Cooper Lighting NeoSwitch - 120/277/347V Dual Tech/Single Level Wall Switch Sensor (Ground Required) Installation guide

Installation Instructions

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Model # ONW-D-1001-347-W

Model # ONW-D-1001-347-V

Model # ONW-D-1001-347-LA

Model # ONW-D-1001-347-G

Model # ONW-D-1001-347-B

NeoSwitch Dual Technology Single Relay

Occupancy Sensing Wall Switch

(Ground Required)

• Readallinstructionsonbothsidesofthis

sheetrst

• InstallinaccordancewithALLlocalcodes

• Forindooruseonly

General Information

Technology:PassiveInfrared(PIR)andUltrasonic(US)

Electrical Ratings:

347VAC:

• Incandescent/Tungsten–

Max.load:4.3amps,1500W,50/60Hz

• Fluorescent/Ballast–

Max.load:4.3amps,1500W,50/60Hz

Ballast Compatibility:Compatiblewithmagneticand

electronicballasts

No Minimum Load Requirement

Time Delays:Self-Adjusting,15seconds/test(10min

Auto),Selectable5,15,30minutes

Coverage:Majormotion–1000sq.ft.

 Minormotion–300sq.ft.

Light Level Sensing:0to200foot-candles

Operating Environment:

• Temperature:32°F–104°F(0°C–40°C)

• RelativeHumidity:20%to90%non-condensing

Housing:Durable,injectionmoldedhousing.

PolycarbonateresincomplieswithUL94VO.

Size:

• MountingPlate/StrapDimensions:

4.35"Hx1.732"W(110.49mmx44mm)

• ProductHousingDimensions:2.618"Hx1.752"

Wx1.9"D(66.5mmx44.5mmx48.26mm)

LED Indicators:RedLEDindicatesPIRdetection;

GreenLEDindicatesUltrasonicdetection.

Speciﬁcations

Description

Coverage

TheONW-D-1001-347OccupancySensingWallSwitchisaPassiveInfrared(PIR)andUltrasonic(US)motion

sensinglightingcontrolandconventionalwallswitchall-in-one,usedforenergysavingsandconvenience.

ThesensorcombinesPIRandUStechnologiestomonitoraroomforoccupancy.

PIR Technology

Thesensor’ssegmentedlensdividesthefield-of-viewintosensorzones,anddetectsthechangesintemperature

thatarecreatedwhenaperson,orpartofapersonassmallasahand,passesintooroutofasensorzone.

US Technology

Thesensorproducesalowintensity,inaudiblesound.Itdetectsoccupancyfromchangesintheacousticwaves

causedbymotion,suchasreachingforatelephone,turningapageinabook,walkingintoaroom,turningina

swivelchair,etc.Thesensordoesnotrespondtoaudiblesound.

DualTechnologysensorsensurethegreatestsensitivityandcoveragefortoughapplicationsthussavingadditional

energy.PIRisusedtoturnthelightsONandtheneitherorbothtechnologiesareusedtokeepthelightsON.

TheONW-D-1001-347allowsthecontrolofoneloadwithoneoccupancysensorswitch.

ThesensorcanbeconfiguredtoenhanceenergysavingsbysettingtheunitforManualONoperation.

InAutomaticONMode,

thelightsturnONautomaticallywhenapersonenterstheroom.InManualONMode,the

lightsareturnedONbypressingtheuniversallyrecognizedlighticonpushbutton.Ineithermode,thelightsstayON

aslongasthesensordetectsmotionintheroom.Whentheroomisvacated,thelightsturnOFFautomaticallyaftera

presettimedelayinterval.

Thesensorincludesself-adaptivetechnologythatcontinuallyadjuststoconditionsbyadjustingsensitivityandtime

delayinreal-time.Byadjustingsensitivityandtimedelayautomatically,thesensorismaximizingthepotentialenergy

savingsthatareavailableintheparticularapplication.

TheDaylightingfeaturepreventslightsfromturningON,whentheroomisadequatelyilluminatedbynaturallight.

TheWalk-ThroughfeaturemaximizesenergysavingsbynotleavingthelightsONafteramomentaryoccupancy.

ThesensorwillswitchthelightsONwhenitdetectsapersonenteringthearea.Ifthesensordoesnotcontinueto

detectmotion20secondsfollowingtheinitialactivation,itwillautomaticallygotoashorter2minutetimedelay.

