power supply LED

Micro-SD/SDHC

card slot

Reset

Brightness

sensor

IR LED

Page 5 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Mini-dome IR anti-vandalism network video camera

Ethernet port (PoE)

Reset

Power supply and system

LED

Lens

Camera locking screw

Brightness sensor

IR LED

Microphone

Micro-SD/SDHC

card slot

Page 6 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Mini-cube network video camera

Ethernet port

WPS/Reset

button

Power supply

connector

Micro-SD card slot

SIP button

I/O alarm

connector

Lens

Brightness sensor

Loudspeaker

PIR sensor

Indicator LEDs

IR LED

Microphone

*N.B.

1) SIP button: alarm activation via SIP call. After pressing this button, the camera will call the SIP phone.

2) WPS button: press this button ﬁ rst and then the WPS button on the router to automatically conﬁ gure the

wireless connection.

Page 7 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Mini-bullet network video camera

Ethernet port

Micro-SD/SDHC

card slot

Reset

button

Lens

Brightness sensor

IR LED

Page 8 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Pro-bullet network camera

Power supply

connector

Alarm/Audio

connector

Micro-SD/SDHC

card slot

Reset

button

CVBS video

output

Lens

Ventilation holes

IR LED

Ethernet port (PoE)

Page 9 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Pro-dome network camera

Micro-SD/SDHC

card slot

Reset

button

Lens

IR LED

Microphone

Brightness sensor

Page 10 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Installing the cameras

Mini-dome network video camera

1. Remove the cover of the Dome.

2. Tighten the screws.

Release tab

Page 11 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

3. Run an Ethernet cable through the ceiling or wall and connect it.

4. Adjust the lens angle and focus.

5. Secure the cover of the Dome.

Pan range: +15°

Tilt range: 0-90°

Page 12 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Mini-dome IR network video camera

1. Remove the cover of the Dome.

2. Tighten the screws.

Release tab

Page 13 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

3. Run an Ethernet cable through the ceiling or wall and connect it.

4. Adjust the lens angle and focus.

5. Secure the cover of the Dome.

Pan range: +15°

Tilt range: 0-90°

Page 14 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Mini-dome anti-vandalism network video camera

1. Remove the cover of the Dome.

Page 15 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

2. Tighten the screws.

3. Run an Ethernet cable through the ceiling or wall and connect it.

Page 16 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

4. Loosen the screw and adjust the lens angle and focus.

5. Secure the cover of the Dome.

Page 17 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Mini-cube network video camera

1. Install the “cube” camera on the ceiling/wall or place it horizontally.

Page 18 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

2. Connect the power adapter and Ethernet cable.

3. Set the frame.

Ethernet cable

Power cord

Page 19 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

Mini-bullet network video camera

1. Remove the waterproof connector and corresponding rubber seal.

2. Open the back cover.

3. Insert a micro-SD/SDHC card, connect an Ethernet cable by passing it through the rubber seal and place

the desiccant bag supplied inside the camera (this need to be replaced every time you open the back cover).

4. Replace and tighten the back cover.

5. Tighten the rubber seal, the terminal and the waterproof connector nut.

Page 20 - Manual code FA00187-EN - ver. 1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.

6. Pass the Ethernet cable through the centre of the mounting bracket, attach the bracket to the camera, turn

it and secure it using the screws.

7. Install the camera on the ceiling or wall.

Page is loading ...

CAME MSC Installation guide

CAME MSC Installation guide

Related papers

Other documents