2. CAME
  3. MS-N1009-UT

CAME MS-N1009-UT Installation guide

  • Hello! I'm here to help you understand your CAME Network Video Recorder MS-N1000 series MS-N1009-UT. I've reviewed the setup and user manual and can assist you with questions about its features, recording options, camera setup, and more. This document includes vital information such as default credentials, recording settings, and network configuration. Feel free to ask me anything!
  • What is the default user name and password?
    What recording resolutions are supported?
    How do I add IP cameras to the device?
    Where can I back up my recording files?
MS-N1009-UT
FB00085-ENFA00425-EN
SETUP AND USE MANUAL
NETWORK VIDEO RECORDER
English
EN
Page 3 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 2 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
INSTALLATION NOTES
Before using the network video recorder, take note of the following:
• Keep liquids away from the video recorder.
• Place the video recorder in a well-ventilated area.
• Make sure that the humidity and temperature values in the room are within the limits
allowed by the video recorder.
• Humidity and an accumulation of dust on the video recorder's control board may cause a
short circuit. Dust the control board, connector, casing and fan regularly with a suitable
brush.
• Replacing the battery incorrectly may lead to a risk of explosion. The battery should never
be replaced by users and the replacement battery must be the same or of an equivalent
type.
☞ The appliances covered in this manual are MS-N1000 video recorders.
Main product features
Basic information
• The range of Milesight video recorders - including the MS-N1000 series - can be
connected to all IP cameras that support the ONVIF protocol.
Monitoring
• HDMI video output, separate real-time display and playback features.
• Compatibility with HDMI UHD display with a maximum resolution of 3840x2160 (UT series
NVRs only).
• 1/4/8/9/16 real-time display images, with adjustable channel sequence.
• Quick menu for viewing in real time.
• Real-time group sequencing, manual recall and automatic sequencing with adjustable
interval.
• Motion detection and video signal loss warning.
• Support for various PTZ protocols, PTZ presets and automatic sequences.
• Enlarging of the central area of the image using the mouse on any area.
• Privacy mask.
• OSD title and date configuration.
HDD management
• S.M.A.R.T. technology support.
Page 3 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 2 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Recording/snapshot and playback
• Programming holidays.
• Recording mode with and without overwriting function.
• Support of dierent types of recording, including time slot, alarm, motion detection,
motion or alarm, motion and alarm etc.
• Support of 12 recording periods with separate recording types.
• Pre-recording and post-recording for motion or snapshot detection, alarm or snapshot
recording, motion and alarm recording, motion or alarm recording; manual and time slot
pre-recording.
• Support for local/snapshot recording.
• Digital zoom on desired areas during playback.
• Video data playback.
• Pause, fast play, slow play, skip forward and skip back features during playback, progress
bar manageable with the mouse.
• Manual snapshots.
Backup
• Backup to USB port.
• Backup in FAT32 format.
• Maintenance and management of backup devices.
Alarms and exceptions
• Video signal loss alarm.
• Motion detection and alarm configuration.
• Network disconnected/HDD full/recording failed/HDD error alarms.
• Several types of alarm signals (acoustic signal, sending e-mail, motion detection, relay
on/o).
Other features
• Multi-level user management - the administrator can create dierent users with dierent
access rights.
• Manual alarm activation and silencing.
• Import/export of configured information.
Network
• Unicast and multicast; TCP, UDP and RTP for unicast.
• Remote search, playback and download of video files; resume from the point of
interruption.
• Remote parameter acquisition and configuration; import and remote device parameter
import and export.
Page 5 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 4 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
• P2P remote access.
• Remote acquisition of device status, system log and alarm status.
• Remote controls.
• Remote system maintenance for hard disk formatting, upgrades, reboots etc.
• Upload of alarms and exceptions on the remote host.
• Start and stop recording remotely manually.
• Start and stop alarm output remotely manually.
• Remote acquisition of BMP images.
• PTZ remote control.
• Built-in web server.
Model MS-N1009-UT
Video/audio
input
Network video input 9
Max data stream 45 Mbps
Network audio input 9
Analogue audio input -
Video/audio
output
HDMI output 1
VGA output -
Audio output -
Synchronous preview
/
Synchronous playback
30 fps@D1 9
30 fps@720P 9
30 fps@1080P 4
20 fps@3MP 1
8 fps@5 MP 1
30 fps@2160P 1
Page 5 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 4 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Model MS-N1009-UT
Video/audio
compression
Video compression H.265(HEVC)/H.264
Recording resolution
3MP(UHD-2160P)/5M-
P/3MP/1080P/UX-
GA/720P/VGA/D1/CIF/
QCIF
Max synchronous recording 9*2160P
Memory
SATA 2 x 2.5" SATA HDD
4 TB max with 2 TB each
External memory -
Capacity Up to 2 TB each HDD
Interface
USB 2*USB 2.0
Alarm input/output -
Page 7 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 6 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
LOCAL OPERATIONS
Setup wizard
By default, the setup wizard starts immediately after turning on the video recorder. The setup
wizard helps you set certain essential values, guaranteeing correct device operation. You can
choose whether to enable the wizard when the device starts up.
For setup, proceed as follows:
HARDWARE
Operation of buttons and indicators
MS-N1000 series: MS-N1009-UT
Page 7 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 6 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Step 2. Setting the data and time
Select the time zone and the date format or enter the date and time manually.
Step 1. Enter your user name and password (default user name 'admin', password
'ms1234').
If you want to change the admin password, enter the new password.
Step 3. Network settings
Enter the IP address, subnet mask, gateway and preferred DNS server.
