Anova D1300 Assembly & Instruction Manual

Brand: Anova

Model: D1300

Type: Assembly & Instruction Manual

Anova D1300 is a 6’ Picnic Table, a perfect addition to any backyard or park. The table is made of sturdy materials and is easy to assemble. It comes with all the necessary hardware and instructions. The table is also easy to clean and maintain. With its classic design, the Anova D1300 6’ Picnic Table is sure to provide years of enjoyment for you and your family.

anovafurnishings.com

888.535.5005 tel

1 — In Ground

Support

2 — Seats

ASSEMBLY INSTRUCTIONS

D1300 6’ Picnic Table

F1300 6’ Picnic Table

TOOLS NEEDED:

Ratchet with 1/2” Socket•

Ratchet with 3/4” Socket•

1/2” Open-end or Box-end Wrench•

3/4” Open-end or Box-end Wrench•

Level•

24 — 5/16”

Washer

12 — 5/16” x 1.25”

Hex Head Bolt

ASSEMBLY:

The assembly is a two-person operation.

1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.

2. Locate the two Seats and lay them out on the packing

cardboard or other so surfaced workspace upside

down. Find the Seat Supports and position one of them

over each Seat as shown.

3. Align the mounting holes in the Seat Support

with the holes in the Seat frame. Install one of the

5/16” Washers onto one of the 5/16” x 1.25” long Bolts

and insert the Bolt through both parts. Install a 5/16”

Washer and 5/16” Flanged Nut on the end of the Bolt.

Leave the hardware nger tight.

Repeat this for the remaining mounting holes of both

Seats and Seat Supports.

ASSEMBLY HARDWARE:

BENCH COMPONENTS:

8 — 1/2 x 7.5”

Hex Head Bolt

1 — Tabletop

2 — Seat Supports2 — Tabletop

Supports

12 — 5/16”

Flanged Hex Nut

5/16” Washer

5/16” Flanged Nut

Seat Frame

5/16” Washer

Seat Support

5/16” Bolt

Seat

Seat Support

Packaging cardboard

or other so work

surface

8 — 1/2”

Flanged Hex Nut

16 — 1/2”

Washer

7.5” long Bolt

1/2” Washer

1/2” Flanged Nut

Cardboard or other

so work surface

5/16” Bolt

5/16” Washer

5/16” Flanged Nut

4. Locate the Inground Support and set it on the work surface

with the end with the mounting holes down. Position the Seat

Support assemblies on either side of the Inground Support. The

Seat Support assemblies attach to the sides of the Inground

Support with only 4 holes.

Install one of the 1/2” Washers onto one of the 1/2” x 7.5” long

Bolts. Align the mounting holes in the Seat Supports with the

mounting holes in the Inground Support and install the Bolt

through the set of mounting holes all three parts.

Repeat this for each of the remaining 7.5” long Bolts. Aer all

four Bolts are installed, Use the 3/4”-Rachet and 3/4”- Open or

Box End Wrench to tighten the hardware.

1/2” Washer

7.5” Long Bolt

1/2” Nut

Seat Support

Inground Support

Do not drag the assembled unit across any surface.•

This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to •

remove surface dirt. Do not clean with a solvent or petroleum based products.

Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, •

missing, or broken hardware, and general instability.

Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced. •

Repairs must be made using only factory authorized parts and methods.•

WARNING

CARE AND

MAINTENANCE

211 North Lindbergh Blvd.

St. Louis, MO 63141

tel: 888.535.5005

web: anovafurnishings.com

10/2012

Ground Level

24.00”

30.00” MIN

Temporary Structure to hold

the assembly vertical, level,

and at the correct height

Drain Hole

1/2” Washer

1/2” Flanged Nut

7.5” Long Bolt

1/2” Washer

5/16” Washer

5/16” Flanged Nut

1.25” Long Bolt

5/16” Washer

6. The walls of the concrete base should be vertical and smooth

to minimize the eects of frost upheaval. This can be achieved

with the use of concrete forms, such as Sonotube. Consider

extending the concrete base below the frost line. Consult a

professional for loose or unusual soil conditions.

7. Create a Temporary Structure that will be used to support the

Inground Support Assembly, at the desired height and level,

while the concrete is curing.

8. Fill the form with concrete and insert the Inground Support

Assembly, centered in the concrete, until the Seat Supports

are supported by the Temporary Structure. Allow the interior

of the Inground Support to ll with concrete up to the Drain

Hole. Crown the concrete cap to optimize drainage. Allow the

concrete to cure before attaching the Table Top Supports.

Aer the concrete has cured, the installation hole is backlled,

and the Temporary Structure is removed, use the

Ratchet with

1/2” Socket and the 1/2” Open or Box End Wrench to tighten

the Seat hardware.

Check with a Level and adjust the Seats as

needed while tightening.

10. L

ocate the Table Top Supports and position them on opposite sides of

the Inground Support, in the proper orientation. Align the mounting

holes in the Table Top Supports with those in the Inground Support.

Place one of the 1/2” Washers on one of the 7.5” long Bolts and insert

the Bolt through both Table Top Supports and the Inground Support

mounting holes. Apply a 1/2” Washer and 1/2” Flanged Nut to the

end of the Bolt and tighten nger tight. Repeat for the other three

mounting holes. Aer all Bolts are installed, use the Ratchet with 3/4”

Socket and the 3/4” Open or Box End Wrench to tighten the Nuts.

11. Locate the Table Top and carefully place it on top of the

Table Top Supports. Place one of the 5/16” Washers on

one of the 1.25” long Bolts and insert the Bolt through

the mounting holes in the Table Top Support and Table

Top frame. Add one of the 5/16” Washers and 5/16”

Flanged Nuts to the end of the Bolt and tighten nger

tight.

Repeat for the other mounting hole in that end of the

Table Top. Fasten the other end of the Table Top to the

other Table Top Support in the same manner.

Aer all bolts are installed,

use the Ratchet with 1/2”

Socket and the 1/2” Open or Box End Wrench to tighten

the Nuts.

Check with a Level and adjust the Table Top as

needed while tightening.

12. Retighten all hardware two weeks aer initial assembly.

5. Determine the location for the Table.

IMPORTANT: Locate underground utilities and avoid them while digging the hole for the concrete base.

Anova D1300 Assembly & Instruction Manual

Anova D1300 Assembly & Instruction Manual

Anova D1300 Assembly & Instruction Manual

Related papers

Other documents