Page is loading ...
1
IMPORTANT:
Go to www.extron.com for the
touchpanel user guide and installation
instructions before connecting the
touchpanel to a power source.
www.extron.com
AMK 1, AMK 2, and AMK 3 • Installation Guide
Overview
ATTENTION:
• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and
national building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes du
bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
These angle mount kits are used to mount touchpanels to walls or glass surfaces. The angle mount allows the touchpanel to be
mounted at a lower accessible height while still being viewable from higher or lower lines of sight.
• The AMK 1 is used to mount the TLS 525M, TLP Pro 525M, and TLC Pro 526M.
• The AMK 2 is used to mount the TLS 725M, TLP Pro 725M, and TLC Pro 726M.
• The AMK 3 is used to mount the TLS 1025M, TLP Pro 1025M, and TLC Pro 1026M.
gure 1
Before Starting
To run cables to the back of the touchpanel, remove the cable access cover (see
gure 1,
E
) by releasing the catches (
D
) and pulling the cover away.
There is a slot on either side of the cover (see gure 2,
G
) that can
accommodate the at Ethernet cable. If you are using a larger cable, cut away
the plastic tabs (
H
) from the sides of the cover using a sharp knife along the
groove in the plastic (see gure 1,
F
).
To replace the cover, slide the tabs (
C
) into the notches on the back of the
enclosure and press the catches (
D
) back into place.
Option 1: Mounting the AMK to a Wall with Fasteners
To mount the AMK to a wall or furniture, drill holes through the four dimples in
the plastic (
B
) and attach the AMK. The installer must use screws and fasteners
that are appropriate for the mounting surface.
Option 2: Mounting the AMK to a Glass Surface
1. Clean both sides of the glass with a lint-free cloth and a 1:1 mixture of
isopropyl alcohol and water.
2. Place the alignment template on the inside glass surface (see gure 3,
1
).
Use tape (
2
) to attach the alignment guide to the glass. Use a level (
3
) to
ensure it is at the correct angle.
3. Remove the plastic backing from the adhesive patch on the back of the
AMK.
TIP: Wet your ngers to prevent them from sticking to the adhesive
patch.
C
D
A
B
E
F
Figure 1. AMK Enclosure (front view)
G
H
Figure 2. AMK Enclosure (side view)
1
Alignment Template for the Extron
AMK 2 and AMK 3
(for mounting TLS Pro 725M, TLP Pro 725M, TLS Pro 1025M, and TLP Pro 1025M)
Page size: 11" x 17"
Print scale 1:1
Do not shrink.
1.
See the Extron AMK 1, A
MK 2, and
AMK 3 Installation G
uide for
c
o
mplete instruction
s
.
2.
Doub
le-check the
p
rint settings
before printi
n
g. Make sure the scale
s
etting
s are 1:1.
3.
After
printing, c
h
e
ck that the bottom
e
d
ge of the AMK
adhesive
pa
tch
(shown in red) is 4.63
" (118
m
m).
P/N 68
-34
23-02 Rev. A
CATx cable entry
2.67"
(68 mm)
Outer edge of
TLS Pro 725M
Bottom edge
of AMK adhesiv
e
Adhesive surface
of AMK
for the Extron
d TLP Pro 1025M)
e
P/N 68
-
-34
23-
Outer edge of
TLS Pro 725M
T
e
3-02
Rev. A
R
23-
Inside Glass
Surface
Outside Glass Surface
3
2
Figure 3. Placing the Template
This guide provides instructions for professional installers to mount and install
these touchpanels using the appropriate AMK mounting kit. The diagrams in
this guide show the AMK 2 and TLP Pro 725M. Use the other kits to mount the
corresponding touchpanels in the same way.
The kits consist of:
• (1) plastic enclosure (AMK 1, AMK 2, or AMK 3; see gure 1) with an adhesive
patch attached to the back. The enclosure ships with a metal plate attached to
the mounting posts (see gure 1,
A
).
• (1) cover overlay can be attached to the opposite face of the glass to conceal
the adhesive patch (see figure 5, on the next page).
• LED overlay (AMK 2 and AMK 3 only, see figure 6,
1
, on the next page).
• (4) M3 screws (
6
).
• (1) 10 foot (3 meter) at Ethernet cable with RJ-45 connectors.
You must also download the alignment template from www.extron.com. One
template is for the AMK 1. A second template is for both the AMK 2 and AMK 3.
Print it at 100% size. Do not scale.
2
© 2019 Extron Electronics — All rights reserved (www.extron.com). All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
AMK 1, AMK 2, and AMK 3 • Installation Guide (Continued)
4. Do one of the following (see gure 4, inset):
• Hold the AMK at an angle with the bottom away from the glass
and align the top edge of the AMK with the red dotted line on
the alignment template marked “Top edge of AMK...”. Rotate
the bottom of the AMK so that the adhesive pad attaches to the
glass.
