anovafurnishings.com
888.535.5005 tel
1 X Bench Seat 2 X Bench Support
ASSEMBLY INSTRUCTIONS
F1360 6 Ultra Flat Bench
F1389 4 Ultra Flat Bench
D1360 6 Ultra Flat Bench
D6011 6 Rally Flat Bench
TOOLS NEEDED:
Ratchet with 3/4” Socket•
ASSEMBLY:
The assembly is a two-person operation.
1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.
2. Locate one of the Bench Supports and the Bench Seat and lay them out on the packing cardboard or other so
surfaced workspace.
3. Turn the Bench Seat upside down. Align
the mounting holes in the mounting bosses
of the Bench Support with the holes in
one end of the Bench Seat. Install one of
the Spring Washers, then one of the Flat
Washers onto one of the 1/2” x 1.5” Hex
Head Bolts. Make sure the concave face
of the Spring Washer is toward the Flat
Washer. Insert the Bolt through the Bench
Seat and thread it into the Bench Support.
Leave the Bolt nger tight.
Repeat this for the other mounting hole on
the same end of the Bench Seat.
Aer both Bolts are installed, use the
Ratchet with 3/4” Socket to tighten the
Bolts
.
Model F1360 shown.
Seat pattern may vary.
ASSEMBLY HARDWARE:
BENCH COMPONENTS:
Spring Washer
(concave face
toward Flat Washer)
1/2” Hex Head Bolt
Flat Washer
Bench Seat Bench Support
Mounting Boss
Bench Seat
Bench Support
Packaging cardboard or
other so work surface
4 X Spring
Washer
4 X 1/2”
Flat Washer
4 X 1/2 -13 x 1.5”
Hex Head Bolt
Spring Washer
1/2” Hex Head Bolt
Flat Washer
Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to •
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, •
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced. •
Repairs must be made using only factory authorized parts and methods.•
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: 888.535.5005
web: anovafurnishings.com
Spring Washer
1/2” Hex Head Bolt
Flat Washer
.5” DIA Surface Mounting Hole
4. Repeat for the two mounting holes on the other side
of the Bench Seat.
5. Turn the bench upright and move it to the desired location.
NOTE: The Bench Feet have .5” diameter surface mounting
holes in case you want to prevent the bench from being
moved. Surface mounting hardware is not included.
10/2012
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Anova RCPWF6 Assembly Instructions
-
-
-
-
-
-
-
-
-
Other documents
-
PROSPOTfitness Fusion SSG Owner's manual
-
Precor Discovery Olympic Bench Series Assembly Manual
-
ProSpot Fitness HG-5 User manual
-
Bowflex ULTIMATE 2 Assembly Manual
-
-
-
LifeGear 76310 Owner's manual
-
HoistFitness CF-CU Owner's manual
-
Weider BODY BLASTER FORCE 4 90102 User manual
-
Stamina Titan 650 System Owner's manual
