anovafurnishings.com
888.535.5005 tel
ASSEMBLY INSTRUCTIONS
F1031 4 Courtyard Gull Wing Bench
F1035 6 Courtyard Gull Wing Bench
TOOLS NEEDED:
1/2” Open-end or Box-end Wrench•
Ratchet with 1/2” Socket•
Level•
24 x
5/16”
Washer
12 x
5/16”
Flanged Hex Nut
12 x
5/16” X 1.5”
Hex Head Bolt
ASSEMBLY:
The assembly is a two-person operation.
1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.
2. Place the Bench Seat upside down on the shipping
packaging or other so surface to avoid scratching the
product. Locate one of the Bench Supports and position
it near the end of the Seat.
3. Align the mounting holes in the Bench Support with the
holes in the bracket on one end of the Bench Seat. Install
a Washer onto one of the provided Bolts and insert
the Bolt through both parts, with the Bolt head on the
outside surface of the Bench Seat. Install a Washer and
Flanged Nut on the inside end of the Bolt.
NOTE: Installing the Bolt in this direction reduces the risk of
scratching during use.
Leave the hardware nger tight so that adjustments can
be made during assembly and leveling.
Install a Bolt and Washer through the other set of
mounting holes in that end of the Bench Seat and
Support and install a Washer and Flanged Nut. Again,
leave the hardware nger tight.
ASSEMBLY HARDWARE:
BENCH COMPONENTS:
4. Attach the other Bench Support to the Bench Seat in
the same manner, installing the Bolts from the outside
inward. Leave the hardware nger tight.
1 x
Bench Seat
2 x
Bench Support
2 x
Cross Brace
2 x
Arm Rest
Support
Seat
Bracket
Washer
Flanged
Nut
Washer
Bolt
Washer
and Bolt
Washer and
Flanged Nut
packaging cardboard or
other so surface
Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to •
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, •
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced. •
Repairs must be made using only factory authorized parts and methods.•
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: 888.535.5005
web: anovafurnishings.com
10/2012
5. Locate one of the Cross Braces and position it so that the
mounting hole in one end aligns with the mounting hole in the
bracket in the center of the Seat Support. Place it on the back
side of the bracket. Put a Washer on one of the Bolts and insert
the Bolt through the Cross Brace and Seat Support bracket and
put a Washer and Flanged Nut on the end of the Bolt.
Leave the hardware nger tight so that adjustments can be
made while assembling and leveling.
Install a Bolt and Washer through the mounting holes in the
other end of the Cross Brace and Seat Center Bracket and install
a Washer and Flanged Nut. Again, leave the hardware nger
tight.
Holes for
surface mounting
Washer and Bolt
Washer and
Flanged Nut
Washer and Bolt
Washer and
Flanged Nut
Washer and
Flanged Nut
Washer
and
Bolt
Seat Center
Bracket
6. Attach the other Cross Brace to the Seat and other Seat Support
in the same manner. Leave the hardware nger tight.
7. Turn the bench upright. Locate one of the Arm Rests and position
it at one end of the Bench Seat. Line up the holes in the Arm Rest
with the mounting holes in the Bench Seat end. Place a Washer
on a Bolt and insert the Bolt through the Arm Rest and through
the mounting hole in the Bench Seat. Place a Washer and Flanged
Nut on the end of the Bolt and tighten nger tight. Repeat this
process for the other end of the Arm Rest. Aer both sets of
hardware are installed, Tighten with the Wrench and Ratchet.
Attach the other Arm Rest at the other end of the Bench Seat in
the same manner.
8. Tighten all hardware while checking with a Level.
9. Move the assembled Bench to the desired location.
NOTE: The feet of the Bench include surface mounting holes in
case a permanent installation is desired. Follow installation
instructions provided with the hardware if purchased.
10. Retighten hardware two weeks aer initial assembly.
/