TheON/OFFButtonDisableOption–WhenselectedthisoptiondisablestheON/OFFbutton(s)andsensor

becomesautomaticonlycontrol.

TheONW-D-1001-347isdesignedforofficesupto300squarefeet.

Location

WheninstallingtheONW-D-1001-347inanewjunctionbox,choosetheswitchlocationcarefullytoprovideoptimum

coverageoftheoccupiedarea.Whenreplacinganexistingwallswitch,bearinmindthattheremustbeaclear

line-of-sightbetweenthesensorandtheareatobecovered.AvoidpointingtheONW-D-1001-347directlyintothe

hallwaywhereitmaydetectpassers-by.

Installation

TheONW-D-1001-347canbeinstalledinanystandardsinglegangbox.Itmay

beinstalledinthesamemannerasanordinarywallswitch.

• WiretheONW-D-1001-347asdescribedinthewiringsection

• MounttheONW-D-1001-347inthejunctionbox

Wiring

CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned

OFF at the branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used

as the main switch for a fluorescent lighting circuit, the circuit breaker should be marked “SWD.” All

installations should be in compliance with the National Electric Code and all state and local codes.

NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact fluorescent lamps (CFLs) is

shortened by frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the

effects of cycling.

1. MakesurepoweristurnedOFFatthebranchcircuitbreaker.

2.Wireunitsasshowninwiringdiagramsperapplicablevoltagerequirements.

3.Mountunittowallbox.

4.TurnpowerbackONatthebranchcircuitbreakerandwait2minutesfortheunittostabilize.

5.Makenecessaryadjustments.(SeeCheckoutandAdjustmentssection)

6.Installwallswitchplate.

LOAD

347 VAC

BLACK

BLUE

NEUTRAL

GROUND

GREEN

Wiring Diagram 1:

347 VAC single level

single circuit wiring diagram

LOAD 1

347 VAC

BLACK

BLUE

NEUTRAL

GROUND

GREEN

LOAD 2

A/B SWITCHING USING TOGGLE

SWITCH TO TURN OFF SECOND LOAD

Wiring Diagram 2:

347 VAC single level switch

dual level wiring using a toggle

switch wiring diagram

Minor Motion, IR

Major Motion, IR

Maximum coverage area may

vary somewhat according to room

shape and the presence of obstacles.

The NEMA WD 7 Guide and robotic

method were utilized to verify

coverage patterns.

Minor Motion, Ultrasonic

Major Motion, Ultrasonic

P/N 9850-000314-01

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Printed in Malaysia

Sensitivity Adjustments

Ultrasonic Sensitivity(GreenLED)–Usingasmallflatheadscrewdriverturnthe

greenpotentiometersothatthearrowpointsU P.

1. Standindifferentareasoftheroomandwaveyourhands.

2. IftheGreenLEDdoesnotturnON,increasetheUSsensitivitybyturningthe

greenpotentiometerclockwiseinsmallincrements.RepeatStep1.

3. Standstillthreetofourfeetawayfromsensorforfiveseconds.LEDshouldnot

turnON.

4. IfGreenLEDturnsONwithoutmotionorisconstantlyONdecreasethe

US sensitivitybyturninggreenpotentiometercounter-clockwiseinsmall

decrements.RepeatStep3.

Note:DoNotadjustsensitivityhigherthannecessary.

PIR Sensitivity

1. Standindifferentareasoftheroomandwaveyourhands.

2. IftheRedLEDdoesnotturnON,checkforanyobstructions.

3. Standstillthreetofourfeetawayfromsensorforfiveseconds.LEDshouldnot

turnON.

4. IfRedLEDturnsONwithoutmotionorisconstantlyONadjustPIRsensitivityto50%bymovingDIPSwitch5up.

Field-of-view outside the space

1. AdjustPIRsensitivityto50%bymovingDIPswitch5up.

2. Usenon-reflectivetapestripstocovertheportionsofthesensorlensthatviewoutsidethespace.

3. AdjustUltrasonicSensitivity.

ON/OFF Disabled Feature

1. ON/OFFButtonDisableOption–Whenselected

thisoptiondisablestheON/OFFbuttonandsensor

becomesautomaticonlycontrolregardlessofthe

settingforautomaticormanualactivation.Thisfeature

willnotallowsomeonetoturnlight(s)OFFviathe

pushbuttonwhilepeopleareincommonareassuchas

restroom,breakroomandcopyroomareas.

