Anova L1361 Assembly Instruction

Brand: Anova

Model: L1361

Type: Assembly Instruction

This manual is also suitable for

anovafurnishings.com

888.535.5005 tel

ASSEMBLY INSTRUCTIONS

L1360 6  Rendezvous Bench

L1360A 6  Rendezvous Bench

L1361 4  Rendezvous Bench

L1504 4  Horizon Bench

L1506 6  Horizon Bench

L1506A 6  Horizon Bench

Bench End

Screw

Washer

Nut

Contour

Bench Seat

Bench End

Screw Washer

Nut

Contour

Bench Seat

Packaging plastic and

cardboard to avoid

scratching the product

.50”

.66”

TOOLS NEEDED:

9/16” Open-end or Box-end Wrench•

Ratchet with 9/16” Socket•

#4 Phillips Screwdriver•

Level•

ASSEMBLY HARDWARE:

NOTE: Hardware arrives in two packages; one with each Bench End.

4 x

3/8”

Washer

4 x

3/8”

Nylock Hex Nut

4 x

3/8” X 1.5”

Phillips Head Screw

ASSEMBLY:

The assembly is a two-person operation.

1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.

2. Place the Contour Bench Seat on the shipping

packaging or other so surface to avoid

scratching the product.

Note: Before assemblying the Nuts to the

Screws, it is recommended that a light oil

or petroleum jelly be applied to the screw

threads

3. Align the mounting holes in one of the

Bench Ends with the holes in the appropriate

end of the Bench Seat. Insert one of the

provided Screws through both parts, with

the screw head on the outside surface of the

Bench End. Install a Washer and Nut on the

inside end of the Screw.

Note: Always hold the screw head still and turn

the Nut. This protects the surface of the

Bench around the Screw from scratches (the

Washer protects the nut side of the Bench)

Leave the hardware nger tight so that

adjustments can be made to level the bench

seat.

Model L1360 shown.

Seat pattern may vary.

1 x Contour Bench Seat

2 x Bench Ends

1 x Center Armrest

Model L1360a only

Do not drag the assembled unit across any surface.•

This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to •

remove surface dirt. Do not clean with a solvent or petroleum based products.

Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, •

missing, or broken hardware, and general instability.

Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced. •

Repairs must be made using only factory authorized parts and methods.•

WARNING

CARE AND

MAINTENANCE

211 North Lindbergh Blvd.

St. Louis, MO 63141

tel: 888.535.5005

web: anovafurnishings.com

09/2013

Bench End

Screw

Washer

Nut

Contour

Bench Seat

Bench End

Screw Washer

Nut

Contour

Bench Seat

Packaging plastic and

cardboard to avoid

scratching the product

.50”

.66”

Bench End

Screw

Washer

Nut

Contour

Bench Seat

Bench End

Screw Washer

Nut

Contour

Bench Seat

Packaging plastic and

cardboard to avoid

scratching the product

.50”

.66”

The feet of the Bench Ends

feature a surface mount cutout

for securing the Bench with

customer supplied surface

mount hardware.

Bench End

Screw

Washer

Nut

Contour

Bench Seat

Bench End

Screw Washer

Nut

Contour

Bench Seat

Packaging plastic and

cardboard to avoid

scratching the product

.50”

.66”

Surface mount cutout dimensions

Install a Screw, Washer, and Nut through the other set

of mounting holes in that end of the Bench Seat. Again,

leave the hardware nger tight.

4. Attach the other Bench End to the Bench Seat as shown.

Leave the hardware nger tight so adjustments can be

made to level the Bench Seat.

5. Tighten the Bench Seat hardware using the Screwdriver

and Ratchet Wrench while checking the seat surface

with a Level; minor adjustments can be made while

tightening the hardware to make the seat level.

6. Retighten all hardware two weeks aer initial assembly.

Bench End

Screw

Washer

Nut

Contour

Bench Seat

Bench End

Screw Washer

Nut

Contour

Bench Seat

Packaging plastic and

cardboard to avoid

scratching the product

.50”

.66”

The Models L1360A L1506A benches

have three additional holes in the center

seat slat to mount a Center Armrest.

Position the Armrest with the threaded

studs inserted through the mounting

holes. Fasten the Armrest using a

Flat Washer and Nylock Nut on each

mounting stud.

Anova L1361 Assembly Instruction

Brand: Anova

Model: L1361

Type: Assembly Instruction

This manual is also suitable for

Download PDF

report

Anova L1361 Assembly Instruction

This manual is also suitable for

Anova L1361 Assembly Instruction

Related papers

Other documents