Page is loading ...
C50.B7000.00E-1
3-speed fan
controller
5.25" to 3.5"
convertor
140mm blue
fan
ODD
module
Two 140mm
blue LED fans
with filter
120mm fan
120mm fan
HDD module
Patented
Tool-less PCI
add-on card
holder
Patented
tool-less 5.25”
device mounting
Side panels installation
Loose the screw and pull the
latch to release the side panel.
Press the right and left side
of the bezel to remove
Pull the front panel
toward yourself.
Just press plastic handle to
release the mounting bracket.
Push the CD-ROM into the ODD
module, Close the bracket.
3-speed fan
adjustable device
ODD installation
Loose the screw
Remove the side panel.
Cable
Management
bezel
6
6
4
2
10
8
4
2
8
10
6
2
4
10
8
USB
5
5
3
1
9
7
1394
3
1
7
9
5
1
3
9
7
USB
4
2
10
6
8
3
1
9
5
7
HD AUDIO
AC'97
10
9
8
6
7
5
2
4
1
3
MIC
EAR
Blue(PORT2 L)
Black(SENSE SEND)
Yellow(PORT2 R)
Brown(PORT1 R)
Red(PORT1 L)
Green(SENSE2 RETUR)
KEY
Orange(SENSE1 RETUR)
Black(PRESENCE)
Black(GND)
Black(AGND)
NC
Yellow(R-RET)
KEY
Blue(L-RET)
Red(MIC)
Brown(MIC-PWE)
Yellow(R-OUT)
Blue(L-OUT)
KEY
Black(GND)
Green
White
Red
Black(GND)
Green
White
Red
KEY
Black(GND)
Green
White
Red
Black(GND)
Green
White
Red
Black(KEY)
White(+12V)
Green(TPB+)
Black(VG)
Blue(TPA+)
SATA Cable
USB
USB
IEEE1394
E-SATA
Connector
Black(GND)
White(+12V)
Red(TPB-)
Black(VG)
Orange(TPA-)
Vents for
water cooling
Place the water tube
through the rubber cover.
Removable fan filter
Hardware list
PCI card holder-S(4)
PCI card holder-L(3)
Thumb screw(7)
for PCI card holder
Thumb screw(12)
& rubber ring(12)
Thumb screw(3)
for HDD cage
Mounting bracket
for SSI CEB/EEB M/B
(8)
(2)
(14)
1
for cable management
(28)
Box(1)
for spare parts
Thumb screw(9)
for mount
Thumb screw(3)
for mount
Tool-less PCI add-on card installation
5.25" bezel
Vented PCI
slot
Stand off
Hex wrench for M/B(1)
stand-off
for work with stand-off
Please visit www.lian-li.com for FRANCE / GERMANY / SPAIN user's manual
Veuillez visiter www.lian-li.com pour le manuel d’installation en FRANÇAIS/ALLEMAND/ESPAGNOL.
Visite el sitio Web www.lian-li.com para obtener el manual del usuario en FRANCÉS ALEMÁN Y ESPAÑOL
Besuchen Sie bitte www.lian-li.com für die französische/ deutsche/ spanische Gebrauchsanleitung
Installation Guide
PSU tray(1)
HDD holder bracket(1)
C50.B7000.00E-2
PSU installation
VGA Card Pillar Installation Guide
1
2
3
4
1. Fasten the HDD screws with
anti-vibration rubber rings to the HDD.
2. Slide the HDD into the HDD
cage with the anti-vibration kit.
3. Press down the HDD into the
slots to secure.
Adding extra screw to
the HDD cage for extra
security.
Note:
Hard disk installation for modularized HDD cage
Loosing four screws remove the
HDD module
Change fan direction
Also can fit on 5.25" rack tray
Multi-Position HDD Module
Remove HDD module
To the bottom of the case
In the 5.25" rack
Remove four screws at the base of the
case to release the PSU stand PSU
stand before install the HDD module.
F
POWER SW
RESET SW
POWER
LED
H.D.D LED
SPEAKER
WHITE
GRAY
WHITE
BLUE
WHITE
NC
GREEN
WHITE
ORANGE
BLACK
NC
NC
RED
GROUND
PWR
GROUND
Reset
PLED-
PLED+
IDE_LED-
IDE_LED+
Speaker
+5V
Front panel cable installation
guide
Loosing two thumb screws to release the M/B tray.
Secure the stand-off bolts on the M/B tray which
match with the M/B fix points,place the M/B on the
copper bolt, fasten with the thumb screws to secure.
1
2
3
for SSI CEB/EEB
The oval hole on M/B tray
designed for special server
boards, please use nut to
hold the copper bolt in place.
Note: For area where hard to
reach use the long
thumb screw
!
!
!
1. First, remove HDD holder from
HDD cage.
2. Open the HDD holder's clip.
3. Insert HDD into HDD holder,
close the clip to secure.
4. Slide the HDD holder into the
HDD cage.
Use the HDD
holder bracket
to secure the
holder in place.
Hard disk installation
Note
Adding extra screw
to the HDD cage for
extra security.
Secure the 2.5” HDD fo the
base of the case sit below
3.5" HDD
Note:
mounting bracket mounting bracket
to
Note:
Adding cushion to hold
slim vision 3.5" HDD in
HDD holder.
/