• Hold the AMK at an angle with the top away from the glass and
align the bottom edge of the AMK with the red solid line on the
alignment guide marked “Bottom edge of AMK...”. Rotate the
top of the AMK so that the adhesive pad attaches to the glass.
5. Press the AMK rmly against the glass (see gure 4,
1
).
6. Remove the paper alignment template from behind the glass.
Mounting the Cover Overlay (Optional)
The cover overlay is not required for mounting the touchpanel, but can
improve the aesthetics of the AMK when it is viewed through the window
from inside the conference room.
TOP
Mounting Plate
1
2
4
3
4
4
LED Overlay
TLS 725M
Back View
1
TLS
72
5M
TL
5
6
Figure 6. Mounting the TLS 725M to the AMK 2
Alignment Template for the Extron
AMK 2 and AMK 3
(for mounting TLS Pro 725M, TLP Pro 725M, TLS Pro 1025M, and TLP Pro 1025M)
Page size: 11" x 17"
Print scale 1:1
Do not shrink.
1.
See the Extron
AMK 1,
AMK 2,
and
AMK 3 Ins
tallation Guide
for
comp
lete instructions.
2.
Double-check the print settings
before printing. Make sure the scale
settin
gs ar
e
1:1.
3.
After printing, check that the bottom
edg
e of the AMK
adhesive patch
(show
n in red) is 4.63" (11
8 mm).
P/N 68-3423-02 Rev. A
Oute
r edge of
TLS Pro 725M
Bottom edge
of AMK adhesiv
e
Adhesive surface
of AMK
Out
e
r edge of
TLS Pro 1025M
Align
me
nt Templat
e for th
the
Extron
AMK 2 and
AMK
K 3
(for mounting TLS Pro 725M, TLP Pro 725M
, TLS Pr
ro
1025M, and
LP Pro 1
TL
025M
M)
Page size: 11
"
x 17
"
Print scale 1:1
Do not shrink.
1.
Se
See th
the Extr
tr
on
n
AMK 1,
A
AMK
MK 2,
and
nd
MK 3
3 Ins
tal
all
AM
A
ation Guide
de
ati
for
r
e
om
mp
let
ete instr
tr
co
uct
ctions.
2.
Do
oub
ble-c
-check
the
e print set
t
t
ting
gs
t
befo
ore
re pr
rintin
g. Ma
Make sure t
th
g.
e s
scale
settin
tin
g
n
gs a
ar
e
1
:1.
3.
After p
r pr
printi
ti
ng, che
eck
ck that
the
e botto
ttom
edg
e o
of
f the
e AM
adhe
hesive pat
tc
K
a
h
(show
n
n i
in re
ed)
is 4.
4.63
3
"
(11
8 mm
m).
23-02
Adhesive surfac
e
of AMK
02
02
Rev. A
-02
P/N 68
-3423-01 Rev. B
1
Bottom edge
of AMK adhesiv
e
of AMK adhesiv
e
1
1
1
P/
/N 68-34
342
Oute
r edge of
TLS Pro 725M
O
ut
e
r edge of
TLS Pro 1025M
P/N
68
-3423-01 Rev.
B
AMK panel
aligns to
red lines.
Top of AMK
r
ear panel
Figure 4. Attaching the AMK to the Glass
gure 6
TIP: Wet your ngers to prevent them from sticking to the adhesive
patch.
1. Remove the paper backing from the cover overlay.
2. Position the cover overlay behind the AMK enclosure and secure it to
the glass (see gure 5).
3. Use a credit card or similar at edge to remove any air bubbles.
Mounting the Touchpanel
Figure 6 shows how to mount the TLS 725M to the AMK 2. Mount the
other touchpanels to the corresponding mounting kit in exactly the same
way.
1. If required, remove the paper backing, and attach the LED overlay
to the back of the touchpanel (see gure 6,
1
). This overlay covers
the rear panel LEDs so that they do not cause a distraction inside the
conference room.
2. Run cables through the gap left by removing the cable access cover
(see Before Starting on the previous page) to the AMK and through
the mounting plate.
Connect the cables to the touchpanel (see the user guide for
your touchpanel model).
3. Fasten the mounting plate (provided with the touchpanel)
to the metal plate that comes with the AMK, using the four
provided M3 screws (
2
).
4. Attach the Ethernet cable to the LAN/PoE input on the
rear panel of the touchpanel (see the user guide for your
touchpanel model).
5. The mounting plate for the 5" models has two hooks (one
in each top corner). The mounting plates for the 7" and 10"
models have four hooks (
3
), (one in each corner)
Position the touchpanel so that these hooks t into the slots
on the rear panel of the touchpanel (see the user guide for
your touchpanel model).
6. Slide the touchpanel down slightly so that the hooks are
seated securely in the slots.
7. The tongue at the bottom of the mounting plate (
4
) sits in
the groove in the bottom of the touchpanel (see inset,
5
).
Fasten the touchpanel to the mounting plate by tightening
the lock screw (
6
).
Cover
Overlay
Figure 5. Attaching the Cover Overlay
gure 5
68-3317-01 Rev. B
09 19
/
