CAME PS ONE Installation guide

Brand: CAME

Model: PS ONE

Type: Installation guide

INSTALLATION MANUAL

PSM101D

FA00593-EN

PARKING

CONTROL SYSTEM

lish

57 ÷ 82

< Ø 100

Ø 15

0,06 ÷ 0,1

58 - 80

Page

2 - Manual

FA00593-EN

FA00593-EN - ver.

1 - 02/2017 - © Came S.p.A. - The contents of this manual are subject to change at any time without prior notice.

KEY

This symbol indicates parts about safety.

This symbol tells you what to say to the end users.

MEASUREMENTS, UNLESS OTHERWISE INDICATED, ARE IN MILLIMETRES.

DESCRIPTION

Manned pay station with TCP/IP interface for parking systems. It consists of a PC with TFT LCD 9.7" touchscreen

display, VFD display (2 lines of 20 characters h. 9.66 mm) customer side and built-in thermal printer for tickets/

receipts (not for tax purposes).

Technical data

Type PSM101A

Mains power supply (V - 50/60 Hz) 120/230 AC 2 A

Pay station power supply (V) 12 DC

Current draw (A) 10

Power draw (W) 100

Display (") TFT LCD 9.7

Print head life (km) 100

Cutting blade life (no. of cuts) 1,000,000

Operating temperature (°C) 0 - 40

Storage temperature (°C) -20 to 70

Environmental humidity (%) 20 to 70

Material ABS

Weight of PC and external power supply (kg) 5

Paper roll

Dimensions

Page

3 - Manual

FA00593-EN

FA00593-EN - ver.

1 - 02/2017 - © CAME S.p.A. - The contents of this manual are subject to change at any time without prior notice.

GENERAL INSTALLATION INSTRUCTIONS

Installation must be carried out by qualified and experienced personnel in compliance with applicable

regulations.

Preliminary checks and warnings

Before putting into operation, check the following:

• ensure that the PC is switched off;

• it is forbidden to use the product for purposes other than those envisaged or in an improper manner;

• Ethernet connections must be made to the highest standards of workmanship and tested and certified 10/100

Mbit;

• for network connections, follow the IEEE ISO/OSI 802.3 or IEEE 802.11 standards to the letter;

• check with your network administrator about the static IP address to be assigned to the device;

• check that there are suitable electrical protections against short circuits and leaks to earth;

• do not use on or near a heat source or near water;

• place the pay station on a flat, stable, vibration-free surface;

• make sure the pay station ventilation openings are not obstructed.

Description of the components

1. PC with touchscreen display

2. VFD display for customer side

3. Front thermal printer cover

4. Upper rear cover for connectors / serial ports /

USBs

5. Lower rear cover for connectors / serial ports /

USBs

6. Fairlead hole

7. RFID HF proximity reader

8. Printer opening lever

9. Ticket/receipt exit slot

10. Paper holder

11. Paper feed button

12. Status indicator LEDs

13. Paper roll

14. On/off switch

15. Mouse

16. Keypad

17. Power supply

18. Power cable

OUTPUT

䞡䞣 VGA

䞢䐱䐲

䐮䐭

䐯

丈

䐱典

䞡

兹

Page

4 - Manual

FA00593-EN

FA00593-EN - ver.

1 - 02/2017 - © Came S.p.A. - The contents of this manual are subject to change at any time without prior notice.

Connections

Lower I/O: connect the pay station to the power supply, the keypad, the mouse and the Ethernet .

Upper I/O: If necessary, remove the top cover to access additional communication ports.

PUTTING INTO OPERATION

Optional devices

19. Barcode ticket reader

20. Roboticket desktop printer

21. Additional display for user side

22. Cash box

23. RFID HF or LF reading device

To put the accessories into operation, refer to their instruction sheet.

Page

5 - Manual

FA00593-EN

FA00593-EN - ver.

1 - 02/2017 - © CAME S.p.A. - The contents of this manual are subject to change at any time without prior notice.

How to access the system

Make sure all connections have been made correctly.

- Turn on the pay station .

- The operating system and the application start automatically.

- On the authentication screen, enter the default login credentials: username = admin

password = admin

Replacing the paper / Paper jam

- Open the cover using the side lever and manually intervene on the roll.

Close the cover again, leaving a flap of paper outside.

Resetting the cutter

If the cutter does not return to its original position, open the cover then turn the printer off and back on again.

This will force a reset and bring the blade back to the home position.

INDICATOR LED

Type LED Description

Blue

Orange

System on

System in standby

Red Flashing indicates printer busy

OUT Red Out or almost out of paper

Page

6 - Manual

FA00593-EN

FA00593-EN - ver.

1 - 02/2017 - © Came S.p.A. - The contents of this manual are subject to change at any time without prior notice.

TROUBLESHOOTING

Problems Possible causes Solutions

Power LED off • No power • Connect the power supply

LED on and audible signal • Out of paper • Change the paper roll

LED on • Almost out of paper • Change the paper roll

Alarm LED flashing and audible

signal

• Abnormal power supply • Switch the printer off and check

the power supply

• The print head has overheated • Turn off the printer and wait for

the head to cool down

• Cutter error • Reset the cutter

• The cover is open • Close the cover

• Sensor test errors • Contact service

Printing is not clear • The head is dirty • Check the paper quality

• Clean the print head and the roller

The paper is not moving through

correctly

• The paper is jammed • Remove the jammed paper

MAINTENANCE

It is forbidden to use solvents.

Display

- Use a damp microfibre cloth.

Printer

Turn off the printer and open the cover.

- Use a damp cotton cloth for the plastic parts.

- To clean the sensors, the print head and the roller, use a cotton cloth and isopropyl alcohol.

Close the cover after the alcohol has evaporated completely.

Page

7 - Manual

FA00593-EN

FA00593-EN - ver.

DISMANTLING AND DISPOSAL

CAME S.p.A. implements an EN ISO 14001 certified and compliant Environmental Management System at

its plants, to ensure environmental protection. Please continue our efforts to protect the environment, something

that CAME considers to be one of the foundations in developing its business and market strategies, simply by

observing brief recommendations as regards disposal:

DISPOSAL OF PACKAGING

Packaging components (cardboard, plastic etc.) can be disposed of together with normal household waste

without any difficulty, by simply separating the different types of waste and recycling them. Before proceeding, it

is always advisable to check specific regulations in force in the place of installation.

DISPOSE OF PROPERLY!

DISPOSAL OF THE PRODUCT

Our products are made with different materials. Most of them (aluminium, plastic, iron, electrical cables) can

be disposed of together with normal household waste. They can be recycled if collected, sorted and sent to

authorised centres. Other components (control boards, transmitter batteries etc.) on the other hand, may contain

pollutants. They should therefore be removed and handed over to companies authorised to recover and recycle

them. Before proceeding, it is always advisable to check specific regulations in force in the place of disposal.

DISPOSE OF PROPERLY!

REGULATORY REFERENCES

The product complies with the applicable reference directives.

MARKETED PRODUCT.

www.came.com

CAME S.p.A.

Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c

31030

Dosson di Casier

Treviso

Treviso - Italy

33079

Sesto al Reghena

Pordenone

Pordenone - Italy

(+39) 0422 4940

(+39) 0422 4941

(+39) 0434 698111

(+39) 0434 698434

The contents of this manual are subject to change at any time without prior notice.

CAME PS ONE Installation guide

CAME PS ONE Installation guide

CAME PS ONE Installation guide

Related papers

Other documents