Daylight Adjustments

TheDaylightingfeaturepreventsthelightsfromturningONwhentheroomisadequatelyilluminatedbynaturallight.Ifthereis

enoughlightintheroomregardlessofoccupancy,thesensorwillholdthelightsOF F.Ifthereisnotenoughlightintheroom,the

sensorwillallowthelightstoturnONwhenoccupied.ThesensorwillnotallowtheDaylightingfeaturetoturntheloadOFFuntilthe

spaceisvacantorthelightlevelrisesabovethesetpointandthetimedelayexpires.WhileinManualActivationMode,ifsomeone

attemptstoturntheloadONandthereissufficientdaylightavailabletheDaylightingfeaturewillholdthelightsOF F.

1. Setthelightlevelwhentheambientlightisatthelevelwherenoartificiallightisneeded.Ifthisfeatureisnotneeded,leavethe

lightlevelatmaximum(fullyCW).

2. Withtheload(s)ON,putthesensorintoTestMode.ToplaceintoTestMode,toggleDIPswitch8outofitscurrentposition,wait

3secondsandthenbackintoitsoriginalposition.

3. Setthelightleveltominimum(fullyCCW).

4. Letthesensortime-outsolightsareOFF.Enterthe

spaceandlightsshouldremainOF F.

5. Makesurenottoblockthesensorfromthedaylight

sourceandadjustthelightlevelpotentiometerCWin

smallincrements.(Pause5secondsbetween

eachadjustment)

6. LightswillnotturnONuponoccupancyactivation,

whentheambientlightlevelexceedsthedaylight

thresholdsetting.

Time Delay Adjustments

Peoplewhoremainverystillforlongperiodsoftimemayneedalongertimedelaythanthedefaultsettingof10minutes.As

longastheself-adjustingfeatureisenabled,theswitchwillrespondtoeachpairoffalse-OFFswithnonormalOFFinbetween,by

alternatelymakingslightadjustmentstoeithertimedelay(by2minuteincrements)orsensitivity,sothereshouldbenoneedfor

manualadjustment.Ifmanualadjustmentisdesired,refertoTimeDelaysettingsinDIPswitchlegend.

ResetsensortimedelaytofactorysettingsbymovingDIPswitches1and2down.(IfDIPswitches1and2arealreadydown,

toggleDIPswitch1outofitscurrentposition,wait3seconds,andthenbacktoitsoriginalposition)

Override

TheOverridesettingallowsthesensortooperateasaserviceswitchintheunlikelyeventoffailure.

1. MoveDIPswitch12up.

2. ThepushbuttoncanbeusedtomanuallyturnlightsONorOFF.

Warranties and Limitation of Liability

DIP Switch Settings

Troubleshooting

Pleaserefertowww.coopercontrol.comundertheLegalsectionforourtermsandconditions.

Checkout and Adjustment

LOAD 1

BLACK

BLUE

NEUTRAL

THREE-WAY WIRING DIAGRAM:

LIGHTS WILL TURN OFF, WHEN UNIT THAT WAS TURNED ON LAST AND/OR DETECTED MOTION LAST TIMES-OUT.

GROUND

GREEN

347

VAC

BLACK

BLUE

GROUND

GREEN

TRAVELLER

WIRES

Wiring Diagram 3: 347 VAC single level single circuit three-way wiring diagram

CAUTION: If a room is wired for two circuits using two separate hot leads, it is very important to connect only one circuit

per relay. Both circuits must be fed from the same phase.

Issue Possible Causes Suggestions

Lights

Will Not

Turn ON

automatically

SensorisinManualONmode

Presspushbutton.IfAutoModeis

desiredchangeActivationModetoAuto.