ⓐ
Page 9 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 8 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Step 4. Access
Enter your user name and password.
Video playback.
Playback can be based on the time recorded. Playback of recorded files in the specified time
period. Support of synchronous playback of various channels.
Step 1. Access the video playback interface shown in figure ⓐ following the path
Main menu → Playback .
Playback
Playback and backup of recorded files in the specified time period.
Page 9 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 8 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Select the channel and playback layout. Click on the date highlighted in red when there
are recorded files in the selected channels (the recording type and data will be displayed
as shown below) and click to start playback.
N.B.
1. The day highlighted in red contains recording files. Select this date to start playback.
2. You can select up to 16 channels to be played synchronously.
Description of the video playback toolbar
The toolbar can display multi-event recordings and show the type of event that occurred in a
given recording period. The symbolic meaning of each colour is explained below:
Blue --- Time slot Green --- Movement
Red --- Alarm Black --- Emergency
In the bar shown above, for example, it is clear that event occurred in the defined recording
period related to movement and the time slot.
Page 11 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 10 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Rewind
Stop
Playback
Pause
Skip back
Skip forward
Fast back
Fast forward
4 previous cameras
4 next cameras
Timeline back
Timeline forward
Expand timeline
Reduce timeline
Timeline
Playback position
Start timeline cut
End timeline cut
Audio On
Audio O
Snapshot
Backup
Video file backup
The recorded files can be stored on various devices such as USB flash drives, USB HDDs,
USB writers, CD/DVD and eSATA writers etc.
Step 1. Access the video playback interface by clicking Main.
Key
Page 11 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 10 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Step 2. Select the recorded files for backup
Select the channel and the date to backup, the start time on the timeline and click . The
icon changes to to signify the start of the cut.
Select the end time on the timeline and click . The icon changes to to signify the
end of the cut.
Step 3. Click to access the backup interface. Select the backup media and
click [Backup].
Step 4. The context window invites you to wait: please wait…
Step 5. Once you have exported all the backup files, the message 'Backup Success'
appears.
Page 13 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 12 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Camera settings
Before setup, make sure the IP device is connected to the same network as the video
recorder and that the video recorder network settings are correct.
Camera management
Step 1. Access the camera management interface following the path Main menu → Camera
→ Camera Management.
Step 2. Add the IP channel
Method 1. Add the IP channel in the camera search interface
1. Access the camera search interface following the path Main menu → Camera → Camera
Search.
2. Click [Search] to quickly search for IP devices that support ONVIF on the same network
segment as the video recorder.
Page 13 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 12 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
3. Double-click on the channel, enter your password and click [Add].
Or select a group of IP cameras with the same password.
Page 15 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 14 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Method 2. Add the IP channel in the camera management interface
1. Access the camera management menu following the path Main menu → Camera →
Camera Management.
2. Access the 'IP Channel' attributes page and select an inactive channel, filling in all the
data. Then click [Add].
There are three ways to add a camera:
1. ONVIF: if you select this protocol, you can add any ONVIF-compatible IP camera. The
formats in detail are shown in figure Ⓑ;
2. RTSP: you can add any IP camera that uses the RTSP protocol for managing video
streams.
You must select 554 for the port and enter the "resource path" for the camera. For the
Milesight device, for example, the main stream of the resource path is "/main" and the
secondary stream is "/sub".
Details regarding adding formats are shown in figure ⓒ;
3. MILESIGHT: if the IP camera is a Milesight device, you can select this protocol to add
the cameras. The formats in detail are shown in figure ⓓ.
Page 15 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 14 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
ⓑ
ⓒ
ⓓ
Page 17 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 16 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Step 3. Check the connection status
After adding the IP channels, click [Refresh]; the [status] will be displayed as [connected].
Otherwise, you need to check whether the network is connected or if the user name and
password are correct.
Step 4. Configure the IP channel
1. After you have added the channel, click or double-click the channel to re-enter the
information regarding the channel, address and password etc.
N.B.
By default, the user name and password are the default ones, the management port is 80
and the transport protocol is UDP.
1. Select the attributes page [Parameters] to regain access to the parameters of this channel.
Click [Save] to save the configuration.
Page 17 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 16 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
2. This IP channel can be deleted by clicking but you can also select several devices and
then click to delete them.
Camera search
Here you can search and add IP cameras.
Step 1. Access the camera search interface following the path Main menu →
Camera → Camera Search.
Page 19 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 18 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Step 2. Click [Search] to quickly search the IP devices that support ONVIF.
N.B.
The IP devices that appear on the list are those that support the ONVIF protocol on the same
network segment as the video recorder.
Step 3. Add the IP camera
Double-click on the channel, enter your password and click [Add].
Page 19 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 18 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Or select a group of IP cameras with the same password. Click [OK] to finish adding the
group.
Recording settings
Preparing the configuration
Step 1. Make sure the VCR has installed and initialised the HDD.
Access the disk management interface following the path System Settings → Disk
Management.
Page 21 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Page 20 - Manual code FA00425-EN - ver. 1 - 04/2016 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Step 2. Check that the HDD has enough space.
Access the disk management interface following the path System Settings → Disk
Management. Set [Recycle Mode] to ON in the event of insucient HDD capacity.
Recording mode
Step 1. Access the recording mode menu following the path Main menu → Record
→ Record Mode.
There are three recording modes: No Record/Always Record/Record by Schedule. You can
select whichever one you want for each channel.
[No Record]: if you choose this column, the video recorder will not record;
[Always Record]: the recorder will always record the channel you choose;
[Record By Schedule]: if you want the video recorder to record by schedule, select this
column and go to "Setting the recording program".
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/