Andersen Hinge Replacement Service Instructions

Brand: Andersen

Model: Hinge Replacement

Type: Service Instructions

9069228 BA Revised 06/20/13

Tools Needed Herramientas necesarias

∙Safety Glasses Lentes de seguridad

∙Flat Blade Screwdriver Flat Blade Screwdriver

∙Drill/Driver Drill/Driver

∙#2 Phillips Bit #2 Phillips Bit

Hinge Replacement

for E-Series Push Out Casement Windows

for E-Series/Eagle® Push Out Casement Windows

Parts Included Partes incluidas

(1) Hinge Hinge

Hinge

Thank you for choosing Andersen.

For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com.

Please leave this guide with building owner.

Si tiene alguna pregunta llame al 1-888-888-7020. Para obtener más información y/o guías, visite www.eaglewindow.com

Deje esta guía con el dueño de la construcción.

▶Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.

Lea completamente la guía antes de comenzar la instalación. Lea y respete todas las advertencias y precauciones durante la instalación de la unidad.

▶Check with your local building code ofcial to identify and conrm compliance with local building code requirements.

Consulte los códigos locales de construcción para identicar y conrmar que se cumplan los requisitos del código de construcción.

Use caution when working at elevated

heights and around unit openings. Follow

manufacturers’ instructions for ladders and/

or scaffolding. Failure to do so may result in

injury or death.

Follow manufacturers’ instructions for hand

or power tools. Always wear safety glasses.

Failure to do so may result in injury and/or

product damage.

Windows and doors can be heavy. Use safe

lifting techniques and a reasonable number of

people with enough strength to lift, carry and

install window and door products to avoid injury

and/or product damage.

9069228

Remove screws from bottom restrictor arm track and save screws for

reuse. Repeat for top restrictor arm.

▶For windows with restrictor arm (width more than 30"),

proceed to Step 2.

▶For windows without restrictor arm (width less than 30"),

proceed to Step 4.

Restrictor

Arm Track

Restrictor Arm

Sill

Unlock and open sash.

Interior

Windows with Restrictor Arm Only

Drill/Driver

Restrictor Arm

Restrictor Arm 2

Exterior

Rotate top and bottom restrictor arm and restrictor arm track toward sash.

Restrictor Arm

Restrictor Arm Track

Windows with Restrictor Arm Only

Exterior

Rotate top and bottom hinge arm toward sash.

Rotate upper and lower hinge arm toward sash.

Exterior

Release bottom hinge arm from hinge channel stud using a at blade screwdriver. Repeat for top

hinge arm.

Releasing hinge arm allows sash to

swing freely. Sash may suddenly

swing out and break free causing

injury and/or product damage.

Support sash during entire

replacement process.

Hinge Channel Stud

Flat Blade Screwdriver

Hinge Arm

Sill

Exterior

9069228

Hold sash rmly and slide top and bottom hinge shoes from ends of hinge channels. Place sash on a clean, at surface with interior side facing up.

Hold sash rmly and slide upper and lower hinge shoes from ends of hinge channels. Place sash on a at surface with interior side facing up.

Hinge Shoe

Hinge Channel

Windows and doors can be heavy. Use safe lifting techniques and a reasonable

number of people with enough strength to lift, carry and install window and door

products to avoid injury and/or product damage.

Exterior

Remove hinge screws from top and bottom of sash. Save for reuse.

Remove hinge screws using a drill/driver and save for reuse.

Position new hinges tight to sash.

Position new hinge tight to sash.

Remove hinges and dispose of properly.

Remove hinge and dispose of properly.

Fasten hinges using saved screws.

Fasten hinge using saved screws.

7 8

910

Lift sash into unit opening. Position top hinge shoe into end of top hinge channel rst, then bottom hinge shoe into end of bottom hinge

channel and slide sash in place.Lift sash into unit opening. Position upper hinge shoe into end of upper hinge channel rst, then lower

hinge shoe into end of lower hinge channel and slide sash in place.

9069228

Hinge Shoe

Hinge Channel

Exterior

Close and lock sash.

▶Hinge replacement is complete.

Hinge replacement is completed.

Re-engage top and bottom hinge arm to hinge channel stud.

Re-engage upper and lower hinge arm to hinge channel stud.

Reposition top and bottom restrictor arm track and fasten using saved

screws.

Windows with Restrictor Arm Only

Restrictor

Arm Track

Restrictor Arm

Sill

Drill/Driver

Exterior

Interior

Hinge Channel Stud

Sill

Hinge Arm

Exterior

Andersen Hinge Replacement Service Instructions

Andersen Hinge Replacement Service Instructions

Andersen Hinge Replacement Service Instructions

Related papers

Other documents