SensorwasturnedOFFmanually.Ifthe

SensorwasturnedOFFmanuallybefore

thetimedelayexpired,lightswillremain

OFFfortheremainderofthetimedelay

PressthepushbuttontoturnthelightsbackON

DaylightingFeatureEnabled

IfalllightsarerequiredtoturnON

adjustdaylightpotentiometer

Powerinterruption Checkincomingvoltageand/orwiring

Lights

Will Not

Turn ON

manually

DaylightingFeatureEnabled

IfalllightsarerequiredtoturnON

adjustdaylightpotentiometer

Powerinterruption Checkincomingvoltageand/orwiring

ON/OFFButtonDisabled MoveDIPSwitch7down

If lights will still not turn ON, set sensor to override mode and call Technical Services at 1-800-553-3879

Lights

Will Not

Turn OFF

automatically

Override MakesuresensorisnotinOverrideMode

Self-Adjust

IfsensorisinSelf-AdjustMode,itmaybe

possiblefortheunittohaveincreasedthetime

delaytoa30minutedelay.Ifthelightsdonot

turnOFFafter30minutesfollownextstep.

30MinuteDelay

Maximumtimedelayis30Minutes.CheckDIP

SwitchestoverifyDIPSwitchsettings.Iflightsdo

notturnOFFatthesettimedelay,checknextstep

UltrasonicSensitivitysetHigh

Lowersensitivitybyturninggreen

potentiometerCCWinsmalldecrements

PIR

activatedbyheatsource

otherthanoccupant

MoveDIPSwitch5up

Lights

Will Not

Turn OFF

manually

CallTechnicalServices

ON/OFFButtonDisabled MoveDIPSwitch7down

If lights will still not turn OFF, call Technical Services at 1-800-553-3879

12345678

5 Minutes

15 Sec Test/Auto*

Time Delay

DIP Switch

Activation PIR Sensitivity Not UsedOverrideMaintain Lights On Not Used

Relay 1 Not Used

ON/OFF ButtonWalk-Through Mode

15 Minutes

DIP Switch Legend

121196





Disable

Enable









Auto

Manual





Full

50%









Enable

Disable

Enable





Either

Both

Default =

30 Minutes

*Self-Adjusts to

10 min. user

mode



9101112

AdjustmentsshouldbemadewiththeHVACsystemONsothattheinstallerwillbeabletodetecttheeffectofairflowonthe

operationoftheONW-D-1001-347.Useonlyinsulatedtoolstomakeadjustments.

Immediatelyafterapplyingpowertothelightingcircuit,waitapproximatelytwominutesfortheswitchtopower-upandstabilize.

Self-Adjust

Sensorisshippedinself-adjustmode.Thisappliestotime

delay,USandPIRsensitivity.InpreparationfortheInstaller

Test,thetimedelayissetto15seconds,afterthesensoris

installed,poweredONandhasstabilized,theunitwilltime-

out15secondsafterthelastmotiondetected.Coverageand

sensitivitycanbeconfirmedbywatchingtheGreen(US)and

Red(PIR)indicatorLEDsonthefrontofthesensor,while

movingaroundtheroom.

1. WalkaroundtheroomandmonitorLEDs.

2. Standindifferentpartsoftheroomandwaveyour

hands.LEDsshouldonlyturnONforonesecondwith

eachmotion.(IfLEDsdonotturnON,gotoInstaller

Adjustments–SensitivityAdjustmentSection)

3. Standstillthreetofourfeetawayfromsensorfor

fiveseconds.LEDsshouldnotturnON.(IfanyLED

turnsON,noteLEDandgotoInstallerAdjustments–

SensitivityAdjustmentssection)

4. Walkoutsidetheroomandwait15secondsforthelightstoturnOFF.(IflightsdonotturnOFFgotoInstaller

AdjustmentsSection)

5. Re-entertheroomtoactivatesensor.(IflightsdonotturnONgotoTroubleshootingSection)

6. Atthispointyoucanexittheroomandletthesensortime-out.Whenthesensortimes-outandisOFFwithpowerONforfive

minutes,theunitwillgotoa10minuteTimeDelayusermodesetting.

Note:ToplaceintoTestMode,toggleDIPSwitch12outofitscurrentposition,wait3seconds,andthenbackintoitsoriginalposition.

ON/OFF Button

PIR Lens

DIP Switches

Ultrasonic Detection

Daylight

Sensor Level

Adjustment

Ultrasonic

Sensitivity

Adjustment

Red (PIR) & Green (US)

Detection LEDs

1 and 2

345678

9101112

12345678

9101112

Installer Adjustments

Cooper Lighting NeoSwitch - 120/277/347V Dual Tech/Single Level Wall Switch Sensor (Ground Required), ONW-D-1001-347-V, ONW-D-1001-347-W Installation guide

Related papers

Other documents