FURNITURE FSDH-TOPKT-4-DD Installation guide

Brand: FURNITURE

Model: FSDH-TOPKT-4-DD

Type: Installation guide

FURNITURE FSDH-TOPKT-4-DD is a versatile rail system designed for hanging doors. It features adjustable mounting brackets for easy installation on various surfaces. The rail can be trimmed to fit your specific needs, and the included end caps provide a clean and finished look. With a weight capacity of up to 100 lbs per door, this system is suitable for a wide range of applications, including closets, pantries, and room dividers.

Architectural Products by Outwater assumes no liability for improper installation.

MODEL No. FSDH-TOPKT-*-4-DD INSTALLATION MANUAL

TOOLS REQUIRED INCLUDED IN KIT

• Plumb Line

• Pencil

• Phillips Head Screwdriver

• 4mm Drill Bit

• Wrench

• Level

• Power Drill

• Tape Measure

FURNITURE

ADoor Roller Hardware x4

BAnti-Jump Disk x4

CDoor Stop Hardware x2

DEnd Cap x2

EMounting Bracket for ¾" and 1" Doors x3 ea.

FM6x60 Bolt + Washer x6

GRouted Door Guide x2

HST4.2x35 Screw x4

IAnchor x4

J1.5mm Allen Key x1

KHole Cover x4

L48" Rail x1

A B C D

E F

G H

PLEASE NOTE: The installation manual is a suggested guideline. Adjustments may need to be made based on your specic application.

Architectural Products by Outwater assumes no liability for improper installation.

3 ½” 3 ½”

48”

8” 16”16” 8”

Using a pencil, mark the locations where you will drill holes

as indicated.

Using a power drill with a 4mm drill bit, drill holes as indicated.

Before beginning installation, attach the door stops [C]

to the rail [L].

UNDERSTANDING YOUR RAIL

INSTALLATION

Architectural Products by Outwater assumes no liability for improper installation.

Install the rail, and mounting brackets [E].

Mounting Bracket [E]

Drill holes into the doors as indicated. Attach the door rollers [A].

It is suggested that the door rollers [A] be mounted 5" from the edge of the doors

to the neck of the rollers.

NOTE: Trimming the rail will alter the position of the roller hardware.

Adjust accordingly.

Architectural Products by Outwater assumes no liability for improper installation.

3⅛"

FOR ¾" DOORS

FOR 1" DOORS

Allow a minimum 3-1/8" clearance above the doors.

Architectural Products by Outwater assumes no liability for improper installation.

Door Roller [A]

Anti-Jump Disk [B]

(x2)

Attach the anti-jump disks [B] to the doors.

Attach the doors to the rail [L] and lock the anti-jump disks [B] into position. Doors should be routed beforehand

if using the routed door guides [G].

Anti-Jump Disk [B]

(x2)

Architectural Products by Outwater assumes no liability for improper installation.

Use the hole covers [K] to give the rail a

nished look.

Once cut, add the end caps [D] to the ends of the rail and secure with a

set screw.

NOTE: If you are trimming the rail, do so equally. Each

rail can be trimmed equally up to 2½" on both sides.

However; trimming will alter the position of the roller

hardware. Adjust accordingly.

Routed Door Guide [G]

Hole Covers [K]

The rail can be trimmed if necessary using a band saw

or hacksaw. Use blades suitable for iron or stainless

steel depending on your rail.

End Cap [D]

2½" Max

If using the routed door guides [G], install them at this time.

Repeat steps 4-7 for additional door.

FURNITURE FSDH-TOPKT-4-DD Installation guide

FURNITURE FSDH-TOPKT-4-DD Installation guide

FURNITURE FSDH-TOPKT-4-DD Installation guide

Related papers

Other documents