Anova F1032 Assembly Instructions

Anova
Brand
Anova
Model
F1032
Type
Assembly Instructions

This manual is also suitable for

anovafurnishings.com
888.535.5005 tel
2 x End
Armrest
1 x Contour Bench Seat
12.00”
26.50”
Ground Level
24.44”
TOOLS NEEDED:
1/2” Open-end or Box-end Wrench• 
Ratchet with 1/2” Socket• 
Level• 
16 x
5/16”
Washer
8 x
5/16”
Flanged Hex Nut
8 x
5/16” X 1.5”
Hex Head Bolt
ASSEMBLY:
The assembly is a two-person operation.
1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.
2. Place the Contour Bench Seat on the shipping
packaging or other so surface to avoid scratching
the product.
NOTE: When viewing the Bench Seat from the end,
the edge with three holes is the seat portion and the
edge with one hole is the backrest portion.
3. Locate one of the End Armrests and position it at
one end of the Bench Seat. Line up the holes in the
Armrest with the mounting holes in the end of the
Bench Seat. Place a Washer on a Bolt and insert the
Bolt through the Armrest and through the mounting
hole in the Bench Seat. Place a Washer and Flanged
Nut on the end of the Bolt and tighten nger
tight. Repeat this process for the other end of the
Armrest. Aer both sets of hardware are installed,
tighten with the Wrench and Ratchet.
Attach the other End Armrest at the other end of
the Bench Seat in the same manner.
Model F1036 shown.
ASSEMBLY HARDWARE:
BENCH COMPONENTS:
1 x Center Armrest
with
Additional Hardware
2 x In Ground
Bench Support
Washer
Flanged Nut
Washer
Bolt
Armrest
Packaging cardboard or
other so work surface
Additional Feature
Model F1036VB Only
3a. For model F1036VB only: Locate the Center Armrest and
additional Hardware Package. Position the Center Armrest near
the center of the Bench Seat, with both ends of the Armrest
snug against the Bench Seat. Place a small Washer (5/16”)
on each Bolt. Insert one Bolt through one end of the Center
Armrest and through an opening in the Bench Seat. Insert the
other Bolt through the other end of the Center Armrest and
through an opening in the Bench Seat.
Check that the Center Armrest is vertical and in the desired
position. Reposition the Center Armrest if necessary.
When the Center Armrest is correctly positioned, put one of the
large washers (7/16”) on one of the Bolts, then a small Washer
(5/16”), then add the Flanged Nut. Tighten nger tight.
Add a large Washer, then small Washer, and Flanged Nut to the
other Bolt, then tighten both Nuts.
12.00”
26.50”
Ground Level
24.44”
Washer
Bolt
Small Washer
Flanged Nut
Washer
Bolt
Flanged Nut
Large Washer
Small Washer
Large Washer
ASSEMBLY INSTRUCTIONS
F1032 4  Courtyard Bench
F1036 6  Courtyard Bench
F1036VB 6  Courtyard Bench with Center Armrest
Do not drag the assembled unit across any surface.• 
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to • 
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, • 
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced. • 
Repairs must be made using only factory authorized parts and methods.• 
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: 888.535.5005
web: anovafurnishings.com
10/2012
4. Locate one of the Bench Supports and position it at one end of the Bench Seat. Align the mounting holes in one of the Bench
Supports with the holes in the appropriate end of the Bench Seat. Install a Washer onto one of the provided Bolts and insert the
Bolt through both parts, with the Bolt head on the outside surface of the Bench Support. Install a Washer and Nut on the inside
end of the Bolt.
Leave the hardware nger tight so that adjustments can be made during assembly.
12.00”
26.50”
Ground Level
24.44”
12.00”
26.50”
Ground Level
24.44”
In Ground
Bench Support
Washer
Flanged Nut
Washer
Bolt
Install a Bolt and Washer through
the other set of mounting holes
in that end of the Bench Support
and Bench Seat and install a
Washer and Nut. Again, leave the
hardware nger tight.
5. Attach the other Bench Support
to the Bench Seat in the same
manner. Leave the hardware
nger tight.
6. Tighten the Bench hardware
using the Open End or Box End
Wrench and Ratchet Wrench;
minor adjustments can be made
while tightening the hardware to
make the Bench Seat and Seat
Supports square.
7. Determine the location for bench, locate underground
utilities and avoid them while digging holes for
concrete bases.
8. The walls of the concrete base should be vertical and
smooth to minimize the eects of frost upheaval.
This can be achieved with the use of concrete forms,
such as Sonotube. Consider extending the concrete
base below the frost line to eliminate the possibility
of frost upheaval. Consult a professional for loose or
unusual soil conditions.
9. Create a temporary structure that will be used to
support the bench, at the desired height and level,
while the concrete is curing.
10. Fill the forms with concrete and insert the supports,
centered in concrete, until bench is supported by
the temporary structure. Allow supports to ll
with concrete. Crown the concrete cap to optimize
drainage.
11. Aer the concrete has cured, remove the temporary
structure and retighten all hardware.
  • Page 1 1
  • Page 2 2

Anova F1032 Assembly Instructions

Anova
Brand
Anova
Model
F1032
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents